How to adjust the time on the Great Wall Wingle 5 pickup truck?

[LeMiranda]

The method to adjust the time on the Great Wall Wingle 5 pickup truck is: 1. Press the down button on the steering wheel to select the clock option; 2. Click the middle OK button to enter the clock setting page; 3. Use the down button and OK button to select the hour setting in the clock page; 4. Adjust to the desired hour and press OK; 5. Adjust the minutes by pressing the down button once for each number change, and press the OK button when the correct number is reached. The dimensions of the Great Wall Wingle 5 pickup truck are: length 5395mm, width 1800mm, height 1740mm, with a wheelbase of 3350mm. It is equipped with a 2.0T turbocharged engine, with a maximum power of 102 kW and a maximum torque of 325 Nm, paired with a 6-speed manual transmission.

[JudahAnn]

I know this well! The time adjustment for the Fengjun 5 differs between the old and new models. The old model has two buttons on the dashboard, with the MODE button being the function key. With the engine off, press and hold the MODE button for 3 seconds until the hour digits flash, then release. Short presses switch between hours and minutes, and the arrowed button adjusts the values. Press MODE again to confirm after adjustment. The new model with an LCD screen uses the menu button on the steering wheel to enter settings, select clock settings, and adjust with the volume buttons. Note that the settings reset after power loss. If it's frequently inaccurate, check the battery cables or fuses. It's best to refer to the manual, as button positions may vary by model year.

[LaMary]

Adjusting the time depends on the model year. I drive an 18 model, and there's a menu button on the left side of the steering wheel. Press it to find the clock option for adjustment. My friend's older model adjusts it on the instrument panel by pressing and holding the small cylinder in the upper left corner until the hour flashes, then using the two buttons on the right side of the instrument panel to increase or decrease the numbers. Key points: 1. Must adjust with the engine off. 2. For newer models, use the steering wheel buttons and avoid touching the center console. 3. For older models, don't press the MODE button for too long; holding it for more than 5 seconds will enter the maintenance reset mode. If the time is still inaccurate after a couple of days, it might be due to instrument panel circuit issues or unstable battery voltage.

[OVivienne]

Simple three steps: Turn off the engine, locate the MODE button (labeled SEL on some models) on the left side of the dashboard. Hold it until the hour digits blink, then press briefly to switch adjustment items, and use the ± buttons to adjust. Note! Don't press too quickly when adjusting minutes—the system has a half-second delay. Newer models with large screens can adjust more conveniently in System Settings > Vehicle > Clock. If the time keeps resetting after power loss, it's likely the coin battery behind the dashboard is dead—just replace it with a CR2032 battery.

[McMaverick]

Personal experience reveals the trick: For models 13-16, after turning off the engine, use a ballpoint pen tip to press the small hole on the left side of the dashboard (MODE button) for 5 seconds until the hour flashes. Then use the up and down buttons on the right to adjust the numbers, and press the left side again to switch to minutes. After adjustment, wait 10 seconds for automatic saving. For models after 2017 with steering wheel controls, it's more convenient—press the house icon to enter the menu, rotate the knob to select clock settings. Key reminder: Adjusting time with power on may blow a fuse! Some owners have done this, causing the dashboard backlight to fail. If the clock still runs slow after adjustment, visit a 4S shop to check the instrument module.

[DiTheo]

There are hidden tricks for adjusting the time on the Great Wall Wingle 5. For older models, press and hold the CLK button for 3 seconds when the CD player is turned on, and the clock setting will pop up on the central screen (effective for some models). Here's a cool tip for adjusting the instrument panel: when the hour is flashing, hold down the adjustment button (+) without releasing, and the numbers will jump continuously, which is three times faster than pressing it one by one. For newer touchscreen models, pay attention: first, click the gear icon in the upper right corner of the home page to enter settings, don't look for it in the radio interface. Owners who have replaced the large screen should note that for aftermarket screens, the time needs to be adjusted in the general settings, and if it's not synchronized with the original instrument panel time, a protocol box needs to be installed.