Will Water Ingress Damage a Turbocharger?

1 Answers
LaStephen
07/29/25 11:34pm
This will not affect the supercharging system nor cause damage. Below is relevant information about turbocharged engines: 1. Introduction to Turbocharged Engines: A turbocharged engine refers to an engine equipped with a turbocharger. The turbocharger is essentially an air compressor that increases intake air volume by compressing air. It utilizes the inertial impulse of exhaust gases from the engine to drive the turbine in the turbine chamber, which in turn drives the coaxial impeller. The impeller then pressurizes the air delivered through the air filter pipeline, forcing it into the cylinders under increased pressure. 2. Function of Turbocharged Engines: The primary role of turbocharging is to enhance the engine's air intake volume via the turbocharger, thereby increasing the engine's output power and torque.
Was this review help?
5
3
Share
More Forum Discussions

Are Snow Tires Fuel-Consuming?

Snow tires are indeed fuel-consuming because their aspect ratio is different, and they have a larger contact area with the ground compared to regular tires, resulting in a higher friction coefficient. Since friction equals the friction coefficient multiplied by pressure, increased friction naturally leads to higher fuel consumption. Common misconceptions about snow tires are as follows: 1. New cars don't need snow tires: New tires and snow tires differ significantly in tread patterns and materials. Most high-quality snow tires remain flexible at temperatures as low as -20°C, whereas regular tires cannot achieve this. The tread design of snow tires is optimized for winter traction, and all-season tires, even with new treads, cannot replace snow tires in winter conditions. 2. Two-wheel-drive vehicles only need two snow tires: Most family cars are two-wheel-drive vehicles. If only two snow tires are installed on a two-wheel-drive car, starting the car may not pose a significant issue, but during braking, the difference in friction coefficients between the front and rear tires may cause the front wheels to stop while the rear wheels continue moving, leading to skidding or fishtailing, which can be more dangerous in certain situations. 3. Snow tires guarantee complete safety: Snow tires are not absolutely safe. When driving at high speeds, even with snow tires, braking distances will increase. Therefore, it is still essential to control your speed when driving on icy or snowy roads.
10
0
Share

Where is the Tire Pressure Monitoring Reset Button Located?

The tire pressure monitoring reset button is located on the control lever to the left of the steering wheel. Tire pressure reset is an operation performed on the tire pressure monitoring system after addressing tire pressure faults, aimed at resetting the system. Tire Pressure Reset Method: First, turn on the ignition switch, then press and hold the tire pressure monitoring reset button. Release the button upon hearing a beep sound. The tire pressure monitoring system will then store the current normal tire pressure data, automatically clear the previous data, and finally, the fault indicator on the dashboard will turn off, completing the tire pressure reset. There are generally three reasons for abnormal tire pressure: Abnormal Tire Pressure: The system typically alerts when the pressure is below 1.8 bar or above 3.0 bar. In such cases, tire inspection and pressure adjustment are necessary. Tire Pressure Monitoring Not Reset: After inflating the tires, if the tire pressure reset is not performed promptly, the system retains the old data, causing the tire pressure monitoring indicator to light up. A simple tire pressure reset will resolve this issue. Damaged Tire Pressure Sensor: The tire pressure sensor, installed inside the tire and connected to the tire inflation valve, monitors the tire pressure. If the sensor is damaged during driving, such as by hitting the tire, it can trigger the tire pressure fault light. In case of sensor damage, the only solution is to replace it with a new one.
19
2
Share

How to Replace the Battery in a Hyundai Mistra Key?

Modern Mistra key replacement battery specific tutorial is as follows: 1. Take out the spare mechanical key, then pry open the key shell along the gap. Once the shell is opened, you can see the key battery. Remove the old battery to replace it. 2. Precautions: After opening the key shell, be careful not to damage the chip. If the chip is damaged, you will need to reconfigure a new one. 3. Usage cycle: The car's remote key usually contains a battery, which can last for about 2 to 3 years. Once the battery is dead, the car owner needs to replace it in time.
19
1
Share

What are the symptoms of a bad starter motor?

If the starter motor malfunctions, the following signs may appear: 1. No response when starting the vehicle: This indicates that the starter motor is not working, and the issue could be with the power supply to the starter, or an open or short circuit inside the starter motor. 2. Dull sound and low RPM during startup: If the engine makes a dull sound and runs at a low RPM during startup, this problem is caused by an internal short circuit in the starter motor itself. Partial coil short-circuiting prevents it from generating sufficient rotational magnetic force, unable to provide the required torque for starting. 3. Motor operating sound is audible, but RPM is zero: This situation occurs when the starter motor's solenoid fails. The solenoid, a smaller cylindrical part on the starter, is responsible for pushing the starter gear into engagement with the flywheel. In this case, the starter motor keeps rotating but fails to drive the flywheel to start the vehicle. 4. Loud noise during startup: This is caused by damage to the starter motor's bearings, carbon brushes, or the surface of the starter gear, leading to operational issues. 5. Burning smell: A burning odor from the vehicle's chassis during startup indicates an internal short circuit in the starter motor, causing overheating of the starter wiring harness or coils.
12
5
Share

What is the ground clearance of the Mazda3 Axela?

The minimum ground clearance of the Mazda3 Axela is approximately 150mm. The minimum ground clearance under full load is around 115mm. Below is more information about the Mazda3 Axela: 1. The Mazda3 Axela is a vehicle produced by Changan Mazda Automobile. It is the third model featuring the new-generation 'Skyactiv' technology and the 'Kodo' design theme, making its debut at the 2014 Beijing Auto Show. 2. This model is equipped with an advanced human-machine interface that prioritizes driving safety and is the first to feature the 'MZD Connect' Mazda infotainment system. The vehicle's overall configuration consistently reflects a technologically advanced and user-friendly driving experience.
10
3
Share

Which country produces the EXEED car?

EXEED is a sub-brand of the domestic Chery Automobile, serving as a recent budget luxury car series. 1. EXEED primarily targets the mid-to-high-end and overseas markets, with its positioning above the Arrizo and Tiggo series. 2. The models are built on the M3X platform, incorporating the latest design language, Chery's newest powertrain, and the latest system developed by Chery and Baidu. EXEED is set to become a masterpiece for Chery's brand upgrade. 3. The EXEED-TX is positioned as a compact SUV, developed on the M3X platform, featuring a new design language called 'Life-in-motion'. It offers a 1.6T high/low power engine and a 1.5T hybrid system.
9
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.