Can a 1.6L Engine Vehicle Drive on Plateaus?

Can a C1 License Drive a 9-Seater Blue Plate Vehicle?

C1 license can drive a 9-seater blue plate vehicle. Here are additional details: 1. Vehicles with blue license plates: Generally, C1 license holders can drive small vehicles with blue license plates. 2. Manual or automatic 9-seater (including 9-seater) mini vans or commercial vehicles: Vehicles with more than 9 seats cannot be driven, even if they have blue plates. 3. C1 driving scope: There are significant restrictions on the number of passengers. First, it is stipulated that C1 license holders can only drive vehicles with 9 seats or fewer. Once the number of passengers exceeds 9, the vehicle falls into the category of medium-sized buses, which requires a B1 license to drive. There are also requirements for the vehicle's weight. The regulations clearly state that C1 license holders cannot drive vehicles with a total weight exceeding 4.5 tons.

13

4

Share

What is the difference between 5W-30 and 5W-40?

The differences between engine oils 5W-30 and 5W-40 can be divided into three main parts, as detailed below: 1. Different kinematic viscosity: (1) Engine oil 5W-30: The kinematic viscosity of 5W-30 at 100°C is 30, which is lower than that of 5W-40. (2) Engine oil 5W-40: The kinematic viscosity of 5W-40 at 100°C is 40, which is higher than that of 5W-30. 2. Different oxidation resistance: (1) Engine oil 5W-30: 5W-30 has poorer oxidation resistance compared to 5W-40, providing weaker protection for the engine during startup. (2) Engine oil 5W-40: 5W-40 has better oxidation resistance compared to 5W-30, providing stronger protection for the engine during startup. 3. Different detergency: (1) Engine oil 5W-30: 5W-30 is more effective than 5W-40 in inhibiting the formation of carbon deposits, varnish, and sludge or in removing these deposits. (2) Engine oil 5W-40: 5W-40 is less effective than 5W-30 in inhibiting the formation of carbon deposits, varnish, and sludge or in removing these deposits.

13

3

Share

Should You Shift to Neutral at Traffic Lights?

It is recommended to shift to neutral at traffic lights as this can reduce clutch wear. Here are some key points about neutral gear: 1. Definition: Neutral gear refers to the state where a vehicle's gearshift is not engaged in any forward or reverse gear, completely disconnecting the transmission from the drive wheels. For manual transmissions, neutral is the middle position, while for automatic transmissions it's marked with an "N". 2. Usage scenarios: Neutral can be used for towing, waiting at red lights, coasting (though coasting in neutral is not recommended for safety reasons). When driving, use neutral for gear changes or when parking, but always remember that coasting in neutral is dangerous and should be avoided for driving safety.

2

4

Share

What is the difference between BMW with GT and without GT?

BMW's GT series models are all crossover vehicles, and the body design of crossover vehicles is different from that of ordinary sedans and SUV models. Moreover, BMW's GT series models are relatively more expensive. BMW's GT series models include the 3 Series GT and the 6 Series GT. The 3 Series GT is a crossover vehicle based on the 3 Series. Below is the relevant introduction of the 3 Series GT: 1. Body dimensions: The length, width, and height of the 3 Series GT are 4852 mm, 1828 mm, and 1518 mm respectively, and the wheelbase of this car reaches 2920 mm. 2. Power: This car uses two engines in total, one is a low-power version of the 2.0-liter turbocharged engine, and the other is a high-power version of the 2.0-liter turbocharged engine. The low-power version of the 2.0-liter turbocharged engine has a maximum torque of 184 horsepower and 270 Nm, and can output maximum power at 5000 rpm, and can output maximum torque at 1350 to 4600 rpm. This engine is equipped with direct injection technology and uses an aluminum alloy cylinder head and block. The high-power version of the 2.0-liter turbocharged engine has a maximum torque of 252 horsepower and 350 Nm, and can output maximum power at 5200 rpm, and can output maximum torque at 1450 to 4800 rpm. This engine is equipped with direct injection technology and uses an aluminum alloy cylinder head and block.

5

0

Share

What Does Neutral Gear Mean?

Neutral gear refers to the state where the car's gearshift lever is not engaged in any forward or reverse gear, and the transmission is completely disengaged from the drive wheels. Below is a detailed introduction about the neutral gear in cars: 1. Overview: For manual transmissions, neutral gear means that the gears on the input shaft of the transmission are free-spinning on the shaft and cannot bear loads or transmit power. For automatic transmissions, it means that the degrees of freedom of the gear train are not restricted, so it also cannot transmit power. In terms of the power transmission route, the engine's power is transmitted to the transmission, but since there is no gear ratio inside the transmission, the power is interrupted, and the vehicle cannot start moving. 2. Precautions: The neutral position for manual transmission models is in the middle, while for automatic transmission models, it is marked with an "N". For driving safety, coasting in neutral is not recommended. Once the gearshift lever is placed in neutral for coasting, the drive wheels will lose driving force, and the connection between the engine and the drive wheels will be lost, causing the car to coast forward by its own inertia.

7

0

Share

What do IG1 and IG2 represent in automotive circuits?

The ignition switch has four positions: lock (off position), acc (radio position), on (ignition position), and start (starting position). Both IG1 and IG2 belong to the on position. Below are the relevant explanations: 1. After locking the car, the key will be in the lock state, which not only locks the steering wheel but also cuts off the power supply to the entire vehicle. 2. The acc state supplies power to some of the vehicle's electrical equipment, such as the CD player and air conditioning. 3. During normal driving, the key is in the on state, where all circuits in the vehicle are operational. 4. The start position is for engine starting, and after starting, it automatically returns to the normal state, which is the on position.

3

Share

Can a 1.6L Engine Vehicle Drive on Plateaus?

Can a C1 License Drive a 9-Seater Blue Plate Vehicle?

What is the difference between 5W-30 and 5W-40?

Should You Shift to Neutral at Traffic Lights?

What is the difference between BMW with GT and without GT?

What Does Neutral Gear Mean?

What do IG1 and IG2 represent in automotive circuits?

What brand of car is PORSCHE?

What is a Side Curtain Airbag?

What Are Paddle Shifters Used For?

What to Do When Abnormal Noises Occur While Driving?