Where is the tire pressure standard for the Regal located in the car?

1 Answers
VonAbel
07/29/25 6:29pm
The tire pressure standard for the Regal can be found in the following locations: the vehicle's user manual, the label near the driver's side door (near the B-pillar), the drawer next to the driver's seat, and the fuel tank cover. According to the international GBT2978-2008 standard requirements, the recommended tire pressures are as follows: standard tires should be inflated to 2.4-2.5 bar; reinforced tires to 2.8-2.9 bar; while the maximum pressure should not exceed 3.5 bar. Tire pressure is crucial for tire longevity - both overinflation and underinflation will shorten tire lifespan. Low pressure increases tire deformation, leading to sidewall cracks and excessive flexing that generates heat and accelerates rubber aging. Overinflation causes excessive tension on tire cords, reduces elasticity, increases vehicle load during driving (potentially causing internal cracks or blowouts upon impact), accelerates tread wear, and decreases puncture resistance.
Was this review help?
17
4
Share
More Forum Discussions

How to Turn on the Air Conditioning in Geely Vision?

Geely Vision air conditioning operation method is as follows: 1. First, locate the air conditioning control area in the middle of the Geely Vision vehicle's cockpit; 2. The left knob in the Geely Vision air conditioning control area is for adjusting the temperature; 3. The middle knob in the Geely Vision air conditioning control area adjusts the air volume; 4. The right knob in the Geely Vision air conditioning control area is for adjusting the air vent direction; 5. The switch below the Geely Vision air conditioning control area selects the car's internal circulation mode and external circulation mode; 6. The "A/C" button in the Geely Vision air conditioning control area is the cooling switch button; 7. Finally, the "REAR" button in the Geely Vision air conditioning control area is used for heating the rear windshield after rain.
19
0
Share

What should I do if the Q5 sunroof makes abnormal noises?

Audi Q5 sunroof abnormal noise solutions: 1. Check the sunroof slide rail, you can add a little lubricating oil. 2. Check the fixing condition of the sunroof, it may also be caused by looseness. 3. The sunroof sealing strip is exposed to rain or sun for a long time, which is easy to age. Rubber conditioner can temporarily restore the performance of the sealing strip. Open the sunroof to the end and spray rubber conditioner on the sealing strip. 4. Another method is to adjust the sunroof screws to eliminate the abnormal noise. The following is the introduction about adjusting the sunroof screws to eliminate the abnormal noise: (1) First, open the sunroof one notch, you can find a plastic decorative strip above the track on both sides of the sunroof, which is clamped with the sunroof at the front, middle and rear points. Pull down in the direction of the front of the car and push in at the other two points to easily remove it. (2) The second step, after removing the plastic decorative strip, you can see 3 screws inside, loosen the front and rear two, do not move the middle one. (3) The third step, adjust the front part of the sunroof glass up and down slightly. Pay attention to observe the moment when the screw is loosened, whether the sunroof glass naturally tilts up or sinks, and decide whether to lift or pull down according to this trend. As for the amplitude, it does not need to be too large, about 1 mm is enough.
16
1
Share

What are the steps to add windshield washer fluid to the Volkswagen Bora?

Open the front hood of the Volkswagen Bora, locate the blue cap with a fountain pattern, lift it to find the windshield washer fluid filler port, and add the washer fluid. Below are the steps for adding windshield washer fluid: 1. Type: In northern regions, choose an antifreeze-type washer fluid to prevent the pipes from freezing and cracking before the fluid is used up in winter. In southern regions, a washer fluid with added insect-cleaning components is sufficient. 2. Dilution: Mix water and washer fluid in a 1:1 ratio. The car's windshield washer fluid capacity is approximately 1.5L, so choose a container for diluting the washer fluid between 1.25L-1.5L. 3. Addition: There is a water tank on the left side of the engine compartment with a cap marked with a fountain pattern. Lift the cap and pour in the mixed solution, ensuring it does not exceed the MAX line.
17
3
Share

What is the emission standard of Honda XRV?

Honda XRV models before 2019 comply with the China V emission standard, while models from 2019 onwards meet the China VI standard. If your region has not yet implemented the China VI standard, you can purchase a China V compliant car. If your region has already enforced the China VI standard, you need to buy a car that meets the China VI requirements. The Dongfeng Honda XRV is a compact SUV launched by Dongfeng Honda on November 18, 2014, sharing the same platform as the GAC Honda Vezel. It is equipped with a 1.8L or 1.5L engine, paired with a 6-speed manual or CVT transmission. The Dongfeng Honda XRV is the second model derived from the Honda CONCEPT-V and shares the same platform with the GAC Honda Vezel. In terms of dimensions, the XRV measures 4328*1772*1610mm in length, width, and height, with a wheelbase of 2610mm, identical to that of the GAC Honda Vezel.
10
1
Share

How to activate the lane keeping system on Audi A6?

Enter the lane keeping system option in the combination instrument, then click to activate the mode. More information about the lane keeping system is as follows: 1. The lane keeping system is a type of intelligent driving assistance system, which builds upon the lane departure warning system to provide braking control assistance. 2. Through the lane keeping system, the car uses a camera to identify the lane markings while driving, providing support for the vehicle's movement. If the car detects that it may deviate from the lane markings, it alerts the driver by vibrating the steering wheel to indicate that the car is about to leave the lane. 3. When the lane keeping system identifies the lane markings on both sides, the system is in standby mode, and the combination instrument panel displays a green indicator light, meaning the system starts operating when the car speed reaches 65 kilometers per hour.
4
4
Share

What are the body dimensions of the Mercedes-Benz GLB?

The length, width, and height of the Mercedes-Benz GLB are 4638mm, 1834mm, and 1687mm respectively, with a wheelbase of 2829mm. More details about the Mercedes-Benz GLB are as follows: 1. The Mercedes-Benz GLB is equipped with a 1.3-liter turbocharged four-cylinder engine across the entire lineup. It delivers 163 horsepower and a maximum torque of 250 Nm, with maximum power output at 5500 rpm and maximum torque output between 1620 and 4000 rpm. The engine features an aluminum cylinder head and block, and is equipped with direct fuel injection technology. 2. The Mercedes-Benz GLB's engine is paired with a 7-speed dual-clutch transmission. The dual-clutch transmission offers high transmission efficiency and fast gear shifts, making it suitable for use with small-displacement turbocharged engines. 3. The Mercedes-Benz GLB uses a MacPherson independent suspension at the front and a multi-link independent suspension at the rear, enhancing both the vehicle's handling and ride comfort.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.