···
Log in / Register

How to Operate the Rear Wiper of Baojun 510

6Answers
VonMiranda
07/29/2025, 12:01:24 AM

The operation method of the rear wiper of Baojun 510 is as follows: 1. Locate the wiper control lever on the right rear side of the driver's seat; 2. The three gears on the left side of the control lever are used to adjust the speed of the front wiper; 3. The second gear on the right side of the control lever is used to turn on the rear wiper; 4. The off gear on the right side of the control lever is used to turn off the rear wiper. Taking the Baojun 510 2021 model as an example, its body structure is a 5-door, 5-seat SUV, with body dimensions of: length 4220mm, width 1740mm, height 1615mm, wheelbase of 2550mm, fuel tank capacity of 45l, and trunk capacity of 318 to 1210l.

Was this review help?
115
Share
LillianaRose
08/12/2025, 11:39:25 AM

Operating the rear wiper of the Baojun 510 is quite straightforward. On the wiper control stalk located on the right side of the steering wheel, there's usually a rotary knob or a small lever specifically for the rear wiper function. Turning it in one direction activates the wiper modes—for example, the first turn sets it to intermittent wiping, and the second turn to continuous slow-speed wiping. If you want to spray water to clean the rear window, simply push the stalk upward or downward, and the spray will start. When driving, especially in rainy weather or when the rear window is dirty, always check the rear wiper position first. After using it, remember to turn it back to the off position to avoid draining the battery. I also like to regularly clean the wiper blades with a damp cloth to maintain their effectiveness and ensure clear visibility. Safe driving depends on these small details, and the operation is easy to get used to—new drivers will adapt after a few tries.

Was this review help?
1
Share
Expand All
DelBenjamin
10/02/2025, 04:18:10 AM

I've been driving the Baojun 510 for quite some time, and the rear wiper is operated via the control stalk on the right side of the steering wheel. Specifically, there's a rotary knob at the end of the stalk—twisting it activates the rear wiper. A light turn engages the intermittent mode, while turning it further switches to continuous wiping. The washer function is also convenient: simply push the stalk in a specific direction, such as downward, to spray water and clean the glass. When using it for the first time, take it slow—if you twist to the wrong setting, just adjust back. During daily driving, I turn it on during heavy rain or fog to keep the rearview clear. It's advisable to regularly check the wiper rubber for wear. If wiping becomes ineffective, use the washer to clean the glass and extend the parts' lifespan. Mastering these simple steps ensures a more confident drive.

Was this review help?
14
Share
Expand All
KylieMarie
11/15/2025, 10:13:48 PM

The rear wiper of the Baojun 510 is controlled by the knob on the right-hand stalk of the steering wheel. Turning the knob activates and adjusts the wiper. At the first position, the wiper operates intermittently; turning it further makes it wipe continuously. To spray washer fluid, simply push the stalk. I often use it when reversing or after the rain stops, as the rear window tends to accumulate dust and become unclear. A quick spray and a few wipes will clean it up. The operation is not complicated—just turn the knob as needed and return it to the original position to turn it off. Check it when the weather changes significantly to ensure driving safety.

Was this review help?
2
Share
Expand All
SanMarley
01/05/2026, 11:50:26 PM

Operating the rear wiper of the Baojun 510 is quite straightforward. Simply twist the knob at the end of the control lever on the right side of the steering wheel to activate the wiper, switching from intermittent to continuous modes. Pushing the lever sprays water to clean the glass. I recommend testing it before driving to avoid mistakes during rainy conditions. Regularly clean the wiper blades to prevent noise. This small feature is very practical in daily use, but avoid keeping it on unnecessarily to save battery power.

Was this review help?
4
Share
Expand All
KateRose
04/02/2026, 11:21:05 PM

As a Baojun 510 owner, I find the rear wiper operation quite cool. On the right-hand stalk of the steering wheel, twist the knob to activate the wiper. A light twist sets it to intermittent mode, while turning it further increases the wiping speed. To spray washer fluid, push the stalk forward. When the rear window gets blurry in rain, turning it on immediately clears the view. Remember to turn it off after use—developing this habit helps avoid issues. During regular maintenance, pay attention to component wear and replace them promptly to ensure performance.

