···
Log in / Register

How soon should a new car be licensed?

1Answers
SanAmy
08/26/2025, 12:36:32 AM

It is recommended that a new car should be licensed within two months. The purchase tax for the car has a two-month deadline, and late fees will be charged if this period is exceeded. Only after paying the purchase tax can the car be licensed. After 60 days, a fine will be imposed, calculated as 0.05% of the purchase tax. Here are the relevant details: 1. The specific licensing process is as follows: Purchase insurance for the new car; pay the vehicle purchase tax; inspect the new car; submit required documents; conduct an inspection (except for exempt vehicles); select a license plate number; collect vehicle documents; pay the vehicle and vessel tax. 2. Buying a car out of state and licensing it locally: You need to submit a copy of your ID card, the car purchase invoice, the vehicle certificate, and a tax declaration to the local vehicle management office. After paying the purchase tax, you can proceed with licensing.

Was this review help?
118
Share
More Q&A

How Often Should Front and Rear Tires Be Replaced?

Car tires generally need to be replaced every 5 years or approximately 60,000 to 80,000 kilometers. If the tires are severely worn, they must be replaced earlier. In cases where the tires show no issues, if the mileage reaches 80,000 kilometers, replacement is necessary even if the tires haven't been in use for 5 years. Tires may also be considered for replacement under the following conditions: Degree of Wear: Check the tread pattern on the tire surface. If the tread depth is less than 1.6 mm or aligns with the wear limit indicator, the tires need replacement. Mileage: Generally, car tires should be replaced every 60,000 to 80,000 kilometers. Age: Tires older than 5 years age at an increasingly rapid rate. Even if the wear is not severe, replacement should still be considered.
106
Share

Should the windshield be replaced at a 4S shop or a repair shop?

Replacing the windshield at a 4S shop ensures quality, but you can also choose to pay out of pocket and have it replaced at a repair shop. For small cracks: Clean the crack with glass cleaner and alcohol; use a positioning sticker to align with the small hole and drip about 5 drops of repair solution; pull the syringe upward, secure the piston, and hold for about 10 minutes until bubbles completely escape; remove the syringe, reinsert it, and press downward to inject the repair fluid into the damaged area, holding for 15 minutes; remove the positioning sticker, apply the curing film, squeeze out the bubbles, let it sit for 20 minutes, and then peel off the curing film. For long cracks: Repairing long cracks is not recommended as the effect is quite limited. For such cracks, it is better to directly replace the entire windshield.
111
Share

How Often Should a Six-Year-Old Vehicle Undergo Annual Inspection?

Small private passenger vehicles require inspection every 2 years within the first 6 years, annually from 6 to 15 years, and every 6 months after 15 years. Below are the inspection cycle regulations for different vehicle types: Commercial Vehicles: Commercial passenger vehicles must be inspected annually within the first 5 years and every 6 months thereafter. Trucks: Trucks and large/medium-sized non-commercial passenger vehicles require annual inspection within the first 10 years and every 6 months thereafter. Compact Vehicles: Small and mini non-commercial passenger vehicles need biennial inspection within the first 6 years, with eligible vehicles only requiring inspection exemption decals. Starting November 20, 2020, 7-9 seat non-commercial mini/micro buses (excluding vans) were included in the exemption scope.
108
Share

What are the reasons for abnormal noise in the CFMoto 250sr engine?

The reasons for abnormal noise in the CFMoto 250sr engine are as follows: Excessive clearance between the piston and cylinder wall: Over-tight assembly of the piston pin or connecting rod bearing; excessive clearance between the tappet and its guide hole; wear of the cam profile; sometimes, the starting claw is loose, causing the pulley to make noise (more noticeable during speed changes). Excessive valve clearance: Excessive clearance between the tappet and its guide hole; wear of the cam profile; excessive clearance between the valve stem and its guide; broken valve spring; radial cracking of the camshaft timing gear; loose valve seat ring; valve sticking and unable to close. Excessive clearance between the piston and cylinder wall: Incorrect depth and width of the main bearing oil groove; low oil pressure leading to poor lubrication.
111
Share

Where is the problem when the four-wheel drive makes a clunking sound while turning?

The reasons for abnormal noises when a four-wheel-drive vehicle turns are as follows: Sounds coming from outside the vehicle: Lack of oil in the shock absorber's plain bearing: Open the hood and listen to see if the sound is coming from the top mount of the shock absorber. If the plain bearing of the shock absorber is making noise, you can apply some grease to the plain bearing. If the noise persists after greasing, it will need to be replaced. Loose stabilizer bar bushings: Check if the stabilizer bar bushings are loose or damaged. Loose or damaged stabilizer bar bushings will not only make noise when turning but also produce sounds when driving on uneven roads. Loose stabilizer bar bushings can be fixed by adding shims, but if they are damaged, they will need to be replaced.
103
Share

How many models are there in the BMW 1 Series?

BMW 1 Series includes the following models: 118i Fashion, 118i M Sport Package, 120i Leading M Sport Package, 120i Fashion, 120i M Sport Package, 125i Leading M Sport Package, 125i M Sport Package, etc. Here is the relevant introduction of BMW 1 Series: 1. Power: BMW 1 Series models are equipped with 1.5T and 2.0T engines, matched with a 7-speed dual-clutch transmission. 2. Exterior: The exterior design of the BMW 1 Series follows the family-style design, with the front grille adopting a double-kidney design, and the interior of the grille decorated with classic chrome trim. The headlights on both sides look very full, with obvious division inside the lamp group, high recognition, and good aggressiveness. The lower air intake adopts a trapezoidal design, with a grid-like interior and smoked treatment.
110
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.