···
Log in / Register

Has the Geely Xingrui trunk water leakage issue been resolved?

6Answers
VonBrandon
07/29/2025, 03:50:46 PM

Currently, no. There are generally two situations that can cause water leakage in the trunk. The first is leakage from the trunk sealing strip, which can be tested by spraying water—someone must spray water outside the trunk to identify the issue. The second, less likely scenario, is damage to the negative pressure port caused by water splashed from the tires into the trunk, which is relatively rare and requires careful inspection. Here is additional information: 1. Self-check for the cause of water leakage: You can identify leaks using a simple method by simulating rainwater flowing from the roof with a watering can to locate the leakage point. 2. Check common causes of leakage: Inspect whether there are issues with the tail light seals, leaks around the rear windshield rubber strip, cracked sealing strips, blocked drainage holes near the seals, or aging and cracked metal panels, among other potential problems.

Was this review help?
113
Share
DeFelicity
08/14/2025, 11:28:47 AM

I drive a Geely Xingrui myself, and the trunk once got water inside. After that rain, I opened it and saw water stains, which was quite frustrating. I checked and found cracks in the trunk lid's sealing strip, and water had seeped through the gaps. Later, I went to the 4S store and got a new sealing strip replaced for free. Now, after driving for over a year, there haven’t been any issues. However, I’ve heard from fellow car owners that it still happens with older models, so I think the newer versions might have improved the design, but it’s not 100% guaranteed to solve the problem for all cars. My advice is to carefully observe the water marks after rain. If you know about cars, you could temporarily patch the leak with waterproof tape, but it’s best to regularly check and maintain it. Overall, my experience is that as long as you fix it promptly, it’s not a big issue—just don’t delay too long, or rust on the chassis could become a bigger problem.

Was this review help?
14
Share
Expand All
LeKathryn
10/15/2025, 03:42:18 AM

As a mechanic who frequently works on Geely vehicles, trunk water leakage is not uncommon in the Geely Xingrui, mostly due to aging sealing strips or clogged drainage holes. Some owners report that Geely introduced upgrade kits after 2022, such as thickened rubber strips or optimized drainage paths, and the issue seems less frequent now. However, to thoroughly determine if the problem is resolved, I need to personally inspect the leak points, like conducting a water spray test or lifting the interior trim to check wire seals. If new parts haven't been replaced, cleaning the drainage holes yourself can provide temporary relief, but don’t ignore the risk of water accumulation corroding the frame. In short, contacting a 4S shop before taking action is more reliable, as they might have recall solutions. These minor issues can be resolved quickly, so there’s no need to worry too much about driving safety.

Was this review help?
15
Share
Expand All
HarperMarie
11/28/2025, 03:33:48 AM

As a Geely enthusiast, I've noticed the issue of water leakage in the Xingrui's trunk, which has been widely discussed online. Geely officially responded by enhancing the sealing design, such as using new waterproof materials in the 2023 model, with tests showing a reduced leakage rate. However, this hasn't resolved the issue for all vehicles. My suggestion is to check the production date or consult local dealers for any service notifications. Additionally, developing good habits like regularly cleaning the sealing strips to prevent drying and cracking, and avoiding parking in low-lying areas to prevent water accumulation, is advisable. Personally, I think Geely has responded quite proactively, taking swift action after owner feedback, but details may vary, so it's important not to be careless.

Was this review help?
8
Share
Expand All
JosiahLee
01/18/2026, 10:09:25 PM

Last time I washed my car, I found water in the corner of the trunk, which was caused by deformed sealing strips creating gaps for leakage. For a simple self-test: pour some water along the trunk lid seam to identify seepage spots for patching, or clean the sealing strips with a damp cloth to maintain elasticity. It's said that Geely has updated its parts inventory, with newer Xingrui models faring better but older models still occasionally experiencing this issue, so don't wait until problems arise to act. If frequent water ingress occurs, try adjusting your parking spot to avoid sun exposure and aging—it's not hard to handle, but the key is not to delay, prioritizing safety to prevent corrosion. It's advisable to keep some waterproof adhesive on hand for DIY fixes to save time and money, but for severe cases, consult a professional shop to check the drainage system.

Was this review help?
14
Share
Expand All
DelJuniper
04/14/2026, 11:28:58 PM

I prioritize car maintenance, and water ingress in the trunk of the Xingrui can lead to moldy odors or electrical failures, which is quite hazardous. Some owners have shared that Geely issued a service bulletin addressing this issue, mentioning an optimized rear lid structure, but it hasn't completely resolved all cases. My approach is to feel the bottom of the trunk before opening it on rainy days to check for dampness. If water is found, I promptly clear any blockages, such as using a hairdryer to dry it out and prevent mold. In the long run, regular inspections of the seals at the service center are essential to avoid prolonged water accumulation damaging the car body. Geely's response has been relatively timely, and it's important not to let minor issues escalate into safety hazards.

Was this review help?
9
Share
Expand All
More Q&A

What are the reasons for a car having a little electricity but not starting?

Car having a little electricity but not starting reasons are as follows: Is the battery charged: It may be due to power loss caused by reasons such as leaving the headlights on for a long time or the battery reaching the end of its lifespan. It is generally recommended to replace the battery every 2 years. Additionally, installing xenon headlights, high-power audio systems, DVD players, etc., can also cause vehicle circuit failures. Checking for no power in the vehicle is simple; just press the horn. Is there fuel: Pay attention to the quality of the fuel. Always refuel at reputable gas stations. When traveling, you can use a gauze to cover the fuel gun nozzle to filter out impurities. Wrong gear position: For automatic transmission cars, the gear must be in P (Park) or N (Neutral) when starting. If it is in R (Reverse) or D (Drive), the car will not start. Electronic failure: Mainly refers to the central computer control board losing functionality. Mechanical failure: Timing belt (chain) breakage, cylinder leakage causing no pressure, etc.
112
Share

What is the appropriate ignition timing angle?

