Where is the USB port in the 2012 Sylphy?

2 Answers
AylaDella
07/25/25 8:03am
The USB port of the Nissan Sylphy is located in front of the gear shift lever. The Sylphy has only one USB port. If you need to install a dash cam, rearview camera, etc., you need to connect directly to the cigarette lighter. The USB port provides external playback devices with USB, AUX, and SD card slots. Below is the relevant introduction: 1. Design: The Sylphy adopts the brand's new V-Motion 2.0 design language; benefiting from Nissan's global CMF platform with a longer and wider chassis structure. It features a 1.254 luxury car width-to-height ratio, achieving an ultra-low drag coefficient of 0.26Cd, along with a 1.5Gpa UHSS high-rigidity body structure, ensuring greater driving safety. 2. Configuration: The all-new 3rd generation HR16 intelligent engine, with four cutting-edge technologies, works in synergy with the intelligent active grille, reducing the Sylphy's combined fuel consumption to 4.9L per 100km. In addition to the significantly enhanced body structure, the Sylphy is also equipped with Nissan's exclusive IDM Intelligent Driving Management system.
Was this review help?
17
1
Share
StAdriana
08/10/25 6:45pm
I've been driving a 2012 Nissan Sylphy for several years, and the USB port is usually hidden inside the center armrest. Just lift the armrest lid, and you'll see the small USB port alongside the AUX jack. When I bought the car, the salesperson mentioned that it was designed this way to prevent exposed wiring. I often use it to charge my phone or plug in a USB drive for music—it's quite practical. If the connection gets loose, gently adjusting the phone or cleaning the port usually does the trick. The port can occasionally act up in an older car, but regular checks help avoid major issues. The Sylphy's spacious interior and conveniently placed port don't interfere with driving. If you can't find it, just refer to the owner's manual to confirm the location. The USB functionality is simple yet reliable, handling both daily commutes and long trips with ease.
Was this review help?
13
3
Share
Expand All
More Forum Discussions

What does the SVS on the dashboard mean?

The SVS on the dashboard is a malfunction indicator light, which is a warning light that appears when the ECU or TCU of an electronically fuel-injected vehicle detects an issue with the engine or automatic transmission. All electronically fuel-injected vehicles are equipped with an SVS malfunction indicator light. For manual transmission vehicles, it indicates an engine malfunction; for automatic transmission vehicles, it indicates issues with both the engine and the automatic transmission. It is recommended to visit a repair shop for inspection as soon as possible. The SVS light is a standard indicator in the automotive industry, responsible for warning about abnormalities in the powertrain system and prompting users to have the vehicle serviced. When the powertrain system's self-diagnosis detects an abnormality, the SVS light will alert the user to have the vehicle inspected. The SVS light warning may originate from the engine, transmission, or gear shift control mechanism.
15
2
Share

What does o/d off light mean?

o/d-off warning light indicates that the overdrive of the car is in the off state. o/d is the overdrive. When the od switch is set to off, the transmission can only shift up to 3rd gear, that is, 4th gear has been restricted from shifting into. Conversely, when the gear lever is in the d position and the o/d switch is set to on, the transmission can shift up to 4th gear. The key role of o/d is to limit the gear of the transmission and prohibit the transmission from upshifting. This function can control the gear of the car within 1st, 2nd, and 3rd gears, while limiting the engine speed, making it convenient to overtake during driving. When the car needs to overtake, pressing the od button of the car will instantly drop the gear of the transmission to third gear, while the engine speed will rise, the torque will increase instantly, and the speed of the car will also be greatly improved. Using this function can reduce unnecessary switching of internal shift solenoids.
19
2
Share

How to Clean Tree Sap and Resin from a Car?

