Where is the wiper fuse located on the Besturn X80?

1 Answers
VonGarrett
07/29/25 3:07pm
The wiper fuse of the Besturn X80 is located under the dashboard on the driver's side. Detailed explanation of the Besturn X80 wiper fuse: Under the dashboard on the driver's side, there is a long narrow cover. When facing the fuse box directly, the fuse in the lower right corner is the wiper fuse (or you can check the insurance instructions printed on the inside of the cover). Wiper: It is a tool installed on the front windshield of motor vehicles to simply clean rainwater and other debris that may obstruct the driver's view. The wiper assembly includes a motor, reducer, four-bar linkage, wiper arm spindle, and wiper blade assembly. When the driver presses the wiper switch, the motor starts. The motor's speed is increased in torque and reduced in speed through the worm gear mechanism, which drives the rocker arm. The rocker arm then drives the four-bar linkage, which causes the shaft mounted on the front panel to swing left and right. Finally, the shaft drives the wiper blade to sweep across the windshield.
Was this review help?
16
3
Share
More Forum Discussions

Can You Continue Driving with a DPF Regeneration Fault?

You can continue driving with a DPF regeneration fault. Here are the precautions for DPF usage: 1. Fuel requirements for the DPF post-processor: It is necessary to use low-sulfur diesel that meets China V emission regulations (sulfur content less than 10ppm) to prevent poisoning and clogging of the post-processor. Additionally, to extend the cleaning interval of the post-processor, it is recommended to use CJ-4 grade or higher engine oil. The ash content in the lubricating oil can significantly affect the DPF, as high ash content can easily cause DPF clogging. 2. Conditions for triggering DPF regeneration: Regeneration is triggered by carbon loading, which is calculated through the ECU's internal data model. When the carbon load is between 18g and 30g, active regeneration is used, where the engine operates normally, the exhaust treatment system outlet temperature is higher than the normal range, and the high exhaust temperature light remains on. When the carbon load is between 30g and 40g, driver-initiated regeneration is used, meaning manual regeneration by the driver.
12
5
Share

Is the Sagitar an international model?

The Sagitar is an international model, known as the Jetta in overseas markets. The Sagitar is a compact car under the FAW-Volkswagen brand, with a body length of 4544mm, width of 1760mm, and height of 1461mm. The Sagitar offers good fuel efficiency, with a combined fuel consumption of 8L per 100km, and is equipped with three engine options: 1.4TSI, 1.8TSI, and a 1.6L naturally aspirated engine. The front fascia of the Sagitar maintains the distinctive style of the Volkswagen brand, featuring sharp-angled headlights and a wide front bumper that add a youthful and dynamic appeal. Two design lines originating from the inner edges of the headlights traverse the entire front hood up to the A-pillar, forming a perfect angular shape with the front grille, bringing vitality to the otherwise plain and lifeless front hood.
12
4
Share

How to Adjust Valves on a Three-Cylinder Engine?

To adjust the valves on a three-cylinder engine, follow these steps: 1. Open the valve cover and prepare the necessary tools for turning the engine. The engine nameplate usually indicates the standard valve clearance. Locate the two corresponding valves for the engine. 2. Identify the position of the engine valves. To adjust the first cylinder, rotate it to the top dead center (TDC) position, where the valves are in a free state, allowing both intake and exhaust valves to be adjusted. 3. Use the engine turning tool to rotate the engine to the TDC of the first cylinder. When you observe clearance in both the intake and exhaust valves during rotation, you can adjust the valve clearance of the first cylinder. Loosen the lock nut of the first cylinder's intake valve, place the appropriate feeler gauge between the valve and the rocker arm, adjust to the specified clearance, and then tighten the lock nut. 5. Adjust the other two cylinders (second and third) using the same method. After adjusting all three cylinders three times, the process is complete.
7
0
Share

What is the Difference Between 48v and 60v?

The differences between 48v and 60v are price, configuration, power, speed, and load capacity. Price Difference: 48v electric vehicles are generally cheaper, while 60v electric vehicles are more expensive, but both can meet commuting needs. Configuration Difference: A 48v electric vehicle's battery pack typically consists of four 12v batteries connected in series, whereas a 60v model uses five. The accompanying motor, controller, tires, brakes, etc., also differ, with 60v models generally offering higher-end configurations. Power Difference: Generally, a 48v electric vehicle uses a 350W motor, while a 60v model often features higher-powered motors, such as 600W or 800W. Speed and Load Capacity Difference: 60v electric vehicles usually have higher speeds than 48v models, and their load capacities differ accordingly. For frequent uphill travel, 60v electric vehicles provide stronger kinetic performance.
6
3
Share

Does exposing a car to direct sunlight have any effects?

Exposing a car to direct sunlight does have effects. The consequences of leaving a car in a high-temperature environment under the sun are as follows: 1. Prolonged exposure to sunlight can cause the car's paint to fade. 2. Extended exposure to sunlight can accelerate the aging of plastic components such as tires, windshield wipers, and the dashboard. 3. Excessive heat from sun exposure can raise the interior temperature to dangerous levels, potentially causing heatstroke for anyone inside the car, which can be life-threatening. Methods for car maintenance: 1. When washing the car, it's important to clean the interior leather periodically to prevent bacterial growth on the leather seats. 2. Wipe the car with clean water once a week; there's no need to visit a car wash frequently. 3. Regularly place some activated charcoal inside the car, as vehicles emit a lot of exhaust during use, and some residue may inevitably remain inside the car.
20
3
Share

Can People with Red-Green Color Weakness Renew Their Driver's License?

People with red-green color weakness cannot renew their driver's license. Below are the specific materials required for renewing a motor vehicle driver's license: 1. "Motor Vehicle Driver's License Application Form": Must be signed by the applicant; the motor vehicle driver's license and the owner's relevant documents. 2. Proof of identity of the motor vehicle driver: If the applicant cannot be present, a jointly signed application form by the applicant and the agent, as well as proof of identity (original and copy) of both the applicant and the agent, must be submitted. 3. Proof of physical condition: A medical certificate issued by a county-level or higher medical institution or a military medical institution at the regimental level or above. For those applying to drive small automatic transmission passenger vehicles for the disabled, a medical certificate issued by a specialized medical institution designated by the provincial health authority must be submitted. 4. Three photos of the motor vehicle driver: The photos must be straight-edged, front-facing, color passport-style photos taken within six months before applying for the driver's license, with a white background and no uniform clothing.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.