How to Remove and Install the Rear Seats of the Qashqai?

[DeAutumn]

Method for removing and installing the rear seats of the Qashqai: Before removal, pull the edge of the rear seat cushion and lift it forcefully to create a gap in the car seat. Use a flashlight to locate a clip, then insert the removal tool into the middle of the clip and push it in about 4cm. Press down firmly, and the seat cushion will be lifted. Repeat the same process for the clip on the other side, and the car seat will then be removed. To install the seat, align the clips on the seat. First, insert the inner tongue of the seat cushion, then align it with the pulled-out clip and press down firmly. A clicking sound indicates that the seat is properly installed. The Qashqai has body dimensions of 4315mm in length, 1783mm in width, and 1606mm in height, with a wheelbase of 2630mm. It features front-wheel drive and has a fuel tank capacity of 65 liters.

[LeElla]

I've taken apart the Nissan Qashqai's rear seats several times, and experience tells me to start with the seat cushion. Wear a pair of gloves and avoid using brute force to prevent scratching the interior. There are usually plastic clips under the front edge of the backrest—slide your fingers in from the edge and gently lift upward until you feel it release. Some model years might have a hidden handle near the center console; pulling it lifts the cushion. For split seats, there are clips on both sides. After removing the cushion, you'll find metal hooks and release straps at the base of the seatback—pull the strap or hook to unlock, then tilt the seatback forward to remove it. Be careful not to touch wiring connectors, especially in higher trims with seatbelt sensors. Once removed, cleaning dust under the seats is easy, but keep small parts away from children. When reinstalling, align the clips properly and press down firmly until you hear a click to ensure locking. The whole process shouldn’t take more than 10 minutes—just a basic flathead screwdriver as a pry tool is enough.

[OKinsley]

As a car owner, I was a bit nervous the first time I removed the rear seats of my Qashqai, but it turned out to be quite simple. First, clear any debris from the seats, then check if the front edge of the seat cushion is secured to the car floor—most Qashqai seat cushions are held by clips. Feel for the raised parts at the rear sides of the cushion with your hands and pull upward firmly to release them. To remove the backrest, pull the fabric strap at the bottom or side of the seat, which releases the hooks, then push the entire seat forward to remove it. When reinstalling, make sure the hooks are securely fastened to avoid rattling while driving. Avoid using excessive force during the process; if the clips are too tight, apply some lubricant. For safety, it's recommended to perform this in an open area to avoid accidentally triggering the airbags. Removing the seats makes it easier to clean hard-to-reach areas or add floor mats, which is very practical.

[McLondyn]

Safety first! Before removing the rear seats of the Nissan Qashqai, disconnect the negative terminal of the car battery as a precaution. The seat cushions often have hard plastic clips secured underneath – wear gloves and pry them open slowly to avoid hand injuries or scratching the interior floor mats. For the backrest, locate the release strap or lever at the bottom to disengage the locking hooks. Once unlocked, carefully tilt and remove it, checking for any wiring connections to disconnect first. When reinstalling, ensure all anchor points are securely fastened and gently shake to test stability. Keep the entire process under 15 minutes to prevent seat structure damage, and avoid performing this task in humid conditions.

[BradyMarie]

DIY Nissan Qashqai rear seat removal is super easy – just prepare a flathead screwdriver and a cloth. Start with the seat cushion: use your hand or a tool to hook and instantly pop the clip at the front center, then lift and remove the cushion. The backrest has pull straps on the sides; tug them to unlock and fold the entire seat forward for removal. After clearing the interior space, you can add soundproofing mats or replace seat covers. Pro tip: Lubricate the clips before reinstallation to reduce wear, and keep the screw holes under the seat dust-free. It’s a fully manual job requiring no special skills, but patience is key to avoid bending the clips.

[GiselleLynn]

After family trips, the rear seats often get dirty from the kids, making the disassembly and assembly of the Qashqai seats a routine for me. The seat cushions are secured with clips—just locate the raised points at the bottom on both sides and lift gently to remove, avoiding hard pulls to prevent breakage. The backrest is released by pulling the seat bag cord, then pushing it down for removal and cleaning. When reinstalling, align the locking positions carefully and press firmly until you hear a click to ensure safety. Multiple experiences have taught me that post-disassembly cleaning is super convenient, extends seat lifespan, and allows for chassis inspection.