Was this review help?
12
Share
Expand All
More Q&A

What are the principles of yielding to pedestrians?

The main principles of yielding to pedestrians are as follows: 1. If the road has no centerline division or only one motor vehicle lane in the same direction, vehicles from both directions should stop and yield. 2. If there are two motor vehicle lanes in the same direction, vehicles in both lanes should stop and yield. 3. If there are three or more motor vehicle lanes in the same direction, vehicles in the lane corresponding to the pedestrian and the adjacent front lane should stop and yield. 4. If there are no traffic lights or crosswalks on the road, drivers should actively yield when encountering pedestrians crossing the road.
120
Share

Where is the Lane Departure Warning System Switch Located?

The lane departure warning system switch does not have a fixed position. The following explains how the lane departure warning system works: 1. The system obtains the vehicle's position parameters within the current lane through image processing. When it detects that the vehicle is deviating from the lane, the sensor promptly collects vehicle data and the driver's operational status; 2. The controller then issues an alarm signal, with the entire process completed in approximately 0.5 seconds, providing the driver with more reaction time; 3. If the driver activates the turn signal and performs a normal lane change, the lane departure warning system will not issue any alerts.
111
Share

What Causes Engine Shaking During Acceleration?

There are several main reasons for engine shaking during acceleration: 1. If you notice slight shaking or deviation of the vehicle body while driving, it is usually caused by tire issues, possibly due to poor tire balance. The owner should visit a repair shop for a four-wheel alignment and dynamic balance. 2. It may be caused by deformation or imbalance of the drive shaft. This situation is more common in vehicles that have experienced chassis collisions. 3. Increased carbon deposits in the throttle body, intake tract, valves, and other components. When the engine is cold, these deposits absorb some gasoline. After the engine warms up, the gasoline evaporates, causing an overly rich air-fuel mixture during idle, which leads to unstable idle speed when the engine is warm.
119
Share

What is the purpose of an automotive ignition system?

The automotive ignition system is designed to provide spark plugs with sufficiently high-energy high voltage electricity in the correct firing order for each cylinder in spark-ignition engines, enabling the spark plugs to generate strong enough sparks to ignite the combustible air-fuel mixture. Below is some information about the ignition system: 1. The automotive ignition system includes components such as the ignition switch, ignition coil, distributor assembly, and spark plugs. 2. The ignition system serves as the fundamental power source for engine operation, constituting a crucial part among all automotive systems. It is also the system that converts gasoline into power. The performance and efficiency of the automotive ignition system significantly impact engine power, fuel consumption levels, and exhaust emissions.
116
Share

What is the general lifespan of a seat belt?

Automotive seat belts typically have a service life of 3-5 years. Below is relevant information about seat belts: Function of seat belts: A seat belt is a vehicle safety device designed to protect vehicle occupants from harmful movements that may occur during collisions or sudden stops. Replacement of seat belts: Locate the seat wiring in the vehicle, find the safety buckle wire sensor wire, and remove it. Take off the seat cushion, remove the airbag, locate the bolt securing the seat belt, detach the seat belt buckle, find the seat cushion sensor within the cushion, remove it, and proceed with installation.
117
Share

How to Reset the Low-Pressure Run-Flat Indicator?

Low-pressure run-flat indicator reset method is as follows: 1. When the car tire pressure is insufficient, the dashboard will prompt to restart the low-pressure run-flat indicator. 2. After correcting the tire pressure, press the OK button on the left side of the multifunction steering wheel until the maintenance option appears on the dashboard. 3. Click the right button on the multifunction steering wheel, then the dashboard will prompt the low-pressure run-flat indicator, press the OK button to reset. 4. After clicking the OK button, the system will ask whether the tire pressure is normal, select the yes option, and this will reset the low-pressure run-flat indicator prompt.
104
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.