Why is there no response when pressing the car key to unlock the vehicle?

3 Answers
GiselleRose
07/29/25 5:53pm
Reasons why the car key does not respond when pressing the unlock button: 1. The car key battery is dead and needs to be replaced. 2. It may be due to strong radio interference, preventing the vehicle from successfully receiving the key's signal. 3. Damaged components in the car key may cause it to malfunction. 4. The distance is too far for the vehicle to receive the signal. 5. The car battery may be dead. Steps to replace the car key battery are as follows: 1. First, remove the mechanical key to expose the gap in the plastic casing. 2. Use a tool to pry open the key cover once the gap is wide enough. 3. Note the orientation of the battery's positive and negative terminals and remember it before removing the old battery. The new battery must be installed in the same orientation. 4. Close the key cover, ensuring proper alignment to avoid damaging internal circuits during reassembly.
Was this review help?
5
0
Share
OBentley
08/14/25 9:40am
I've encountered car key failure several times and later summarized a few common causes. A dead coin battery in the key is the most frequent issue - simply opening it up and replacing it with a CR2032 battery solves the problem. Sometimes signal interference in the surroundings can also cause this, such as near high-voltage substations or parking lot signal jammers. I once couldn't unlock my car in an entire underground supermarket parking area due to this. If the spare key works, it's likely the original key's circuit board is damaged. Vehicle issues may also be responsible, like aging or water-damaged door receiver antenna wiring, or a faulty body control module. The simplest solution is to first use the mechanical key to open the door, then place the key close to the start button to attempt induction starting - many cars have this emergency induction feature.
Was this review help?
4
4
Share
Expand All
ReeseAnn
10/14/25 2:50am
From my experience, a malfunctioning car key requires systematic troubleshooting. First, determine whether it's a key issue or a car issue—testing with a spare key will point you in the right direction. A dead key battery is the simplest fix; just replace it yourself for about ten yuan. I've personally experienced interference issues, like at airport parking lots—sometimes moving to a different spot can resolve it. If multiple keys fail simultaneously, it's likely a vehicle-side fault. Check if the body control module got wet, especially after car washes or rain. The receiver antenna is usually near the rear windshield—inspect for rodent damage to the wiring. The easiest solution is visiting a dealership to read fault codes—their equipment can pinpoint exactly which module is faulty.
Was this review help?
13
2
Share
Expand All
More Forum Discussions

Which Material is Better for Spark Plugs?

Spark plugs made of precious metals are better. The spark plug is a crucial component in the ignition system of a gasoline engine. It introduces high-voltage electricity into the combustion chamber, causing it to jump across the electrode gap and generate a spark, thereby igniting the combustible air-fuel mixture in the cylinder. The spark plug mainly consists of a terminal nut, insulator, terminal stud, center electrode, side electrode, and shell. The main types of spark plugs include: standard spark plugs, extended insulator spark plugs, electrode-type spark plugs, seat-type spark plugs, pole-type spark plugs, and surface-gap spark plugs. Under high voltage, the air between the center electrode and the side electrode of the spark plug rapidly ionizes, forming positively charged ions and negatively charged free electrons. When the voltage between the electrodes reaches a certain level, the number of ions and electrons in the gas increases like an avalanche, causing the air to lose its insulating properties and forming a discharge channel in the gap, resulting in a "breakdown" phenomenon. At this point, the gas becomes a luminous body, known as a "spark." Along with the heat expansion, a "snapping" sound is produced. The temperature of this electric spark can reach 2000–3000°C, which is sufficient to ignite the air-fuel mixture in the cylinder's combustion chamber.
1
0
Share

What are the advantages of a Torsen differential?

Advantages are as follows: 1. Advantage one: The Torsen differential achieves constant and continuous torque control management. It operates continuously without any time delay, yet it does not interfere with the adjustment of total torque output, thus eliminating any torque loss. Compared to traction control and vehicle stability control systems, it offers greater superiority. Since it lacks the multi-plate clutches found in traditional self-locking differentials, there is no wear and tear, making it maintenance-free. The purely mechanical LSD boasts excellent reliability. 2. Advantage two: The Torsen differential can be matched with any transmission or transfer case and is compatible with other vehicle safety control systems such as ABS, TCS (Traction Control Systems), and SCS (Stability Control Systems). The Torsen differential is a purely mechanical structure that activates the moment a wheel begins to slip, featuring a linear locking characteristic. 3. Advantage three: The Torsen limited-slip differential is a fully automatic, purely mechanical limited-slip differential that is highly reliable, durable, and quick to respond. From certain perspectives, it represents a very balanced design. It can respond to torque differences between drive wheels in a very short time, adjusting torque output to address wheel differential issues. Moreover, its locking characteristic is highly linear and can be adjusted over a relatively wide torque range without being limited by the structural space of the differential housing, thus maximizing its effectiveness.
1
0
Share

What are the test contents for Subject 1, Subject 2, Subject 3, and Subject 4?

