···
Log in / Register

Can I bring my phone into the Subject 3 exam?

1Answers
LiamLynn
08/30/2025, 01:36:16 AM

You can bring your phone during the Subject 3 exam, but it's best to turn it off to avoid affecting the test. Here are the relevant details: 1. Subject 3: It includes the road driving skills test and the safety and civilized driving knowledge test, which are part of the motor vehicle driver's license assessment. It is the abbreviated term for the road driving skills and safety and civilized driving knowledge test in the motor vehicle driver's examination. The content of the road driving skills test varies for different types of driving licenses. 2. Note: Starting from June 1, 2021, the interval between scheduling the Subject 3 exam has been adjusted from 30 days after passing the Subject 1 exam to 20 days. For those applying for an additional license for large and medium-sized passenger or truck driving, the interval between scheduling the Subject 3 exam has been adjusted from 40 days after passing the Subject 1 exam to 30 days.

Was this review help?
104
Share
More Q&A

Should You Use Internal or External Air Circulation When Sleeping in the Car?

When resting in the car with the air conditioning on during a parked sleep, it is essential to periodically switch to external air circulation or leave a small gap in the window. Continuous use of internal circulation can lead to carbon dioxide poisoning. Below is an introduction to internal circulation: 1. Internal circulation should be used when the outside air quality is poor, such as in cases of heavy vehicle exhaust or dust. 2. Another important function of internal circulation is to rapidly heat up or cool down the car. Here are the differences between internal and external circulation: 1. Internal circulation recirculates the air within the closed environment of the car, while external circulation brings outside air into the car. 2. The air intake for internal circulation is inside the car, preventing outside air from entering, whereas the air intake for external circulation is located below the front windshield wiper, drawing in outside air.
105
Share

What is the battery model of the Mazda 3 Axela?

The battery model for the Mazda 3 Axela is 55D26L. Below are the specific details about car batteries: 1. The battery's function is to store electrical energy. Without it, the car cannot operate normally. 2. Typically, household car batteries are 12V, with a no-load voltage around 13V and a load voltage not lower than 11V. If the voltage drops below this level, it can cause difficulty in starting. The battery can be charged by the alternator while the car is running. If the car is parked for an extended period, the battery may lose charge, making it difficult to start the car. Therefore, during long-term parking, it is advisable to start the vehicle at least once a week for more than 5 minutes to recharge the battery. 3. Generally, it takes 4-5 hours to fully charge a battery, and overcharging should be avoided.
111
Share

What Causes Car Engine Shaking During Ignition?

Here are the reasons for car engine shaking during ignition: 1. Severe engine carbon buildup. The most common cause of car shaking is a dirty throttle body or excessive carbon deposits in the fuel injectors. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold-start injector is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts and making ignition difficult. 2. Ignition system issues. Check the condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or weak spark plug firing can also cause this type of problem. The solution is to inspect whether the spark plugs have excessive carbon buildup and replace them if necessary. 3. Unstable fuel pressure. If you have already cleaned the engine carbon, throttle body, replaced the oil gasket and spark plugs, but still notice the car shaking at idle, it is recommended to visit a 4S shop to check the fuel supply pressure and the intake pressure sensor for any abnormalities. 4. Aging engine components. Car shaking can also be related to worn engine mounts. Engine mounts are responsible for absorbing minor vibrations during engine operation. If the engine mounts are faulty, these vibrations will be transmitted to the steering wheel and the cabin, causing shaking at idle.
105
Share

Should You Press the Clutch or Brake First When Parking a Manual Transmission Car?

Whether to press the clutch or brake first when parking a manual transmission car depends on different situations: 1. When the speed is relatively high, press the brake first and then the clutch; 2. When the speed is relatively low, you can press the clutch first and then the brake. The method for starting a manual transmission car is: 1. Turn on the ignition switch and start the engine; 2. Press the clutch pedal, shift the gear lever into 1st gear, and release the handbrake; 3. Slowly lift the clutch pedal and press the accelerator. A manual transmission car refers to a vehicle that uses a manual gear-shifting mechanical transmission to adjust the speed. It requires manually moving the gear lever to change the gear meshing position inside the transmission, thereby altering the gear ratio to achieve speed variation.
115
Share

What is the difference between the Mercedes-Benz G500 and G550?

Here are the specific differences between the Mercedes-Benz G550 and G500: 1. Production base: The G550 is produced in Canada, while the G500 is produced in Mexico. 2. Power: The G550 is equipped with a 5.5L V8 twin-turbocharged engine, delivering a maximum power of 400kW and a maximum torque of 760Nm, with a 0-100km/h acceleration time of 5.4 seconds. On the other hand, the G500 is equipped with a 4.0T V8 twin-turbo engine, producing a maximum power of 310kW and a maximum torque of 610Nm, with the maximum torque available from 2000 rpm to 4750 rpm. In terms of power, the G550 is slightly stronger.
120
Share

Should the positive or negative terminal of a car battery be connected first?

When connecting the car battery cables, the positive terminal should be connected first, followed by the negative terminal. Here are some precautions to keep in mind during battery installation and removal: 1. During installation, always connect the positive terminal first and then the negative terminal. If the positive terminal is disconnected first, any contact between the battery and the metal parts of the car body will directly connect the positive and negative terminals, resulting in a short circuit. 2. When removing or installing the battery, always disconnect the negative terminal first and reconnect it last. If the positive terminal is disconnected first, any contact between a metal wrench and the car body during the process can cause a short circuit. 3. The electrical system in vehicles operates on low voltage, direct current (DC), single-wire configuration, and negative grounding.
113
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.