How to adjust the headlights of Wuling Hongguang S?

[LeAubree]

Steps to adjust the headlights of Wuling Hongguang S: 1. Turn on the high beams, stand in front of the headlights with your feet as close to the headlights as possible, observe where the high beams hit your feet, take the light center as the focal point, and remember this position. 2. Use a screwdriver to rotate the calibration teeth of the headlight. 3. Adjusting up and down will show obvious movement of the light center, while adjusting left and right will show less obvious movement. So don't worry if the light center doesn't move left or right, just continue turning the screwdriver forcefully until the light center aligns with the marked position. 4. Notes: It's best to do the adjustment at night, but avoid doing it on the road as it's not only dangerous but also hard to see the effect. Try to do it in a residential area or yard. Prepare a flashlight as it's hard to see clearly at night.

[VonZane]

When I first drove the Wuling Hongguang S, I also tinkered with the headlight adjustment. Open the hood, locate those two silver adjustment screws at the back of the headlight assembly—the one with a cross slot adjusts height, while the toothed one beside it controls left-right alignment. Pick a level ground, aim at a wall about 7-8 meters away at night with low beams on. Slowly turn with a Phillips screwdriver until the beam hits around waist height on the wall. Ensure symmetrical adjustments—slightly lower the left side to avoid dazzling oncoming traffic. Once, I misaligned them and couldn’t see highway signs clearly, so I pulled over immediately to readjust. Properly set headlights make night drives steadier, reduce eye strain, and most importantly, enhance safety.

[LincolnAnn]

Adjusting the headlights on the Wuling Hongguang S is quite simple—I did it myself in just two minutes. Park the car on level ground, at least five meters away from a wall, and turn on the low beams to observe the beam height. Prepare a Phillips screwdriver, and don’t confuse the two adjustment screws at the rear of the headlight housing—the vertical one adjusts height, while the horizontal one controls left-right width. Slowly turn the screws, and the changes in the light pattern on the wall will be the most obvious indicator. A key point: the left headlight should be slightly lower than the right one—this design prevents glare for oncoming drivers. After adjusting, always step out to check the actual effect, as the driver’s perspective can sometimes differ significantly from the real beam position. I keep a screwdriver in my car and regularly check the headlight alignment to prevent misalignment.

[TaliaMarie]

Wuling Hongguang S owners, take note: improperly adjusted headlights do more than just impair visibility. Last time, a friend drove with beams pointing skyward, turning high beams into low beams, nearly hitting a guardrail. Remember these three steps for correct adjustment: pop the hood and locate the adjustment holes at the back of the headlights, identifying the cross-screw positions; position the vehicle facing a white wall over five meters away; use a screwdriver to fine-tune until the beam's center point is slightly below the headlight height. The key is that the left headlight must be adjusted lower to avoid blinding others. I check the beam angle every time I change tires—no detail is too small for road safety.

[ArianaDella]

I've got some tips for adjusting Wuling's headlights. Besides aligning them against a wall, remember to turn off the engine and remove the key for safety. It's best to wear gloves during adjustment, as the plastic parts of the headlights become brittle in winter. If the screws won't budge, don't force them—spray some WD40 and try again. I always keep a tape measure in my car; measuring the beam height directly is more accurate when adjusting the lights. If the back seats are fully occupied, the headlights should be set lower to prevent them from turning into high beams when going uphill. The most useful trick is recording with a smartphone: first, walk around the car to film the beam positions before adjusting—it's much more reliable than judging by eye, and I've nailed it five times out of five.

[LeBrooke]

The Wuling Hongguang S headlight adjustment emphasizes practicality. From my experience, the most convenient time is at night in an underground parking lot. Estimate the distance to the wall based on the car's length—about three car lengths is sufficient. Setting the low beam height at around 30 cm is the safest, aligning it with the position of the front license plate. The key is to listen for the clicking sound of the screw turning; the Wuling's adjustment screw has a noticeable detent—stop when resistance increases. Don’t forget that wet roads reflect more glare, so the lights should be aimed slightly lower. I use the short-handle screwdriver that came with the engine oil purchase for adjustments—it fits easily into the engine bay without much effort.