Where is the fuel tank switch of the Excelle?

How to distinguish between Lingyu and Passat?

It can be said that the new Passat is the upgraded version of the Passat Lingyu. The production platforms of these two models are different. The new Passat is built on the PQ46 platform, equipped with a new TSI turbocharged direct injection engine paired with a DSG dual-clutch transmission, while the Passat Lingyu is based on the older Volkswagen PL45 platform. The differences between the Passat and Lingyu are as follows: 1. Different models: The Passat (PASSAT) is a mid-sized sedan designed by Volkswagen AG in Germany. It is classified as a B-segment car in Volkswagen's lineup. The overall dimensions of the Passat Lingyu are slightly increased in length and width compared to the B5, and the interior features an added fuel tank cap on the left front door (the B5 design placed it next to the handbrake) and a remote trunk button. 2. Different vehicle configurations: The new Passat is built on the PQ46 platform, equipped with a new TSI turbocharged direct injection engine paired with a DSG dual-clutch transmission. The Passat Lingyu is based on the older Volkswagen PL45 platform.

13

0

Share

Is it necessary to replace the three filters when changing the engine oil?

It is necessary to replace the three filters when changing the engine oil. The core material of the oil filter is filter paper, which is particularly difficult to clean. Many fine impurities filtered out get trapped inside the filter paper, and even if the exterior is cleaned, the internal impurities remain difficult to remove. Continued use of a dirty filter can lead to reduced lubrication oil pressure, directly causing increased engine wear. Below is an introduction to related car maintenance procedures: 1. Exterior inspection: Before driving, check the doors, engine hood, trunk, and glass condition. Inspect the car body for damage, tilting, oil leaks, or water leaks. 2. Engine and various fluids: Check the fastening condition of engine components and inspect all engine joints for oil or coolant leaks. Adjust and tighten belts as needed, and check the fastening of all hoses and wiring. Top up engine oil, coolant, and battery electrolyte. 3. Tires: Inspect tire wear and clean the trunk. Replace tires when they approach the wear indicators. Check for bulges, abnormal wear, aging cracks, or other damage on tires. 4. Cleaning and lubrication: Clean oil stains from the engine compartment hood, door hinges, and trunk hinge mechanisms, then lubricate them. Generally, antifreeze should be replaced every 2 years during maintenance, and the cooling system should be thoroughly flushed. Due to the hygroscopic nature of the braking system, brake fluid should be replaced every two years.

15

2

Share

What to Do If the Parking Ticket Is Not Displayed on Traffic Management 12123?

If the parking ticket is not displayed on Traffic Management 12123, you can wait patiently, as it can take up to 14 days to appear. Generally, after receiving a parking violation ticket, the information is entered into the traffic management system for review. If the review is approved, the information will be uploaded within 24 hours, meaning it will appear on the 12123 website. At the latest, it should be published within 14 days. If the parking violation information does not appear on the 12123 website after 14 days, it means the information was not approved, and there is no violation. Additional Information: How to Handle a Parking Violation Notice Not Found on 12123: 1. Traffic Management 12123 is a platform where car owners can handle various traffic-related matters. If you receive a parking violation notice, you can process it online. 2. If you log in to Traffic Management 12123 but cannot find the relevant record, it may be because the violation has not yet been displayed in the system. You can wait a few days and check again. 3. Another possibility is that the parking violation notice does not have the official seal of the traffic police or the fine amount. In this case, the notice is mainly a warning reminder from the traffic police and does not impose a penalty on the car owner.

9

2

Share

What is the standard range for piston ring three gaps?

