Where is the tire pressure monitoring button on the Changan CS75?

2 Answers
JosephineRose
07/23/25 8:25pm
The Changan CS75 does not have a direct button for tire pressure monitoring. You need to use the square button and the inverted triangle button on the steering wheel to switch and find it. The tire pressure information of the Changan CS75 will be displayed in the center of the dashboard, which can provide early warning of abnormal tire pressure conditions, preventing accidents before they occur. Drivers do not need to get out of the car to check; they can monitor the internal condition of the tires at any time while sitting in the car, ensuring driving safety. The Changan CS75 originates from Changan's global R&D platform, incorporating international avant-garde design elements into its exterior styling, creating a brand-new urban SUV with a highly contemporary aesthetic. The overall appearance is bold and rugged, with a body that exudes strength, tension, and a harmonious yet stable demeanor.
Was this review help?
1
3
Share
BrielleLee
08/10/25 6:21pm
I've been driving the Changan CS75 for three years now, and I usually do the maintenance myself. The tire pressure monitoring button isn't actually a separate button; you need to operate it through the buttons on the right side of the steering wheel. Specifically, there are several buttons on the right side of the steering wheel, including a combination with a wheel and an OK button. You press that wheel or the menu button to switch to the vehicle information menu displayed on the dashboard, then navigate to the tire pressure monitoring settings. When driving daily, I check the tire pressure from time to time because if it's too low, it can increase fuel consumption and tire wear, and if it's too high, it may cause a blowout, especially in winter when changes are rapid. Once you get into the habit, this operation is very simple and takes just a minute. Remember, adjusting tire pressure while driving isn't very safe; it's best to do it when parked. If you find it troublesome, you can go to the shop and have the technician set it up for automatic reminders, which saves a lot of hassle.
Was this review help?
3
5
Share
Expand All
More Forum Discussions

Which gear should be used for uphill and downhill in an automatic transmission car?

For uphill driving in an automatic transmission car, use the D (Drive) gear. For downhill driving, you can use the D gear, or the L (Low) gear if your car is equipped with one. Relevant information is introduced as follows: When going downhill or on long slopes, shifting to the L gear limits the car's automatic gear shifting to the lowest gear (equivalent to first gear in a manual transmission car). This allows the car to use engine braking when going downhill, preventing the driver from having to press the brake for extended periods, which could overheat the brake pads and cause danger. When driving an automatic transmission car, remember not to shift to neutral (N) before a red light or when going downhill. Instead, keep it in the forward gear (D or L) and control the speed using the gear and brakes to avoid accidents.
7
1
Share

How to reset the tire pressure monitoring system on the Exeed LX?

Exeed LX tire pressure monitoring reset method: 1. Park the vehicle on level ground, turn off the engine, then power on; 2. Press and hold the tire pressure monitoring button; 3. After 6 seconds, you will hear an alarm sound, release the button to complete the reset. The Exeed LX is a compact SUV equipped with a 1.5L turbocharged engine, delivering a maximum horsepower of 156PS, maximum power of 115kW, and maximum torque of 230Nm. The Exeed LX has body dimensions of 4533mm in length, 1848mm in width, and 1699mm in height, with a wheelbase of 2670mm, minimum ground clearance of 145mm, and a curb weight of 1470kg.
4
1
Share

What are the standards for large parking lots?

Large parking lot standards are as follows: Large parking spaces are 15.6 meters long and 3.25 meters wide, suitable for medium and large vehicles. Relevant information is introduced as follows: The standard size design of parking spaces is mainly divided into two sizes: large and small. Large parking spaces are 15.6 meters long and 3.25 meters wide, suitable for medium and large vehicles; small parking spaces are 6 meters long and 2.5 meters wide, suitable for small vehicles. Generally, the standard size of parking spaces is determined by the size of the vehicle. Small parking spaces use dimensions of 2.5~2.75~6 meters, the width of a single-lane turning lane should not be less than 3.5 meters, and double lanes should not be less than 5 meters. The turning section should meet the needs of a vehicle making a one-time turn. For safety or to accommodate medium and large vehicles, it is often set to be more than 6 meters.
14
4
Share

How to Check if an Engine is a Three-Cylinder or Four-Cylinder?

To determine whether an engine is a three-cylinder or four-cylinder, open the engine hood and observe the number of intake and exhaust manifolds. A three-cylinder engine has three intake and exhaust manifolds, while a four-cylinder engine has four. The engine cylinder is a cylindrical metal component that guides the piston in linear reciprocating motion. Inside the engine cylinder, thermal energy is converted into mechanical energy through expansion. The cylinder allows gas to be compressed by the piston within the compressor cylinder to increase pressure, creating a cylindrical chamber in the engine where the working fluid's pressure expands, thereby driving the piston to provide power.
1
1
Share

What gear should an electric car without a P gear be parked in?

Cars without a P gear are generally manual transmission vehicles. When parking, the handbrake must be engaged. On flat ground, the car should be in neutral; when facing uphill, park in 1st gear; when facing downhill, park in reverse gear. Relevant information is introduced as follows: The commonly used P gear in electric vehicles is also called the parking gear, D gear is the drive gear, R gear is the reverse gear, and N gear is the neutral gear. The switching between different gears is achieved through conversion signals from the vehicle's controller. For example, the reverse gear is achieved by the controller reversing the motor to make the car move backward. If the R gear is engaged while the car is moving forward, there will be no response because engaging the reverse gear while the car is moving forward has no effect—the car must come to a complete stop before the reverse gear will function.
15
4
Share

Where is the 09G transmission fluid exchange interface located?

The location of the 09G transmission fluid exchange interface is as follows: The filling port (also known as the inspection port) and the draining port of the Volkswagen 6-speed automatic transmission (i.e., Volkswagen 09G/09M) are at the same position on the bottom oil pan. After removing the internal sleeve, the draining operation can be performed. Relevant information is introduced as follows: The older 09G transmission requires ATF fluid replacement every 60,000 kilometers, the DSG 7-speed 0AM transmission does not require fluid replacement, the GLI 6-speed DSG 02E transmission requires fluid replacement every 60,000 kilometers, and the 02E 6-speed DSG transmission before April 1, 2014, has a warranty of 10 years or 160,000 kilometers. Therefore, please visit the local 4S store to replace the transmission fluid every 60,000 kilometers.
1
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.