Subject 1, Subject 2, Subject 3, and Subject 4 have the following test contents: 1. Subject 1: Traffic regulations and related knowledge. Computer-based test with questions mainly in the form of cases, pictures, and animations. There are 100 questions in total, each worth 1 point. The question types include true/false, single-choice, and multiple-choice. 2. Subject 2: Field driving. On-site driving assessment includes reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving through curves (commonly known as S-curves). 3. Subject 3: Road driving. Assessment on highways or simulated roads includes preparation before driving, simulated light test, starting, driving straight, gear shifting operations, lane changing, pulling over, going straight through intersections, turning left at intersections, turning right at intersections, crossing pedestrian crossings, passing through school zones, passing through bus stops, meeting vehicles, overtaking, making U-turns, and night driving. 4. Subject 4: Safety and civilized driving knowledge. Computer-based test with questions mainly in the form of cases, pictures, and animations. There are 50 questions in total, each worth 2 points. The question types include true/false, single-choice, and multiple-choice.
2
4
Share

Can I Pick Up My Car the Same Day for Body Repair and Painting?

Body repair and painting involve complex procedures that are time-consuming, making it impossible to complete the entire process and allow for same-day pickup. If the vehicle has extensive damage, the time required will be even longer. Body repair and painting, commonly referred to as "bodywork and spray painting," are necessary when a vehicle has been in a collision, resulting in scratches or, more severely, deformations. Body repair involves reshaping and restoring the deformed areas of the vehicle, while painting restores the color and gloss to match the pre-collision condition. The workflow for body repair and painting is as follows: 1. Assessment: Before starting the repair, the technician evaluates the extent of the damage to determine the appropriate repair plan, as different levels of damage require different solutions. 2. Body Shaping: The deformed areas undergo cutting, grinding, stretching, heat treatment, and oxidation restoration. It's important to note that body repair not only aims to restore the vehicle's original appearance but also to maintain the metal's hardness as much as possible. 3. Filler Application: After body shaping, the technician applies filler to the body to sculpt the contours and adjust the smoothness. 4. Paint Application: The painting process is intricate, involving multiple steps such as primer coating, mid-coat application, color matching, topcoat spraying, and paint drying, all of which must be performed in a dust-free environment. 5. Paint Finishing: Even after painting, minor imperfections may remain. The technician then uses ultra-fine sandpaper or a polishing machine to refine the surface, restoring the vehicle's shine.
17
5
Share

What is the most effective method to remove odors from a new car?

Methods to remove odors from a new car are as follows: 1. Ventilation: Within the first six months of purchasing a new car or after adding decorations, develop the habit of driving with windows slightly open to maintain fresh air circulation inside the car. 2. High-temperature exposure: High temperatures can accelerate the release of harmful substances and odors. In summer, leaving all four car doors wide open under the sun can effectively eliminate odors. However, this method is only suitable for new cars. In older cars, formaldehyde has entered a 'latent phase,' and exposure to high temperatures may cause stable materials to release harmful substances again, potentially damaging the car's paint. 3. Choose reliable car accessories: Some low-quality manufacturers produce floor mats with excessively strong odors. Therefore, be cautious when selecting car accessories. Opt for fabric seat covers that do not require adhesives, and choose floor mats made from healthy TPE material, which is popular in Europe and America. 4. Pomelo peel deodorization: Clever car owners often place pomelo peels inside their cars, believing that more peels mean better formaldehyde removal. In reality, pomelo peels and vinegar rely on their own scents to mask odors, which can help eliminate smells but are ineffective in removing formaldehyde. 5. Activated carbon and photocatalysts: To remove formaldehyde from the car, activated carbon can be placed to absorb it, but a sufficient quantity is needed to be effective. Other high-cost methods include using photocatalysts and installing car air purifiers. Whether these methods are worth it is a matter of personal opinion.
6
4
Share

What are the components of a car's power supply system?

Automobile power supply system is mainly composed of battery, generator, and voltage regulator. The generator is responsible for charging the battery to keep it in a fully charged state for a long time. The battery and generator are responsible for supplying power to all electrical appliances in the vehicle. The following are relevant details: 1. Battery: It is an essential part of a car, which can be divided into traditional lead-acid batteries and maintenance-free batteries. Since the battery uses lead-calcium alloy as the grid frame, the amount of water decomposed during charging is small, and the evaporation of water is also low. In addition, the sealed structure of the shell releases very little sulfuric acid gas. Therefore, compared with traditional batteries, it has the advantages of not needing to add any liquid, easy connection to terminal posts, and long power storage time. 2. Automobile generator: It is the main power source of the car. Its function is to supply power to all electrical equipment (except the starter) and charge the battery when the engine is running normally (above idle speed). Based on the three-phase stator winding of an ordinary AC generator, the number of winding turns is increased and the wiring terminals are extended, and an additional three-phase bridge rectifier is added. At low speeds, the output is from the original winding and the additional winding in series, while at higher speeds, only the original three-phase winding outputs. 3. Voltage regulator: The generator is driven by the car's engine, and the engine speed is not constant, which will cause the generator output voltage to be unstable. Therefore, an electronic device is needed to control the generator so that the generator can output a relatively stable voltage at different engine speeds.
16
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.