Introduction to the standard range of piston ring three gaps: end gap 0.25-0.5mm, side gap 0.03-0.06mm, back gap 1mm; size requirements vary for different engines. The three gaps of piston rings refer to the opening (ring gap) clearance, axial clearance (side gap), and radial clearance (back gap). Below is an introduction to the three gaps of piston rings: 1. Measurement of end gap: The end gap is the clearance at the opening when the piston ring is installed in the cylinder, to prevent the piston ring from seizing due to thermal expansion. When checking the piston ring end gap, place the piston ring flat in the cylinder, push it flat with the piston top, and then measure the opening clearance with a feeler gauge, generally 0.25-0.50mm. The first ring has a larger end gap than the others due to higher working temperatures. 2. Measurement of side gap: The side gap refers to the up and down clearance of the piston ring in the ring groove. A too large side gap affects the sealing function of the piston, while a too small side gap can cause the piston ring to seize in the groove. When measuring, place the piston ring in the ring groove and measure with a feeler gauge. The first ring, due to higher working temperatures, generally has a value of 0.04-0.10mm, other gas rings generally 0.03-0.07mm, ordinary oil rings have a smaller side gap, generally 0.025-0.07mm, and composite oil rings have no side gap. 3. Measurement of back gap: The back gap refers to the clearance between the back of the piston ring and the bottom of the piston ring groove after the piston is installed in the cylinder, generally represented by the difference between groove depth and ring thickness, usually 0.30-0.40mm. Ordinary oil rings have a larger back gap; a common practice is to install the piston ring in the groove, and if it is below the ring land and can rotate freely without sticking, it is considered suitable.

11

5

Share

What does 300cc mean?

300cc equals to 0.3l displacement, where "300CC" refers to the exhaust volume of a motorcycle engine's combustion chamber. CC is the volumetric unit for cylinder displacement, with 1CC equivalent to 1ml. According to China's relevant standards, different displacements correspond to the following vehicle types: 30CC and below are defined as fuel-assisted bicycles. 30-50CC are defined as mopeds. Above 50CC are defined as regular motorcycles; among regular motorcycles, they can be further categorized as: entry-level motorcycles defined as 250-400CC. Mid-level motorcycles are defined as 500-750CC. Heavy-duty motorcycles (liter-class) are defined as above 1000CC. Motorcycle licenses are divided into D, E, and F categories. Motorcycles come in two types: two-wheeled and three-wheeled. In addition to directly applying for initial two-wheeled motorcycle or initial three-wheeled motorcycle licenses, one can also apply for an upgrade to a two-wheeled or three-wheeled motorcycle license. Applicants can apply for a motorcycle driver's license with their resident ID card at any location nationwide, take the exam, and upon passing, receive the motorcycle driver's license. For the daily maintenance of a motorcycle's engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil based on mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, causing various problems for the engine. To avoid malfunctions, change the oil regularly based on usage conditions and keep the oil level moderate. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, it may burst the filter element or open the safety valve, bypassing through the bypass valve and bringing contaminants back to the lubrication area, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. In small amounts, it suspends in the oil; in large amounts, it precipitates from the oil, clogging filters and oil holes, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.

17

3

Share

What size is 700*23c?

700*23c is 24 inches. The functions of tires are as follows: 1. Load-bearing: Supporting the entire weight of the vehicle and bearing the load of the car. 2. Torque: Transmitting traction and braking torque, ensuring good adhesion between the wheels and the road surface to improve the car's power, braking, and passability. 3. Protection: Preventing severe vibrations and early damage to automotive components, adapting to the vehicle's high-speed performance while reducing driving noise, ensuring driving safety, handling stability, comfort, and energy efficiency. Tires are circular elastic rubber products mounted on metal rims, designed for ground rolling on various vehicles or machinery, featuring high wear resistance.

19

3

Share

Where is the fuel tank switch of the Excelle?

How to distinguish between Lingyu and Passat?

Is it necessary to replace the three filters when changing the engine oil?

What to Do If the Parking Ticket Is Not Displayed on Traffic Management 12123?

What is the standard range for piston ring three gaps?

What does 300cc mean?

What size is 700*23c?

How wide is approximately 30cm when viewed in the rearview mirror?

What lights to turn on when entering a highway entrance?

What is the Difference Between Adding a License and Directly Taking the Test?

Is the Inspection Validity Period the Same as the Vehicle Inspection Time?