Where is the rear fog light located on a car?

1 Answers
DelDaniel
07/30/25 5:08am
The rear fog light is located on the left side or both sides of the tail lights. The main functions of fog lights are: 1. Front fog lights are used to improve illumination when the road ahead is unclear and to alert oncoming drivers; 2. Rear fog lights help vehicles behind to spot the car in low visibility conditions. Precautions for using car lights include: 1. Turn on low beams when driving at night; 2. Do not use high beams when a following vehicle is driving close to the vehicle in front in the same direction; 3. When passing sharp curves, slopes, arched bridges, crosswalks, or intersections without traffic lights at night, alternate between high and low beams to signal.
Was this review help?
1
4
Share
More Forum Discussions

How to Solve the Cylinder Pressure Difference in Cruze?

Solutions for low cylinder pressure in Cruze are as follows: 1. Fuel supply system issues: Due to blockage in the fuel tank vent hole, fuel tank switch, fuel filter, or the fuel line between the tank and the carburetor, the required fuel supply cannot be met, resulting in a lean mixture and weak engine performance. 2. Ignition system issues: Incorrect ignition timing or premature ignition causing early combustion and knocking of the combustible mixture, or due to faults in the ignition system leading to misfiring or weak sparks in the spark plugs. 3. Engine overheating: Incomplete combustion of the combustible mixture due to various reasons leads to excessive carbon deposits in the combustion chamber, resulting in poor heat dissipation and increased engine load causing overheating.
15
3
Share

How to Open the Starlight Roof on the Buick GL8?

Switch is located at the front roof reading light position. The panoramic sunroof glass and sunshade switch can only be operated when the power is in the ON state. Below is an introduction to the Buick GL8:1. Configuration: The Buick GL8 is a classic top-tier MPV under the Buick brand, equipped with a 3.0L VVT V6 engine, delivering a maximum horsepower of 178 and a top speed of 168 km/h.2. Main Advantages: (1) Spacious: Over 5 meters in length with three rows of seats. (2) Quiet: Low levels of wind noise, road noise, and engine sound during driving.
8
4
Share

How much fuel does a car consume in one hour at idle speed?

When the engine is running at idle speed, the fuel consumption is related to the engine's own displacement. Taking a 1.6L displacement engine as an example, at an idle speed of 800 rpm and without additional loads such as air conditioning or radio, if it runs for one hour, the fuel consumption is approximately 1011.2 milliliters, which means slightly more than 1 liter. The following are relevant details: 1. Vf represents the fuel consumption per hour, measured in milliliters per hour; V refers to the engine displacement, measured in liters (L); n is the engine speed per minute (rpm). According to the above formula, when a car has a displacement of 2.0L and a speed of 700 rpm, the fuel consumption at idle speed for one hour is calculated as 0.79*2.0*700=1106 milliliters. 2. If the air conditioning is turned on while idling, another formula is needed to calculate the fuel consumption: Vf=0.02636*P*V*n (ml/h), which also gives the result in milliliters of fuel consumed per hour. Compared to the previous formula, this one includes an additional parameter P, which represents the manifold pressure at idle speed. There are two ways to obtain this data: using professional instruments to measure it or utilizing the vehicle's onboard computer to read the data transmitted by sensors.
1
1
Share

How to completely turn off the start-stop function in Sagitar?

The main method to completely turn off the start-stop function in Sagitar is: it can only be manually turned off every time the engine is started. 1. There is a button next to the gear shift lever on the center console that can turn off the engine start-stop. 2. It is a circular arrow with an A letter inside and also has an OFF button in English. 3. When this button is lit, it means the engine start-stop technology is turned off. Extended content: The working principle of the start-stop system is: when the vehicle stops moving due to congestion or at an intersection. The driver presses the brake pedal and shifts to neutral. At this time, the Start/Stop system automatically detects that the engine is idling and not in gear; the wheel speed sensor of the anti-lock system shows zero; the electronic battery sensor shows that there is enough energy for the next start.
19
4
Share

How to Determine if the Sail Water Temperature Sensor is Faulty?

The simplest method is to use a multimeter for testing, then heat the water temperature sensor with a hair dryer. If the resistance value does not change, it indicates that the water temperature sensor is faulty. When the Sail's water temperature sensor fails, it can cause difficulties in starting the car, weak acceleration, water temperature gauge alarm, and other phenomena. A faulty water temperature sensor will affect the engine's power output. It is recommended to conduct timely repairs if the above symptoms occur. The function of the car's water temperature sensor is to convert the coolant temperature into an electrical signal, which is then output to the electronic control unit to adjust the fuel injection amount, modify the ignition timing, and influence the idle speed control valve, among others. When the engine coolant temperature is low, the water temperature sensor input to the ECU adjusts the air-fuel ratio to be richer, stabilizing engine operation. If the water temperature sensor fails to transmit the cold engine status information, the air-fuel ratio will become leaner, causing abnormal engine operation. Similarly, if the sensor transmits cold engine information after warm-up, the air-fuel ratio will become richer, also leading to abnormal engine operation. If the Sail's water temperature sensor is faulty, the following symptoms may occur: 1. The water temperature gauge needle does not move or points to the highest position. 2. Difficulty in cold starting because the faulty water temperature sensor still shows a hot engine temperature signal during cold starts, preventing the ECU from receiving the signal for a richer air-fuel mixture and only providing a leaner mixture to the engine. 3. Increased fuel consumption, unstable idle speed; difficulty in acceleration, with the engine speed not increasing even when the throttle is fully pressed.
20
3
Share

Does the Audi Q5 burn engine oil?

Audi Q5 burns engine oil. The following are the reasons why the Audi Q5 burns engine oil: 1. Improper selection of air filter element, oil filter element, engine oil, etc., resulting in insufficient purification of gas impurities entering the cylinder, allowing various dust particles to enter the cylinder and accelerating cylinder wear. 2. Excessive addition of engine oil. 3. Ignition timing is too early or too late. Being too early or too late can cause knocking, raising the engine temperature, and in severe cases, can lead to piston top separation and cylinder block scrapping. The following are the solutions for the Audi Q5 burning engine oil: 1. Disassemble and repair, replacing the worn parts. Although this requires a larger one-time investment, it ensures durability, reliability, and the restoration of vehicle power. 2. Use additives, but this is only a temporary solution. If you do not intend to change the car, it is not recommended to rely on additives to solve the problem.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.