Why Does the Tiggo 3 Consume More Fuel Over Time?

1 Answers
RicardoLynn
07/29/25 12:28pm
The main reasons why the Tiggo 3 consumes more fuel over time are: Engine Carbon Buildup: During long-term operation of the vehicle, gasoline inevitably produces carbon deposits and sludge during combustion. If these deposits and sludge are not cleaned in time, they will lead to increased fuel consumption. Spark Plug Failure: The function of a car's spark plug is to generate an electric spark with high voltage to ignite the air-fuel mixture. If the spark plug is damaged, it will reduce the ignition energy, causing uneven combustion of the mixture, which will result in slower acceleration and increased fuel consumption. At this point, it is necessary to promptly inspect and replace the spark plugs. Abnormal Tire Pressure: Abnormal tire pressure in a car can also affect fuel consumption. When the tire pressure is too low or the tread is severely worn, the contact area between the tire and the road surface increases, leading to greater friction, higher rolling resistance, and naturally higher fuel consumption. Conversely, excessively high tire pressure can have some fuel-saving effects, but this will reduce the ride comfort and pose a risk of tire blowouts. Therefore, drivers should also pay attention to whether the tire pressure is normal while driving.
Was this review help?
6
3
Share
More Forum Discussions

Will the vehicle misfire if the crankshaft bearing clearance is too large?

It is possible. The following are the effects of excessive crankshaft bearing clearance on engine performance: 1. Abnormal noise: Excessive clearance in the main bearings, caused by wear, can produce a "clanging" sound, accelerating wear on other main bearings and potentially damaging the crankshaft in severe cases; similarly, excessive clearance in the connecting rod bearings can also produce a "clanging" sound, accelerating wear on the piston pin and journal, reducing compression ratio, and causing excessive ignition advance angle, potentially damaging the cylinder liner in severe cases; 2. Bent or broken connecting rod: This can lead to decreased oil pressure, affecting lubrication in the upper parts of the cylinder head. The impact between the bearing and the shaft can, over time, produce a knocking sound, also known as bearing noise, which increases with engine speed. Severe wear of the bearings can cause the connecting rod to collide with the cylinder liner, resulting in a bent or broken connecting rod.
10
5
Share

What to Do If ID Card Is Lost During Driver's License Test?

If your ID card is lost during the driver's license test, you can apply for a temporary ID card. Here is the relevant information about losing your ID card during the driver's license test: 1. Temporary ID card: When applying for a temporary ID card, you need to bring your household registration booklet. Generally, after completing the driver's license test, you should promptly reapply for your ID card to avoid affecting normal use. 2. Driver's license test: The driver's license test is an examination to obtain a motor vehicle driver's license. The subjects of the driver's license test are uniform nationwide, and the driver's license test is divided into four subjects: theoretical knowledge, field driving skills, road driving skills, and civilized driving-related knowledge.
9
3
Share

How to Read the Car Temperature Gauge?

Car temperature gauges are typically marked with the letters "C" and "H" or use white and red zones to indicate different temperature ranges. The letter "C" stands for "cool," representing the cold end, while "H" stands for "hot," indicating the high-temperature end. Below is relevant information about the car temperature gauge: 1. Introduction: The temperature gauge measures the coolant temperature. After the engine warms up, a normal reading is usually between 70-90°C. If the coolant level in the radiator is low, the temperature will rise, and you may need to add water. If the gauge needle approaches the "H" or the red danger zone, or if the temperature warning light illuminates, it indicates that the engine coolant temperature is too high. 2. How the Temperature Gauge Works: The sensor for the temperature gauge is a thermistor-type sensor, which is threaded into the engine's coolant passage. The thermistor determines the amount of current flowing through the gauge's coil winding.
3
4
Share

Which dashed line should the alignment line be aligned with when reversing into the parking space?

The entrance of the parking space for reversing typically has two to three dashed lines. Trainees can use these dashed lines as reference points to stop the vehicle. When the vehicle is properly aligned and reversing, observe that the lower edge of the left rearview mirror just covers the dashed line at the entrance, then immediately press the brake and clutch to stop. Additional information: If there is only one dashed line in the middle, the best position for reversing into the parking space on either side is when the wheels, as seen from the rearview mirror, press the end part of the two protruding lines. If there are two dashed lines at the entrance, the best position for reversing is when the wheels, as seen from the rearview mirror, press the end of the middle dashed line.
5
0
Share

What Causes the Buick Excelle to Feel Sluggish and Muffled During Acceleration?

Buick Excelle feeling sluggish and muffled during acceleration is caused by carbon buildup, incompatible fuel, clogged filters, or engine malfunction. Carbon buildup includes deposits in the cylinders, throttle valve, spark plugs, and intake system. Fuel: Using fuel with an incompatible octane rating can reduce the vehicle's power output. Air intake: If the air filter is not cleaned regularly, it can become clogged over time. Engine overheating: Insufficient engine oil, insufficient engine coolant, or malfunctioning engine cooling components. Solutions for the Buick Excelle feeling sluggish and muffled during acceleration are as follows: Visit a 4S dealership for carbon cleaning services, but the approach should be tailored to the specific situation. Use the appropriate fuel grade for your engine as specified, and perform regular maintenance. Clean the air filter regularly. Regularly check the oil and coolant levels. Do not mix different types of engine oil or use water as a substitute for coolant. Perform regular maintenance.
1
5
Share

Is Lexus a German or Japanese car?

Lexus is a Japanese car brand. Lexus, also known as Lexus, is a renowned luxury automobile brand under the Japanese Toyota Group. Its logo features the uppercase letter 'L' from the name Lexus, enclosed within an ellipse. The main models under the Lexus brand include the LM, UX300e, ES, RX, NX, UX, and CT. Taking the ES as an example, its dimensions are 4900mm in length, 1820mm in width, and 1450mm in height, with a wheelbase of 2820mm. The front seats' backrests have been redesigned to effectively increase rear passenger knee room by 71mm and legroom by 104mm, enhancing comfort. The optimized 10-way power-adjustable front seats come with lumbar support, effectively reducing driving fatigue.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.