Where is the auto start-stop switch for the GL8?

2 Answers
LaSara
08/30/25 4:36am
The auto start-stop switch for the GL8 is located on the lower right side of the center console gear lever, featuring a touch-sensitive button. To turn it off, simply touch the button. Taking the 2020 GL8 as an example, its body dimensions are: length 5219mm, width 1878mm, height 1805mm, with a wheelbase of 3088mm and a fuel tank capacity of 71 liters. The 2020 GL8 is equipped with a MacPherson independent front suspension and a multi-link independent rear suspension. It is powered by a 2.0L turbocharged engine, delivering a maximum horsepower of 237 PS, a maximum power of 174 kW, and a maximum torque of 350 Nm, paired with a 9-speed automatic transmission.
Was this review help?
1
2
Share
GabrielleMarie
09/11/25 8:33am
I remember when looking for the auto start-stop switch on the Buick GL8, it's usually located in the center console area near the gear shift, specifically in the button panel on the right side of the steering wheel. The button is marked with a small 'A' icon or the words 'AUTO STOP/START', and pressing it turns the function on or off. As someone who drives this car often, I have to say the placement is quite thoughtful—close to hand, making it easy to operate while driving. Some people might miss it because the button is nestled among the air conditioning or lighting controls on the panel. When using it for the first time, it's best to start the car and observe the dashboard indicator light to locate it. Additionally, the auto start-stop is enabled by default, which can be annoying in city traffic with frequent stops and starts. I often turn it off to reduce battery drain, though keeping it off for long periods might increase fuel consumption. In short, it's best to check the owner's manual diagrams to confirm and avoid distracted fumbling.
Was this review help?
9
3
Share
Expand All
More Forum Discussions

What is the function of the blow-off valve in a turbocharged engine?

The function of the blow-off valve is to prevent the turbo pressure from becoming too high, and it also helps avoid excessive pressure in the intake manifold. If the turbo pressure is too high, it can lead to turbocharger failure. Similarly, if the pressure in the intake manifold is too high, it can compromise sealing performance. Here are the relevant details: 1. Turbocharged engines in cars typically have two blow-off valves—one in the intake system and another on the turbocharger itself. The intake system's blow-off valve activates when the driver releases the throttle pedal. When the throttle pedal is released, the throttle valve remains at a very low opening. However, the turbocharger continues to compress air and deliver it to the intake manifold. At this point, the engine does not require as much air, and the throttle valve opening has already decreased. This leads to a large volume of air accumulating in the intake manifold, increasing the pressure inside. If the pressure in the intake manifold becomes too high, it can cause the intake manifold to rupture. Therefore, the blow-off valve is necessary—after releasing the throttle pedal, it can vent some of the air from the intake manifold, preventing excessive pressure buildup. 2. When the engine speed is too high, the turbocharger's speed also increases, and the turbo pressure rises. If the turbo pressure becomes too high, it can cause the turbocharger to fail. At very high engine speeds, the turbo's blow-off valve opens, allowing exhaust gases to bypass the turbocharger and enter the exhaust manifold directly. This prevents the turbo pressure from continuing to rise.
8
1
Share

What brand of transmission is used in the Great Wall Haval M6?

Great Wall Haval M6 transmission is produced by Getrag. Getrag (Jiangxi) Transmission System Co., Ltd. is a joint venture between Germany's Getrag Group and Jiangling Motors Group, established as a provider of transmission technology products and services. It officially commenced operations in January 2007 in Nanchang, Jiangxi. The Great Wall Haval M6 transmission uses either a 6-speed manual transmission or a 7-speed wet dual-clutch transmission. A manual transmission is a gear-shifting device used to alter the speed and torque transmitted from the engine to the drive wheels, enabling the vehicle to achieve different traction and speed under various conditions such as starting from a standstill, climbing hills, turning corners, and accelerating. For the Great Wall Haval M6 transmission, the following points should be noted during daily use: Do not delay changing the transmission oil for extended periods. Prolonged failure to change the transmission oil can lead to damage to internal components such as bearings and the housing. Avoid coasting in neutral for long durations. While driving manual transmission vehicles, many experienced drivers tend to coast in neutral, but for automatic transmission vehicles, this can cause the transmission to overheat and may result in a noticeable jolt when shifting back into D (Drive) mode. Never shift into D/R (Drive/Reverse) before the vehicle has come to a complete stop. Many drivers, in an attempt to showcase smooth operation, shift directly into reverse while the vehicle is still moving, which can cause significant damage to the transmission gears and, over time, lead to gear grinding and other failures. Avoid frequently climbing steep slopes in D mode. When facing steep inclines, automatic transmission vehicles often overheat due to high load or may upshift prematurely, resulting in insufficient climbing power. In such cases, it is advisable to use manual mode to limit the gear to a lower speed or switch to sport mode to protect the transmission. Do not tow the vehicle over long distances. In the event of a breakdown, an automatic transmission vehicle should be transported using a flatbed tow truck, with the vehicle in N (Neutral) mode when being moved onto the tow truck. Using a tow rope or directly towing the vehicle is not recommended.
13
3
Share

What is the 0-100 km/h acceleration time of the Honda Civic?

