Why does the car feel sluggish when starting after changing the transmission oil?

How to deal with small dots after car painting?

First, perform a simple polishing on the car body surface. Paint oxidation renewal polishing and paint scratch repair operations are mostly carried out locally. Squeeze an appropriate amount of wax liquid onto the car body. Then use a polishing machine with the wax liquid for polishing. The film formed by waxing can reflect part of the light, effectively preventing the car paint from aging. Next, wipe the car body with a towel to make the polished part smoother and cleaner. Finally, you can see that the car's paint surface is restored to its original condition.

8

4

Share

What is the size of the Prado wiper blades?

Toyota Prado wiper blades for all models are uniformly sized at 650mm/500mm. Here is the relevant information: The Toyota Prado wiper blades are typically fixed with a U-hook type mechanism, and the blades can be removed simply by pulling up the hook. After replacing the wiper blades, wet the windshield and set the wiper switch to various speed positions to check if the wipers maintain a consistent speed at different settings. Also, inspect the wiping performance and whether the wiper arms exhibit uneven swinging or missed spots. Below are the steps for replacing the wiper blades: 1. Push the wiper arm in the direction of the car's front until it locks into a specific position. Press the wiper blade's release button while gently shaking and pulling the blade upward to remove the old rubber strip. (Note: Do not let the wiper arm snap back onto the windshield, as this may cause glass damage or scratches. Placing a towel on the glass can help prevent scratches.) 2. Release the two clips and carefully pull out the old rubber strip. (Be gentle when releasing the clips and the middle connecting mechanism. Do not use excessive force, and avoid removing the plastic covers at both ends.) 3. When installing the new rubber strip, ensure the two metal pieces are staggered and correctly placed into the first groove. This process requires patience; install one side first, then the other. 4. Once successfully installed, reverse the removal steps to reattach the wiper arm to its original position.

15

2

Share

How Many Times Can a Driving Test Appointment Be Canceled?

You can cancel a driving test appointment up to 3 times. Below is relevant information about the motor vehicle driving test: 1. Test Content: The motor vehicle driver's test consists of three parts: the traffic laws and regulations knowledge test, the field driving skills test, and the road driving skills and safe driving common sense test. 2. Retakes: Each test can be taken once, and those who fail can retake it once. If you do not take the retest or fail the retest, the current test session ends, and the applicant must reschedule the test. However, the retest for the field driving skills test (Subject 2) and the road driving skills test (Subject 3) must be scheduled at least 10 days later. If you fail the safe driving common sense test (Subject 3), your passing score for the road driving skills test remains valid.

6

3

Share

How to adjust the handbrake of Haima M5?

Use a jack to lift the rear of the car so that the two rear wheels can rotate. Adjust the car's gear. If it's an automatic transmission, shift to P gear; if it's a manual transmission, shift to 1st or 2nd gear. Adjust the handbrake to an appropriate tightness. If it's too tight, the screws may not turn; if it's too loose, parts inside the handbrake may block the view of the screws. After adjustment, fully release the handbrake and check if the rear wheels can rotate. Both rear wheels should be checked to prevent wheel lock.

18

0

Share

What to Do When There Are Too Many Cars to Overtake in Subject 3?

Turn on the left turn signal, observe the left rearview mirror, and note that during the exam, there must be an obvious head-turning action. After the left turn signal has been on for three seconds, observe the left rearview mirror again to confirm there is no traffic behind, then accelerate and change lanes. Once the lane change is completed, immediately turn on the right turn signal and observe the right rearview mirror. As above, there must be an obvious head-turning action. After the right turn signal has been on for three seconds, observe the right rearview mirror again to confirm there is no traffic, then change lanes back to your original lane. This completes the overtaking maneuver.

13

2

Share

How to Register an Out-of-Town Used Car with Local License Plates?

First, confirm whether the local vehicle management office accepts the model you intend to purchase. For example, some cities do not accept vehicles that are too old or carburetor-equipped vehicles. When purchasing the used car at the buying location, it is usually required that the seller handles the file transfer. During the file transfer process, you must provide the identity proof of the new owner who will register the vehicle. After returning, submit the files to the local vehicle management office for review. Once the review is passed, you can begin the registration process. After obtaining the new license plates, use the new vehicle registration certificate, transaction invoice, and relevant transfer documents to complete the transfer of the purchase tax at the purchase tax management office.

11

4

Share

Why does the car feel sluggish when starting after changing the transmission oil?

How to deal with small dots after car painting?

What is the size of the Prado wiper blades?

How Many Times Can a Driving Test Appointment Be Canceled?

How to adjust the handbrake of Haima M5?

What to Do When There Are Too Many Cars to Overtake in Subject 3?

How to Register an Out-of-Town Used Car with Local License Plates?

Tips for Answering Questions in Driving Test Subject 1

Which country is the Wuling brand from?

How to deal with excessive fuel consumption in a 2012 Magotan?

What to Do When the Seat Belt Height Adjustment is Damaged?