Why can't the electric vehicle charger charge after being exposed to rain?

1 Answers
DelGideon
07/30/25 8:23am
There are many reasons why an electric vehicle cannot charge after being exposed to rain. First, it's necessary to analyze the cause, which could be an issue with the charger, the battery, the wiring, or the controller. For example, the battery might be charging, but if the controller is damaged, the vehicle won't start. The reasons are as follows: 1. The electric vehicle battery has reached the end of its lifespan: Most electric vehicles use lead-acid batteries as their power source, and the typical lifespan of a lead-acid battery is around 3 years. When the battery's lifespan expires, it may fail to charge. 2. Poor contact: The most common issue is poor contact between the fuse tube and the fuse holder, which can result in the battery not charging or not charging fully. 3. Blown fuse or open circuit: In an electric vehicle battery, the circuit breaker plays a crucial role, and the fuse, as an important component of the circuit breaker, is equally vital. If the fuse inside the battery blows, the battery will not receive power.
Was this review help?
19
4
Share
More Forum Discussions

What Causes Rough Shifting in Automatic Transmissions?

Rough shifting in automatic transmissions is typically caused by insufficient transmission fluid or when the fluid has reached its replacement interval, necessitating an inspection of the transmission fluid. Additional relevant information is as follows: 1. Transmission Fluid: Transmission fluid is a lubricant that maintains the cleanliness of the gear system, ensuring the proper operation of the vehicle's transmission and appropriately extending the service life of the transmission components. 2. Types: Transmission fluid is divided into two types: automatic transmission fluid and manual transmission fluid. Different transmission brands require specific types of fluid, and transmission fluids should not be mixed.
3
0
Share

What engine is equipped in the Changan Eado DT?

Changan Eado DT offers models with either a 1.0T turbocharged engine or a 1.6L naturally aspirated engine. Introduction to the Changan Eado DT: 1. Body dimensions: The length, width, and height are 4575/1750/1500mm respectively, with a wheelbase of 2610mm. 2. Exterior design: It features the currently popular X-shaped front grille, paired with exquisite horizontal chrome strips, sharp headlight clusters, and LED daytime running light strips, giving the vehicle a particularly noticeable stylish appeal. 3. Configuration: It comes equipped with features such as a sunroof and shark fin antenna.
20
0
Share

What are the symptoms of a broken transmission mount pad?

When starting the car, there will be shaking, and during driving, the stability of the car will be reduced. More relevant information is as follows: 1. If the transmission mount pad is damaged, it needs to be replaced immediately. If the transmission mount completely breaks during driving, the support force of the transmission will lose balance. 2. Whether it is an automatic transmission model or a manual transmission model, the transmission will cause abnormal gear shifting during operation. After the transmission mount is damaged, it will also cause jerking during the transmission's operation. The reason for this phenomenon is that the temperature of the transmission oil is too high, and impurities appear inside the transmission oil, causing jerking during the transmission's operation.
9
3
Share

Solution for Great Wall B183C00 Fault Code

PDU relay or feedback circuit malfunction. Below are the relevant details: 1. Cause: While controlling various relays (ACC relay, IG1 relay, IG2 relay, and CRANK relay), PEPS monitors their engagement status. When PEPS detects that the relay status doesn't match the required power mode status, it stores fault code B183C00. 2. Solution: Connect a fault diagnostic tool, access the PEPS control unit, read the status data stream of ACC relay, IG1 relay, IG2 relay, and CRANK relay, and check whether each relay can properly switch between engagement and disengagement under various power modes.
3
4
Share

How to Switch Between High Beam and Low Beam?

When the switch is turned to the low beam position, pulling the lever inward will flash the high beam once, while pushing it outward will keep the high beam on continuously. During driving, you should immediately switch from high beam to low beam in the following situations: 1. When there is an oncoming vehicle; 2. When you are close to the vehicle in front traveling in the same direction; 3. When the road is already sufficiently illuminated. Additional relevant information is as follows: Car headlights include high beam and low beam, both of which are used to illuminate the road ahead of the vehicle. The difference is that one illuminates a shorter distance while the other illuminates a longer distance.
3
3
Share

What is the function of the vacuum pump on a BMW?

Vacuum pump is used to generate negative pressure to enhance the vehicle's braking force, which is part of the vehicle's braking system and provides auxiliary assistance to it. The vacuum pump needs to be connected to the vacuum tube, also known as the brake oil pipe, to transmit the generated pressure and thus provide assistance. Here is some related information: The vacuum pump is a German automotive brand, a luxury car brand. The BMW brand, abbreviated as BMW, was established in March 1916. The brand's predecessor was an aircraft factory, and it later began manufacturing cars. The brand has multiple models, and BMW vehicles are known for their excellent handling. They have a very large market presence, and their kidney-shaped grille is very iconic.
15
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.