···
Log in / Register

Where is the Jetta trunk drain hole located?

4 Answers
BryceAnn
07/23/25 10:22pm
Jetta trunk drain hole is located under the spare tire in the trunk, which is the lowest level of the trunk. Air conditioning drain hole: The condensate water generated during air conditioning use will be discharged outside the vehicle. The drain outlet is generally located at the bottom of the evaporator box and connected to the chassis via a hose. You may notice a puddle of water under the car after the air conditioning has been running for a while. If the drain hole is blocked, water may enter the co-pilot area through the connection, soaking items like floor mats. Engine compartment drain hole: It is basically located on both sides of the front windshield wipers. The engine compartment is a relatively open environment, so sewage and debris can flow into it along the windshield. A water barrier is designed at the rear of the engine compartment, below the edge of the windshield, with drain holes positioned at the barrier.
Was this review help?
13
5
Share
DeRonan
08/10/25 6:07pm
I've been driving a Jetta for many years, and the trunk drain hole is usually located in the corner of the spare tire well or under the plastic panel near the inner side of the rear bumper. This hole is cleverly designed mainly to prevent rainwater or car wash water from accumulating inside, which could cause rust or mold in the trunk. After washing your car, remember to check it by poking a thin wire through or pouring some water to test the drainage. If it gets clogged, the consequences can be severe, leading to water leakage in the trunk and damage to items. I recommend cleaning out debris every quarter—it's an easy task that can also extend your car's lifespan. Don't overlook this small detail; it directly affects driving safety and vehicle health.
Was this review help?
19
4
Share
Expand All
Petunia
09/23/25 6:17am
When I first bought my Jetta, I was also curious about where the trunk drain hole was located. It turns out it's in a small groove at the rear side of the trunk floor, visible around the spare tire. It's very simple to use—just lift the rubber mat to find that inconspicuous hole, which is designed to drain water and prevent accumulation. After trying to clean it myself, I felt more at ease while driving, as a clogged drain can make the trunk annoyingly damp. Here's a little tip to share with everyone: manually clear it periodically to avoid repair hassles. Fellow car enthusiasts all agree this spot is crucial—keeping it clear can prevent many potential issues.
Was this review help?
20
1
Share
Expand All
MacMaximus
11/06/25 8:33am
The location of the trunk drain hole is directly related to safety. In Jetta models, it's typically positioned along the inner edge near the taillights. This hole serves as a critical drainage point – if clogged, water accumulation can damage the vehicle body. As a driver who pays special attention to such details, I strongly recommend checking it regularly. Cleaning is simple: just lift the trunk floor mat and sweep away debris. Don't let this small issue cause major problems.
Was this review help?
16
2
Share
Expand All
More Forum Discussions

What type of engine oil is used for Buick Envision maintenance?

Buick Envision maintenance uses fully synthetic 5W30 engine oil. The detailed introduction of engine oil is as follows Engine oil grade: The grade includes two parts: classification and viscosity specification. The engine oil grade usually indicates viscosity and quality. The viscosity of lubricating oil is mostly identified by SAE grade; Functions of engine oil: The functions of engine oil include lubricating pistons and cylinders, assisting in cooling and heat dissipation, sealing to prevent leakage, and preventing excessive wear of parts. This requires the establishment of an oil film between two sliding surfaces. A sufficiently thick oil film separates the surfaces of relatively sliding parts, thereby achieving the goal of reducing wear; when the engine is working, the engine oil can bring heat back to the oil tank and then dissipate it into the air to help the water tank cool the engine. The real cooling effect comes from the water outside the engine shell; engine oil can form a sealing ring between the piston ring and the piston, reducing gas leakage and preventing external pollutants from entering; Precautions: When adding engine oil, the amount should be slightly lower than the standard scale. Excessive engine oil will increase the rotational resistance of the crankshaft, reduce the output power of the engine, and excess oil may enter the combustion chamber and participate in combustion, causing the vehicle to burn oil, emit blue smoke, and even increase fuel consumption.
1
5
Share

How to Check the Car Oil Dipstick?

To check the car oil dipstick, follow these steps: 1. The oil tank is generally located near the engine. Locate the oil dipstick on top of the oil tank. 2. The car must be parked on level ground with the engine off when pulling out the oil dipstick for measurement. 3. Pull out the dipstick. There is a textured area at the end with upper and lower lines. First, wipe the dipstick clean, then reinsert it and pull it out again. The oil level is acceptable as long as it falls between the upper and lower lines. If the oil level is above the upper line, it indicates too much oil; if it's below the lower line, it means there's insufficient oil.
14
4
Share

What is the code name for China V?

China V refers to the National Fifth Stage Emission Standard for Motor Vehicle Pollutants, which was issued on September 17, 2013, and officially implemented nationwide in 2017. As of 2019, China was still implementing the China V emission standard, but some cities began implementing the China VIa emission standard on July 1, 2020. Below is an introduction to automobile emission standards: Automobile emission standards regulate the content of harmful gases emitted from vehicle exhaust, such as CO (carbon monoxide), HC+NOx (hydrocarbons and nitrogen oxides), and PM (particulate matter, soot). These standards were first introduced in China in 2004. The implementation of automobile emission standards helps promote environmental protection and reduce pollution.
2
3
Share

How much engine oil does the Envision need?

Envision needs about 5 liters of engine oil. Precautions for adding engine oil: 1. When adding engine oil, just add it between the min and max marks. 2. After adding the engine oil, start the vehicle and check it 3 minutes after turning it off. Because the oil filter needs to be replaced when changing the engine oil, and the newly replaced oil filter does not contain oil. After starting the vehicle, the oil will flow into the oil filter. Turning off the engine for 3 minutes allows the oil to flow into the oil pan, making the oil level check more accurate. 3. Adding too much oil will affect the normal operation of the crankshaft and also increase the vehicle's fuel consumption, so the oil must be added within the specified range.
18
4
Share

How to Reset the Smart Maintenance Light?

Smart cars are wholly owned by Mercedes-Benz, established in 1994, and are a luxury brand among microcars. The vehicles are equipped with two types of engines: the first is a 0.9-liter turbocharged engine, and the second is a 1.0-liter naturally aspirated engine, along with a very distinctive soft-top convertible. The method to reset the Smart maintenance light is as follows: 1. Turn on the vehicle's power; 2. Use the left multifunction button to locate the vehicle's maintenance information; 3. Open the vehicle's mileage data and hold the OK button for 20 seconds; 4. After the dashboard maintenance information starts flashing, press and hold the RES button; 5. The vehicle's maintenance light will be reset.
19
4
Share

How to Replace the Battery in a Levin Car Key?

Levin is a 'New Sensory Leading Compact Sedan' based on Toyota's MC platform, specially and deeply customized for Chinese consumers. The following are the specific steps to replace the battery in a Levin car key: 1. First, remove the mechanical key. Use a screwdriver to gently pry at the spot where the mechanical key is taken out, then open the back cover. Avoid getting the circuit board wet and try not to touch it, as moisture or contact may damage the circuit board. 2. Next, replace it with a new button battery of the same model, ensuring the '+' positive side is facing upwards during installation to complete the process.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.