Methods for cleaning tree sap and resin from a car: You can use a car wash liquid specifically designed for removing asphalt to clean resin from the car. It has a gentle and neutral property, capable of quickly and effectively removing sticky substances like tar, asphalt, and resin from the paint surface. Additionally, if the resin on the car body is not severe, you can use hot water with a small amount of laundry detergent or dish soap, scrub the resin off with a brush, or use a cleaning agent. After treatment, wash the car and then apply wax. Alternatively, you can use volatile liquids like gasoline or alcohol (such as medicated oil) by dipping a cloth in them and wiping the affected area. After removing the resin, rinse the car body with clean water and apply wax for maintenance. Another method is using toothpaste: Sprinkle some water on the car body, wipe it briefly with a damp cloth, evenly squeeze toothpaste onto the cloth, rub it to spread, and remember the cloth should be wet. Then, you can clean a large area effectively.
8
1
Share

How to Repair Scratches on the New Qashqai Wheel Hub?

Repair methods for scratches on the new Qashqai wheel hub: 1. Inspect the scratch. If it hasn't reached the inner side of the wheel hub, it can be easily repaired. Use paint thinner to wipe around the scratch to remove dirt; 2. The deepest part of the scratch may be hard to clean, in which case a toothpick can be used to thoroughly clean it; 3. To avoid accidentally painting unrelated areas, carefully apply adhesive tape around the scratch; 4. Trim the brush tip and apply touch-up paint. After the paint dries and slightly shrinks, it's best to apply it slightly raised; 5. After painting, it takes about a week for the paint to fully dry. Once dry, use waterproof paper dipped in soapy water to smooth the surface; 6. After wiping with waterproof paper, use a compound to polish for shine, then apply wax. The new Qashqai is positioned between a compact SUV and a hatchback. In terms of body dimensions, the new Qashqai measures 4315mm in length, 1783mm in width, and 1606mm in height.
4
3
Share

Where is the cabin air filter located in the Buick New LaCrosse?

The cabin air filter in the Buick New LaCrosse is located inside the glove compartment on the passenger side. To replace the filter, you'll need to first remove the glove compartment, then open the cover of the cabin air filter housing to access it. The recommended replacement interval for the Buick New LaCrosse cabin air filter is generally every 10,000 kilometers. The steps for removing and replacing the cabin air filter in the Buick New LaCrosse are as follows: 1. Pry open the glove compartment from its side. 2. Unscrew the 3 screws at the top and 2 screws at the bottom of the glove compartment using a 7mm socket. 3. Pull out the glove compartment, which is also secured by several clips. First pull it toward the passenger seat until the clips loosen or detach, then open the glove compartment lid and firmly pull the other side outward to remove it. Since there are still electrical wires and air conditioning pipe clips attached inside the glove compartment, only loosen it at this stage without completely removing it. 4. After handling the electrical wires and air conditioning pipe clips, remove the entire glove compartment. 5. Once the glove compartment is removed, open the clips on the outer side of the cabin air filter housing, then gently pry both sides of the filter outward with a small screwdriver to remove it. Pay attention to the markings on the front of the cabin air filter - the side with text should face outward, and the arrow should point downward. Insert the new cabin air filter in the same orientation. 6. The installation steps are the reverse of the removal process.
8
0
Share

How to Replace the Antifreeze in a Sylphy?

The method for replacing the antifreeze in a Sylphy is as follows: Open the radiator cap, drain the old coolant, refill with new coolant, and install the radiator cap. In some cold regions, you can warm up the car for about 5 minutes before replacing the antifreeze, but be sure to turn off the engine and wait for it to cool down before replacement to avoid burns from hot coolant or steam. The specific steps are as follows: 1. Open the radiator cap: Remove the engine undercover, open the radiator drain plug at the bottom of the radiator, then remove the radiator cap. Before unscrewing the radiator cap, turn it slowly to release accumulated pressure, then fully unscrew it. 2. Drain the old coolant: Locate and open the coolant drain screw, usually located at the rear of the engine. For faster and more thorough drainage, you can add distilled water from the coolant filler port for cleaning, and use an air gun to blow out excess coolant. Note that the air pressure should not be too high to avoid damaging internal components. 3. Refill with new coolant: After tightening the drain screw, add new coolant from the filler port, generally not exceeding the "MAX" mark (approximately 6.6L). 4. Install the radiator cap: Warm up the engine for about 10 minutes at an idle speed of 3000 RPM. If the fan starts running, it indicates the coolant has reached normal temperature. Then, tighten the filler cap and install the radiator cap.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.