···
Log in / Register

Where is the brake light fuse of Geely Emgrand GS located?

4 Answers
NorahFitz
07/29/25 9:20am

Geely Emgrand GS brake light fuse is located inside the dashboard on the driver's side. Function of the fuse: The fuse protects the car's electrical equipment by preventing overload in the circuit. A blown fuse indicates a fault in the circuit it protects and has stopped working. If you suspect a fuse is faulty, you can remove it from the fuse box for inspection to see if the metal wire inside the fuse has melted. Two different types of fuses: Blade fuse - thinner, plug-in type, allows a current of 5-30A in the circuit; Slow-blow fuse - square, plug-in type, allows a current of 30-60A in the circuit.

Was this review help?
9
0
Share
LaKaden
08/12/25 9:31am

As a long-time car enthusiast, I remember that the brake light fuse for the Geely Emgrand GS is usually located in the engine compartment fuse box. You need to open the hood and look for a black box near the battery or windshield side. After opening the cover, check the labels—the brake light might be marked as F2 or a similar position. A blown fuse is often caused by a short circuit or overload in the brake lights, which is particularly dangerous because the rear vehicle won't see your deceleration, increasing the risk of an accident. Checking it yourself is quite simple: use a multimeter or visually inspect whether the fuse is melted. When replacing it, always use a fuse with the same amperage to avoid damaging the circuit. During routine car maintenance, take a moment to inspect the fuse box to prevent issues, especially in older cars where wiring aging is a concern. The location might vary depending on the car model, so keeping the owner's manual handy or consulting a professional repair shop is the safest approach—after all, road safety should never be taken lightly.

Was this review help?
15
5
Share
Expand All
LaKevin
10/06/25 5:12am

As a safety-conscious driver, I discovered that the brake light fuse for the Geely Emgrand GS is mostly located in the small fuse box under the driver's seat. Lift the panel near the accelerator, and you'll find a bunch of fuses—look for labels like "Brake Light" corresponding to F1, etc. If the fuse blows, the brake lights go out, which is a big deal. At night or in rain or fog, drivers behind might not see you and could rear-end your car. I've replaced it myself: gently pull the fuse with pliers to test, and if it's broken, replace it. A reminder to everyone: don't rely solely on lights while driving. Regularly check your lights to prevent small issues from becoming big ones. Even if your car isn't driven often, check the battery voltage to ensure stability. If unsure of the location, take a photo of the manual for reference. Always disconnect power before working—small steps can save lives.

Was this review help?
1
1
Share
Expand All
LeArthur
11/19/25 6:38am

I've repaired my friend's Emgrand GS before. The brake light fuse is usually located in the fuse box on the front right side of the engine compartment. After starting the car, first test the light. If it doesn't work, open the cover to find the main fuse box, check the internal diagram to locate the F-position fuse. Fuse blowouts commonly occur during sudden braking due to current surges or bulb issues. Don't rush to pull out tools when handling it - confirm the circuit is broken before replacing the fuse. Take the opportunity to maintain the lighting system by cleaning dust to prevent short circuits. Driving safety relies on these details.

Was this review help?
17
3
Share
Expand All
More Forum Discussions

What is the real reputation of Geely Borui after three years?

Geely Borui has relatively high fuel consumption, powerful engine performance, strong acceleration, beautiful appearance, good interior craftsmanship, high cost-performance ratio, and rich configurations. Geely Borui exterior design: The Borui GE has undergone optimized designs on multiple parts such as the grille and front/rear bumpers, making the overall shape more dynamic and stylish. The optimized water ripple grille is more square and more imposing. The lower grille design has been updated from the original ribbon style to a blade style, with the addition of a horizontal chrome trim, giving the front face more layers and a three-dimensional feel. Geely Borui interior design: The Borui GE adopts a "Starship Cockpit" design, with the interior largely wrapped in soft plastic materials. The center console is outlined with "V" shaped lines and innovatively integrates the instrument panel, central control screen, and co-pilot console into one, presenting an IMAX-like visual effect. Additionally, the dual 12.3-inch central control LCD screen and full LCD instrument panel, the sci-fi atmosphere lighting of the "Time Tunnel," intelligent voice control, piano key-style air conditioning control buttons, the floating feeling of the horizontally designed gear lever, and the driving mode knob crafted with micron-level precision all showcase Geely Borui's pursuit of premium luxury quality and spiritual experience.
16
2
Share

How to Cancel the Tire Pressure Warning Light on Volkswagen?