6°--12°. Ignition advance angle: The crankshaft rotation angle from the ignition moment until the piston reaches the top dead center of compression. The ignition advance angle that enables the engine to achieve optimal power performance, fuel economy, and emissions is called the optimal ignition advance angle. Theoretically, the minimum ignition advance angle is 0 degrees, but to prevent igniting the air-fuel mixture during the power stroke (which would cause power loss), it is usually set above 5 degrees. This is also the angle required for starting speed. The maximum ignition advance angle should not be too large, generally not exceeding 60 degrees, otherwise vibration and temperature rise issues will become prominent, and efficiency will decrease. In reality, the rotational speed of the crankshaft structure is limited. 3. The most significant factors affecting the ignition advance are rotational speed and the combustion speed of the air-fuel mixture. As the speed increases, the time to rotate through the same angle shortens, requiring a larger advance angle to achieve the corresponding advance time. The combustion speed of the air-fuel mixture is related to the mixture's composition, engine structure, and other factors such as combustion chamber shape and compression ratio.
116
Share

What is the name of a three-wheeled motorcycle?

Piaggio MP3 or Bombardier. The Bombardier SPYDER, which many people may not have heard of, is a three-wheeled motorcycle manufactured by BRP, a famous Canadian yacht-building company. It has three wheels and is considered a luxury toy in China. Below is some relevant information: Power: Although it is a three-wheeled motorcycle, it provides the thrill of a heavy motorcycle. The three tires increase stability, and the design is unique and eye-catching, making it a standout on the streets. In terms of power: The Bombardier SPYDER is equipped with a 1000cc, 60-degree water-cooled engine from Bombardier, with a maximum power output of 130 horsepower and a top speed of 200 km/h. Additionally, it can accelerate from 0 to 100 km/h in under 5 seconds, showcasing its impressive performance. Handling: The unveiled BRP-Can-Am-Maverick-1000R side-by-side all-terrain vehicle is hailed as the new standard in high-performance off-road driving. It not only embodies the three core elements of BRP Can-Am—industry-leading performance, refined handling, and human-centered design—but also focuses on delivering a more authentic and intense Can-Am experience.
119
Share

How Many Turns of the Steering Wheel for a U-Turn?

The issue of making a U-turn in a car depends on the actual situation. Drive to the side position, remember not to press the accelerator at this time, you can brake and then give a little gas, then turn the steering wheel to the left until the U-turn is successfully completed. If you are making a U-turn in a place with many cars, please pay attention to whether there are vehicles coming from both sides of the U-turn. Be safe. Basic points to note for making a U-turn: At intersections with U-turn lights, proceed to the intersection. If there are special U-turn indicator lights or ground markings, follow the instructions of the indicator lights and ground markings. Sometimes there are restrictions under the signs, such as the words "U-turn on red," which means you can only make a U-turn when the light is red. At intersections without U-turn lights but with left-turn lights, generally speaking, as long as there is no prohibition of U-turn signs or separate U-turn indicator lights, motor vehicles can make a U-turn at any time without affecting normal traffic and ensuring safety. Usually, the central divider on general roads will change from a solid line to a dotted line near the intersection, and vehicles can make a U-turn in this area.
109
Share

What does the 175/70r14c tire mean?

Automobile tire 175/75/R14C indicates the specifications of the tire. Among them, 175 represents that the cross-sectional width of the automobile tire is 175mm; 75 represents that the aspect ratio of the tire is 75%; R represents that the tire has a radial structure; 14 represents that the applicable rim diameter of the tire is 14 inches; C indicates that the tire is a reinforced tire. Tire letters have special meanings: "X" indicates a high-pressure tire; "C" indicates a reinforced type; "B" indicates a bias-ply tire; "-" indicates a low-pressure tire. M and S are abbreviations for Mud and Snow in English, indicating that this type of tire is suitable for use on snowy, icy, and muddy roads. Additional information: Some tires have arrows or the word OUTERSIDE marked on the sidewall, indicating the rotation direction of the tire. If a small umbrella symbol is painted on the sidewall, it indicates that this type of tire is suitable for driving in rainy or slippery conditions. The DOT mark indicates that the tire has passed the certification of the U.S. and Canadian transportation departments. A 4-digit number usually follows the DOT mark, and unlike other text, it is not molded early but is pressed onto the tire later, such as (1805), which indicates the production date of the tire. 05 stands for 2005, and 18 stands for the 18th week.
104
Share

Should You Brake When Going Downhill?

It depends on the actual situation and urgency. Below are the relevant scenarios: If the goal is to control speed: Generally, there is no need to press the clutch; instead, you can utilize engine braking by releasing the accelerator to assist in deceleration, which helps reduce brake pad wear and lower the temperature of the braking system. Moreover, using engine braking is smoother than applying the brakes, making it less likely to cause skidding or loss of control. If it's an emergency situation: To stop the vehicle as quickly as possible, press both the clutch and brake pedals fully (at this point, the ABS anti-lock braking system will activate, and if equipped with a brake force distribution system, safety will be significantly improved). Simultaneously, grip the steering wheel firmly to avoid loss of control or rollover due to sudden steering movements.
120
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.