How to open the fuel tank cap on the Tiggo 8?

What to Do If the Steering Wheel Drive Shaft Rusts?

Solutions for a rusted steering wheel drive shaft: You can use fine sandpaper to remove and clean the rust from the steering shaft, then melt white candle wax at a high temperature and apply the melted wax to the metal part of the steering shaft. The thickness of the wax application is up to you. The wax coating can serve as a moisture barrier and isolate the metal from air, preventing rust for several years. The drive shaft is a high-speed, minimally supported rotating body, making dynamic balance extremely important. Generally, drive shafts undergo dynamic balance testing before leaving the factory and are adjusted on a balancing machine. For front-engine, rear-wheel-drive vehicles, the drive shaft transmits the rotation from the transmission to the axle of the main reducer. It can consist of several sections connected by universal joints.

120

Share

How Long Does It Take to Get License Plates After Vehicle Inspection?

License plates can be obtained 3 days after the vehicle inspection. The documents required for motor vehicle registration include: the Motor Vehicle Registration Application Form (to be obtained and filled out), a copy of the compulsory traffic insurance policy, the vehicle purchase invoice (registration copy), the criminal investigation receipt, the original ID card and its copy, the original certificate of conformity, and for non-local residents, the floating population information registration form and the purchase tax appendix. It takes about three days from picking up the new car to getting the license plates. There are several ways to select a license plate number for a new car: 1. Automatic Selection: The car owner uses the "Acceptance Voucher" at the automatic selection machine to choose one license plate number from ten randomly selected options. 2. Self-Selection: The car owner uses the "Acceptance Voucher" at the self-selection machine to create and select a license plate number according to encoding rules. 3. Online: Log in to the traffic management bureau's website, select the online self-service license plate selection system, enter the owner's name, ID number or organization code certificate number, vehicle identification number (VIN), and invoice number. After verification, the owner can query and select a license plate number according to the encoding rules.

114

Share

Is a wheel alignment necessary after replacing brake discs?

Replacing brake pads does not require a wheel alignment, but replacing tires does necessitate both wheel alignment and dynamic balancing. Wheel alignment is based on the four-wheel parameters of the vehicle, adjusted to ensure optimal driving performance and a certain level of reliability. The installation of a car's steering wheels, steering knuckles, and front axle has specific relative positions; this installation with defined relative positions is called steering wheel alignment, also known as front wheel alignment. Brake pads, also referred to as brake linings, are critical safety components in a car's braking system. The effectiveness of all braking relies decisively on the brake pads.

114

Share

Why Can't I Make an Appointment Even After Completing the Required Training Hours?

Failing to make an appointment despite completing the required training hours may be due to reasons such as photos not meeting the requirements or the desired appointment date being fully booked. Below are the specific reasons why you might not be able to make an appointment: Photos may not meet requirements primarily because the angle of the photo does not comply with the system's standards, preventing normal approval. Some photos may have issues with the shooting angle, while others may show a significant discrepancy between the makeup appearance and the actual person. Additionally, if the photo differs greatly from the one submitted during registration, it may also affect the exam appointment. Completed training hours must be uploaded to take effect. If they are not uploaded, you cannot proceed with the exam appointment. Only when the system receives the training hour data and confirms it meets the exam requirements can you schedule the exam. Sometimes, the time you logged may not match the system's recorded duration. In such cases, you can contact the driving school to check if the training hours are insufficient or if synchronization is incomplete. As long as the traffic management department's system shows that the training hours are sufficient, you can proceed with the appointment normally. After completing the training hours, the school must report them, and the transportation management department must review them. Only after approval can you schedule the exam.

108

Share

Can the Position Lights and Low Beam Be Turned On Simultaneously?

Position lights and low beam can be turned on simultaneously. When the low beam is activated, the position lights are also turned on by default. In other words, when the low beam is turned on, the position lights will inevitably be activated at the same time. If you want the position lights to be turned on alone, there is no need to activate the low beam. Car headlights, also known as car front lights or car LED daytime running lights, serve as the eyes of the car. They not only relate to the external image of a car owner but are also closely linked to safe driving at night or under bad weather conditions. Car lights can be divided into LED lights, halogen lights, HID xenon lights, xenon lights, turn signals, position lights, fog lights, and signal lights.

106

Share

How to Disassemble the Volkswagen Headlight Switch?

Volkswagen headlight switch disassembly method: Turn the switch to the 0 position, press and hold the switch while rotating it to the right. After turning it to a certain extent, the switch can be pulled off. The headlight switch controls the front and rear lights, mirror lights, and low beams. There is also a headlight height adjustment knob near the light switch. Volkswagen is an automobile manufacturing company headquartered in Wolfsburg, Germany. The VW in its logo is the first letter of its full name, resembling three Vs made with the middle and index fingers, symbolizing the victory of Volkswagen and its products. Its models include Jetta, Passat, Lavida, Golf, Bora, etc. Taking the Lavida as an example, the car has a length of 4605mm, a width of 1765mm, a height of 1460mm, and a wheelbase of 2610mm.

116

Share