Method to reset the tire pressure warning on Volkswagen Sagitar: First, turn on the ignition switch, then press and hold the tire pressure monitoring reset button. After hearing a "beep" sound, release the button. The tire pressure monitoring system will store the current normal tire pressure data, automatically clear the previous data, and finally, the warning light on the dashboard will turn off, completing the tire pressure reset. There are three commonly used methods for tire pressure monitoring: Direct Tire Pressure Monitoring: Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire pressure. The pressure information is transmitted wirelessly from inside the tire to a central receiver module, which then displays the tire pressure data for each tire. Indirect Tire Pressure Monitoring: When the pressure in a tire decreases, the vehicle's weight causes the rolling radius of that tire to become smaller, resulting in a faster rotation speed compared to the other wheels. By comparing the differences in rotation speeds between the tires, the system monitors the tire pressure. Introduction to Tire Pressure Monitoring System (TPMS): It combines the advantages of both systems mentioned above. Direct sensors are installed in two diagonally opposite tires, and a four-wheel indirect system is also equipped.
3
1
Share

What are the dimensions of the A7L?

Audi A7L dimensions are 4976mm in length, 1908mm in width, and 1405mm in height, with a wheelbase of 2928mm. A7L interior features: Two high-definition touchscreens measuring 10.1 inches and 8.6 inches enable numerous entertainment and convenience operations, providing feedback through tactile and auditory sensations to create a more convenient and avant-garde digital cockpit. A 12.3-inch high-resolution TFT screen is positioned directly in the driver's line of sight, displaying multiple driving information in a simple, easy-to-understand, and clear layout. A7L powertrain specifications: The A7L is equipped with a 3.0TFSI V6 engine, delivering a maximum output of 250kW and a robust torque of 500Nm, achieving 0-100km/h acceleration in approximately 5.6 seconds while ensuring high fuel efficiency and low emissions. It features the latest generation quattro intelligent all-wheel-drive system, which adaptively distributes torque between the front and rear axles according to different scenarios, enabling predictive and rapid response for all-wheel-drive mode switching. The active air suspension also adapts to various road conditions. Additionally, the 48V mild hybrid system provides comprehensive electrification support, offering energy recovery during braking for use in acceleration, resulting in more powerful performance, enhanced ride comfort, and a more elegant and composed driving experience.
17
2
Share

How to Remove the Wiper Blades on an Audi A4?

Audi A4 wiper blade removal method is as follows: 1. First, lift the metal wiper arm of the FAW-Volkswagen Audi A4 vehicle off the windshield, then stand the wiper upright, ensuring it remains stable. 2. Locate the plastic tab securing the rubber wiper blade to the metal arm. Press the tab to release and remove the old wiper blade from the Audi vehicle. 3. Additional Information: The wiper blade is a device used to sweep away rain and dust attached to the vehicle's windshield, improving driver visibility and enhancing driving safety.
16
1
Share

When will the China 6 emission standard be implemented in Hunan?

Hunan will implement the China 6 emission standard from July 1, 2019, in accordance with the national unified deployment. The country divides the "China 6 emission standard" into two phases: "China 6A" and "China 6B". China 6A is a transitional phase from China 5 to China 6, with lower emission requirements for carbon monoxide, non-methane hydrocarbons, nitrogen oxides, and PM particulate matter compared to China 6B. Below are the official implementation dates for the two China 6 standards: 1. The official implementation date for China 6A standard is July 1, 2020. 2. The official implementation date for China 6B standard is July 1, 2023.
18
0
Share

What causes the roof noise in Roewe RX5?

The main reasons for the roof noise in Roewe RX5 are as follows: 1. Loose fixing clips on the car roof, which require inspection and re-fixation: The interior panels of the car are mostly fixed to the body with clips. When the clips become loose, the interior panels will make noise. To solve the noise issue, it is necessary to accurately locate the source of the noise and then reinforce or replace the clips in the affected area. 2. Poorly secured wiring inside the car roof, causing noise: The roof needs to be dismantled for repair. Additionally, the Roewe RX5 adopts the brand's signature Rhythm design language, featuring a large front grille and decorative chrome trim.
13
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.