Where is the USB port in the Mercedes-Benz GLC260?

2 Answers
DelAutumn
08/29/25 5:04am
Mercedes-Benz GLC260 USB ports are located in: 1. Inside the center armrest; 2. Near the rear air conditioning vents. Taking the 2021 Mercedes-Benz GLC260 as an example, it belongs to the mid-size SUV category with the following dimensions: length 4764mm, width 1898mm, height 1642mm, wheelbase 2973mm, front track 1614mm, rear track 1611mm, and a fuel tank capacity of 66 liters. The 2021 Mercedes-Benz GLC260 is equipped with a 2.0T turbocharged engine producing maximum power of 197PS (145kW) and peak torque of 320Nm, paired with a 9-speed automatic transmission.
Was this review help?
4
0
Share
DiSavannah
09/11/25 2:49am
I've been driving this Mercedes-Benz GLC 260 for over three years and I'm very familiar with the USB port locations. There's a small storage compartment in front of the center console - when you open the lid, you'll find a Type-A USB port which I frequently use for charging my phone. There's another USB port inside the center armrest that I use for playing music from a flash drive. The positions are ergonomically designed - you can easily reach them while driving without distracting your attention. Always use original charging cables, otherwise you might experience slow or unstable charging. In summary, finding the ports is easy, but avoid operating them while driving to prevent distraction. Regular cleaning of the connectors can also prevent poor contact issues.
Was this review help?
3
2
Share
Expand All
More Forum Discussions

How to Check Vehicle Driving Route with Car Positioning?

To check a vehicle's driving route through positioning, you can install a GPS tracker. Here are the detailed components of a GPS tracking system: 1. Space Segment: Consists of 24 satellites. These orbit at 20,200 km above the Earth's surface with a 12-hour orbital period. 2. Ground Control System: Composed of monitoring stations, a master control station, and ground antennas. 3. User Equipment: The GPS receiver. Its primary function is to capture selected satellites based on a specific elevation angle and track their movements.
19
2
Share

How to Determine if an Oxygen Sensor Has Failed?

Methods to determine if an oxygen sensor has failed include: 1. Decreased engine power, increased fuel consumption, and unstable idle operation; 2. Excessive carbon content. The testing methods for an oxygen sensor are: 1. Unplug the oxygen sensor connector; 2. Use a multimeter in resistance mode to measure the resistance between pins 1 and 2 of the sensor; 3. A resistance value between 4 and 40 is normal—if the resistance is abnormal, the oxygen sensor should be replaced. The working principle of an oxygen sensor is: It uses a ceramic sensing element to measure the oxygen potential in a heating furnace or exhaust pipe, calculates the corresponding oxygen concentration based on the chemical equilibrium principle, and monitors and controls the air-fuel ratio during combustion to ensure product quality and compliance with exhaust emission standards.
12
5
Share

How to Turn Off the Fog Lights on a Teana?

The fog light switch for the Teana is located on the light control lever to the left of the steering wheel. Simply twist it to turn off the fog lights. Below is an introduction to fog lights: 1. The purpose of fog lights is to make the vehicle visible to others in foggy or rainy conditions where visibility is significantly affected by the weather. Therefore, fog lights need to have a light source with strong penetration. Most vehicles use halogen fog lights, while LED fog lights are considered more advanced. 2. Fog lights can be removed, but the removal process is relatively complex. The steps for removing fog lights are as follows: (1) Use a flathead screwdriver to gently pry from the back of the fog light grille to release the clips holding it in place. This will create a larger gap at the front. Then, carefully use the screwdriver to pry the clips securing the grille to the front bumper one by one. Once all clips are released, the fog light grille can be removed. Be sure to proceed slowly and gently to avoid breaking the plastic clips. (2) You will now see the fog light fixed to the front bumper. Upon closer inspection, you will notice that the fog light is secured by two screws. Use a T-25 spline tool to remove these screws, and keep them safe for reinstallation later. (3) After removing the screws, the fog light is held in place by two tabs inserted into the bumper's clip holes. Hold the side where the screws were removed and gently pull upward to detach the fog light.
16
0
Share

Where is the fuel pump fuse of Lavida?

Lavida's fuel pump fuse is located in the box on the lower left side of the steering wheel. When replacing a new fuse, pay attention to the fact that the rated current and size of the fuse must be exactly the same as the original one. Taking the 2019 Lavida as an example, it belongs to the compact car category, with a body size of 4613mm in length, 1765mm in width, and 1460mm in height, a wheelbase of 2610mm, and a curb weight of 1210kg. The 2019 Lavida features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 112PS, a maximum power of 82kW, and a maximum torque of 145Nm, paired with a 5-speed manual transmission.
6
4
Share

What are the differences between Toyota Avalon and Toyota Camry?

The differences between Toyota Avalon and Toyota Camry are: 1. Different platforms: Toyota Avalon is under FAW Toyota; Toyota Camry is under GAC Toyota. 2. Different body dimensions: Toyota Avalon has a length, width, and height of 4978mm, 1849mm, and 1435mm respectively, with a wheelbase of 2870mm; Toyota Camry has a length, width, and height of 4885mm, 1840mm, and 1455mm respectively, with a wheelbase of 2825mm. Both Toyota Avalon and Toyota Camry are four-door, five-seater sedans, with front suspension types being MacPherson independent suspension and rear suspension types being E-type multi-link independent suspension.
7
0
Share

What kind of four-wheel drive does the Highlander belong to?

The Highlander belongs to the on-demand four-wheel drive system. On-demand four-wheel drive means that the four-wheel drive is only activated when necessary, while remaining a two-wheel drive system under other conditions. Taking the 2020 Highlander as an example, its body dimensions are: length 4890mm, width 1925mm, height 1715mm, with a wheelbase of 2790mm and a fuel tank capacity of 72.5 liters. The 2020 Highlander features a MacPherson strut independent front suspension and an E-type multi-link independent rear suspension. It is equipped with a 2.0L turbocharged engine, delivering a maximum horsepower of 220 PS, a maximum power of 165 kW, and a maximum torque of 350 Nm, paired with a 6-speed automatic transmission.
8
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.