How to remove the front bumper of Baojun 730?

[VonJayden]

The method to remove the front bumper of Baojun 730 is: first remove the screws at the bottom of the front bumper, then open the front hood. There are three more screws under the headlights that secure the bumper to the car's frame. Remove these screws on the frame to complete the process. The front bumper of a car is typically a hydraulic cold-stamping product, mostly made from seamless steel tubes through processes like tube bending, pre-forming with a press, final forming with a press, and then hole punching and marking with a laser cutting machine. The Baojun 730 is a model under SAIC-GM-Wuling Baojun, with body dimensions of 4780mm in length, 1820mm in width, and 1755mm in height, and a wheelbase of 2750mm. In terms of exterior design, the rear styling of the Baojun 730 has undergone significant adjustments, with reduced chrome trim and an enlarged tailgate that spans the entire width of the rear end.

[DeMicah]

I've done the DIY project of removing the front bumper of the Baojun 730 several times myself, and it's quite fun. First, prepare a Phillips screwdriver and a plastic pry bar—avoid using metal tools to prevent scratching the car body. Open the hood and locate the screws at the bottom of the front bumper, usually near the wheel arch liners. There are about seven or eight in total; unscrew them gently. Next, deal with the clips—these plastic fasteners break easily, so pry them off slowly and carefully. Be cautious when unplugging the fog lights or radar connectors to avoid damaging the wires. Once everything is removed, the front bumper can be taken off—just be careful not to bump the lights or other parts. After removal, it's a good idea to clean out any accumulated dust or rust inside and apply some lubricant to prevent aging. The whole process takes about half an hour. Last time, I did this when modifying the grille. Beginners should remember to wear gloves for protection and avoid dropping the clips, as they can shatter.

[CassidyLynn]

I don't think removing the front bumper should be done casually. The mounting points on the Baojun 730's front bumper are quite delicate, typically with several screws located under the hood and inside the front wheel wells. First, disconnect the negative battery terminal to prevent short circuits, then carefully remove the screws and clips with tools. If the clips are aged, they can easily break, making replacement quite troublesome. After removal, check for any loose wiring or hidden rust spots. I tried it myself once and accidentally loosened a sensor wire, which caused the driving warning light to stay on afterward. It's best to have the 4S shop handle it during routine maintenance—safety first, don't take risks.

[LeClayton]

Directly explain the disassembly steps: First, remove the screws inside the wheel arches, typically three on each side for the Baojun 730; disconnect the fog light or sensor connectors; then use a pry bar to start prying open the plastic clips from under the hood, gently shaking the front bumper to remove it; the entire process takes about 10 minutes. Be sure to use the appropriate tools to avoid damaging the car paint. After removal, clean the interior dust to prolong its lifespan.

[McSavannah]

Speaking from years of experience in DIY car repairs, removing the front bumper of a Baojun 730 requires a step-by-step approach. Prepare your tools and keep them handy—a screwdriver and soft plastic pry bars work best. Start from the wheel arches by unscrewing all bolts, and remember their positions to avoid misplacement. Pry open the clips at multiple points to prevent breakage from excessive force. After removal, inspect the internal cushioning pads for aging or damage, and replace them promptly to prevent abnormal noises. I've seen cases where people skipped this step, leading to increased body vibration. Stay calm throughout the process, and take your time—it's manageable with patience.

[JuneRose]

Speaking of this, my friend asked me about removing the front bumper of the Baojun 730 last time. Simply put, first locate all the fixing screws, such as those under the front of the car and above the wheels. Gently unscrew them, don’t force them. Take your time with the clips; I saw him pry them off with a plastic tool in a few tries. Remember to disconnect the fog light wiring harness before removal to avoid any flashing. After removal, clean the dust inside the front bumper, and it looks much newer. The whole process isn’t difficult, just be patient.