···
Log in / Register

How is the Foton Wheat Harvester 2021 Model?

6Answers
AdelynAnn
07/29/2025, 05:14:48 AM

Foton Wheat Harvester 2021 Model offers high operational efficiency and superior performance. Here is a detailed introduction to the Foton Wheat Harvester 2021 Model: 1. High Operational Efficiency: Equipped with a 700mm widened bridge for smoother feeding, suitable for harvesting high-yield crops. The extended composite drum features low power consumption and strong threshing and separation capabilities. The patented upper air intake radiator dust cover reduces cleaning frequency and saves maintenance time. 2. Superior Performance: The 840mm widened cleaning chamber provides strong cleaning ability and high grain cleanliness. The double-layer reverse vibration sieve improves grain cleanliness by over 20% compared to traditional models.

Was this review help?
109
Share
DiLena
08/12/2025, 05:00:44 AM

I operated the Foton 2021 wheat harvester throughout the entire harvesting season, and its overall efficiency is indeed impressive. The 5 kg/s feeding capacity is more than sufficient for wheat fields in the North China Plain. The hydraulic system responds sensitively during turns, preventing any wheat stalk crushing. The grain tank elevator is 15% wider than the older model, reducing unloading time to under 90 seconds. Two points to note: with a 32 cm chassis ground clearance, you must slow down when crossing ditches to avoid scraping the drive shaft; after rainy days, it's best to install an anti-wrapping device to prevent the reel from getting clogged with straw. This model currently has high circulation in the used market—when purchasing, pay special attention to concave sieve wear and hydraulic oil cleanliness.

Was this review help?
9
Share
Expand All
JosieFitz
10/06/2025, 12:30:04 AM

As a veteran with ten years of experience operating harvesters, what impressed me most about the 2021 Foton model is its fuel consumption control. The Weichai 160-horsepower engine has a rated fuel consumption of 18 liters per hour, and actual full-load operation consumes around 22 liters, saving about 5 liters compared to some imported models. The dual-roller threshing mechanism is well-tuned, keeping grain breakage rates below 1.2%. However, the cabin insulation is average, so you'll need plenty of ice water for midday operations. If purchasing, I recommend opting for the straw shredder attachment—with strict environmental regulations nowadays, direct field return is both convenient and compliant. Remember to grease the steering linkage three times per season, otherwise the steering play will gradually increase.

Was this review help?
8
Share
Expand All
LeCatherine
11/19/2025, 12:57:35 AM

Last year, we purchased six units of this machine for the cooperative, and the harvesting data speaks volumes: the mean time between failures is 62 hours, with a maximum daily workload of 180 acres. The key advantage is the easy availability of spare parts, as most agricultural machinery shops in the county have them in stock. The driver's seat comes with vibration damping and ventilation, allowing for 10 hours of continuous operation without back pain. One thing to note is that the grain bin sensor tends to get clogged with wheat awns, so it's necessary to use an air gun to clean it after each workday. The chain case has slightly weaker sealing, so it's recommended to add a rubber strip for dust prevention. Compared to the newer models currently available, this generation may have a smaller smart screen, but its mechanical structure is more robust.

Was this review help?
3
Share
Expand All
DelSabrina
01/09/2026, 02:34:57 AM

Harvesting efficiency can be evaluated from three aspects: The operating speed of 8 acres per hour isn't the fastest, but the 0.8% header loss rate stands out. The hydraulic system's maximum pressure of 18MPa is sufficient for lodged wheat, though efficiency drops when oil temperature exceeds 85°C. After modifying the cooling fan speed, I managed to reduce summer operating temperatures by 6°C. The adjustable wheelbase design is highly practical—narrowing from 2.3m to 1.9m allows access to small plots. When purchasing, don't forget to inspect the ball joint pin on the cutterbar linkage, as this part wears quickly. The threshing concave clearance should be adjusted according to wheat moisture: 2 finger-widths for dry wheat, at least 3.5 for damp wheat.

Was this review help?
11
Share
Expand All
StellaRose
04/06/2026, 12:41:53 AM

Actual tests comparing the 2021 model with the latest version revealed significant maintenance cost advantages for this generation. The average price of engine maintenance parts is 40% cheaper than the new model, and two V-belts cost only 120 yuan. The properly spaced reel teeth design on the header rarely gets tangled with grass. The biggest surprise is the 2.5 cubic meter grain tank capacity, which is particularly suitable for slope operations - it won't spill grain even at a 35-degree tilt. It's recommended to install a grain tank baffle to prevent grain loss. Remember to replace the oil seal on the steering axle every two years - there have been several cases of steering pump failure due to sludge buildup. Overall, this machine is like an old ox - you can work it hard for five years without major repairs.

Was this review help?
18
Share
Expand All
More Q&A

What are the gear shifting techniques for manual transmission?

Manual transmission gear shifting techniques are as follows: 1. For manual transmission vehicles, the principle of "accelerate before upshifting, decelerate before downshifting" must be firmly remembered. Before upshifting, "rev" the throttle to increase the speed first; before downshifting, "release" the throttle to reduce the speed first. The clutch pedal must be fully depressed before shifting, and the gear lever operation should be light, quick, gentle, and precise. 2. Master the timing of gear shifting. Shift gears when the engine speed is around 2000 RPM. First reduce the throttle and then depress the clutch, so the clutch won't be forced to disengage, then shift gears. Skipping gears is not recommended. The downshifting sequence depends on the vehicle speed. Generally, downshift when the engine speed is below around 1500 RPM, based on your vehicle's condition. 3. The shifting action should be smooth. Depress the clutch fully in one motion, and engage the gear in one step. Familiarize yourself with the gear positions and practice the feel. If you encounter difficulty engaging a gear, shift to neutral, release the clutch briefly, then depress the clutch again to engage the gear. If the gear is not fully engaged, do not release the clutch, as this can easily wear out the transmission gears.
112
Share

How to Open the Trunk of a Volkswagen Polo?

Volkswagen Polo's trunk lid can be opened using the car key or from outside the vehicle. Here are the methods: 1. Using the key: Briefly press the trunk opening button on the remote key. The trunk must be opened within two minutes, otherwise it will automatically lock. 2. Manual method for opening the trunk lid: Press the upper part of the Volkswagen logo with your thumb to make the lower part of the logo pop out. Grip the lower part of the logo and open the trunk lid. Here is additional information: If the trunk lid is closed but not locked, it will automatically lock when the vehicle speed exceeds 7 km/h. After the vehicle comes to a stop, the trunk lid can be unlocked by opening the door or pressing the central locking unlock button on the driver's side door.
116
Share

What Causes the Abnormal Noise When Opening and Closing Car Doors?

Abnormal noises when opening and closing car doors mainly originate from wear and tear on the door hinges and limiters. Due to years of use, the door hinges and limiters may wear out or accumulate dust in the gaps, causing vibrations and resulting in abnormal sounds during door operation. Here is an introduction to car doors: 1. The door and the car body are connected via hinges, and it is normal for hinges to produce noise after prolonged use. To ensure the hinges remain smooth and quiet, apply lubricating oil every 2-3 months for maintenance. 2. Additionally, the door and the car body are connected by another component called the door limiter. To maintain it, open the door to its maximum angle, clean the grease and dirt from the limiter arm, pivot pin, and connecting bracket surfaces, and then apply an appropriate amount of grease to the upper and lower surfaces of the arm. 3. If the car has been in use for some time, check whether the door seals have aged. Since seals are made of rubber, they will gradually deteriorate and crack over time, leading to noticeable wind noise and friction sounds for passengers. If the seals are aged or damaged, it is recommended to replace them directly. Also, regularly clean dust and rainwater from the gaps between the seals during routine use to prevent aging.
119
Share

What Are the Causes of Radiator Leakage?

Possible causes of car radiator leakage include: hose rupture, oil emulsification, improperly secured radiator cap, rubber hose joint leakage, cooling tube rupture, and radiator cracking. Here is an introduction to car radiators: 1. The car radiator, also known as the heat exchanger, is a key component in the automotive cooling system. 2. Its function is to dissipate heat. The coolant absorbs heat in the water jacket, flows to the radiator to release the heat, then returns to the water jacket in a continuous cycle, achieving temperature regulation through heat dissipation. 3. The radiator is a crucial part of water-cooled engines, absorbing heat from the engine block to prevent overheating. Due to water's high specific heat capacity, its temperature doesn't rise significantly after absorbing engine heat. The engine's heat is transferred through the coolant circuit using water as a thermal conductor, then dissipated via large-area cooling fins through convection, maintaining the engine's optimal operating temperature.
111
Share

What is the difference between genuine parts and original parts?

Genuine parts refer to those produced by qualified manufacturers, while original parts are those produced by the automobile manufacturer itself or authorized professional parts manufacturers. The specific differences are as follows: 1. Genuine parts: Genuine parts refer to those produced by qualified manufacturers, which also fall under the category of aftermarket parts. The difference lies in the fact that genuine parts bear the manufacturer's name, brand, and production certification, etc., and are provided through formal channels. These manufacturers are included in the procurement list of automobile manufacturers, ensuring quality and after-sales service. In terms of craftsmanship and appearance, they are second only to original parts. 2. Original parts: Literally, original parts refer to those produced by the automobile manufacturer itself or authorized professional parts manufacturers. Regular original automobile parts are perfectly crafted, basically matching the quality of the original components without minor flaws, and their appearance and performance are consistent with the original components. They also come with professional certification and are stamped with the original part's logo and part number. Generally, original parts are mostly found in 4S stores, as they are specifically provided by automobile manufacturers for after-sales supply.
105
Share

How to Stay Awake During Long Drives?

Here are some methods to stay awake during long drives: 1. Take breaks: Long drives can be tiring due to the extended duration and distance. It's essential to take regular breaks at service areas. If you've been driving continuously for over 4 hours, it's advisable to rest for about 20 minutes. 2. Ventilate the car: Poor air circulation inside the car can reduce oxygen supply to the brain, leading to drowsiness. Opening the windows for fresh air can help you stay alert. 3. Listen to upbeat music: Playing energetic songs like rock, electronic, DJ, or rap can keep you excited and awake due to their rhythmic nature. 4. Chew gum or mint candies: Chewing gum keeps your mouth active, helping you stay focused and relaxed. For candies, opt for sugar-free mint varieties, as high sugar content can spike blood sugar levels and cause drowsiness. The cool flavor stimulates taste buds, aiding alertness. 5. Energy drinks: Many long-distance drivers carry energy drinks containing caffeine, like coffee or Red Bull. Some prefer tea, all of which have wakefulness-promoting effects. 6. Essential oils like 'Double Fly' or menthol balm: Applying these on the forehead or temples can stimulate and reduce fatigue. Be cautious not to apply too much and avoid contact with eyes due to their strong irritant properties, which can cause tearing and impair vision.
120
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.