According to official data, the Honda Civic is available in two engine displacements: 1.5T and 1.0T. The 1.5T model accelerates from 0-100 km/h in 8.5-9.6 seconds, while the 1.0T model takes 11.2-11.3 seconds. Factors affecting a vehicle's 0-100 km/h acceleration time include: Torque: Torque essentially represents the strength of the engine. Higher torque means greater force to propel the vehicle, resulting in faster acceleration. The Honda Civic HATCHBACK 1.5T has a maximum torque of 220 Nm and accelerates from 0-100 km/h in 9.3 seconds. In comparison, the Nissan Sylphy has a torque of 155 Nm and takes 12.2 seconds for the same acceleration. Transmission efficiency: The transmission acts as a medium for power delivery, inevitably involving power loss. Higher transmission efficiency leads to better acceleration performance. Generally, transmission efficiency ranks as follows: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. The Honda Civic is equipped with a CVT transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is called the power-to-weight ratio (measured in Hp/T). A higher power-to-weight ratio results in faster acceleration. The Honda Civic HATCHBACK 1.5T has a power-to-weight ratio of 131.79 Hp/T and accelerates from 0-100 km/h in 9.3 seconds. The Nissan Sylphy has a power-to-weight ratio of 102.69 Hp/T and takes 12.2 seconds for the same acceleration.
7
2
Share

What is the appropriate tire pressure for Camry?

The recommended tire pressure range for Camry is between 2.4bar and 2.5bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2bar in winter and decreased by 0.1bar in summer. This data is based on the international GBT2978-2008 standard. Camry's tire pressure monitoring can be viewed on the dashboard. Operate through the multifunction buttons on the steering wheel. The specific operation method is: the left menu button has a vehicle icon (below the music icon), pressing this icon will display the tire pressure. Generally, a tire pressure exceeding 2.8bar is considered too high, and a tire pressure below 2.0bar is considered too low. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; causing steering wheel vibration and deviation, reducing driving comfort; accelerating wear on the central tread pattern of the tire, shortening tire life; increased body vibration, indirectly affecting the lifespan of other components; excessive stretching deformation of tire cords, reducing tire elasticity, increasing the load on the car during driving. Hazards of insufficient tire pressure: Increased friction coefficient with the road surface, leading to higher fuel consumption; causing heavy steering and deviation, affecting driving safety; increased movement of various parts of the tire, leading to abnormal heating due to excessive rolling; reduced functionality of cords and rubber, causing delamination or cord breakage, excessive friction with the rim, damaging the tire bead area, and abnormal wear; multiplied friction between the tire and the ground, rapid rise in tire temperature, softening of the tire, and sharp decline in strength. High-speed driving may lead to tire blowout. If the tire pressure monitoring indicator light comes on (a yellow icon, an irregular circle without a seal, with four small spikes below and an exclamation mark inside), there are generally three reasons: Abnormal tire pressure: Usually, an alarm is triggered when the pressure is below 1.8bar or above 3.0bar. At this time, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tire, the tire pressure was not reset in time, causing the tire pressure monitoring system to still record the original data, and the tire pressure monitoring indicator light will remain on. At this time, simply perform a tire pressure reset. Damaged tire pressure sensor: The tire pressure sensor is used to monitor tire pressure and is directly installed inside the tire, connected to the tire inflation port. If the sensor is damaged during driving, it will also cause the tire pressure fault light to come on. For sensor damage, only a new replacement can be installed.
20
3
Share

Where is the ETC mounted?

The installation position of a car ETC is generally in the upper middle part of the front windshield, while for large vehicles such as trucks and buses, it is installed in the lower middle part. The appropriate installation position should be no lower than 1.2 meters and no higher than 2.5 meters, with an installation angle between 30 and 90 degrees. For vehicles with anti-explosion film or those that have it installed later, it may affect the signal transmission of the microwave communication link, so it should be installed in the microwave skylight strip. ETC is the abbreviation for Electronic-Toll-Collection, meaning electronic toll collection system. To apply, you need to provide the original and photocopies of the vehicle owner's valid ID card and vehicle registration certificate. If it's not the owner applying, the agent's valid ID card is also required. The photocopy of the vehicle registration certificate should include the page with the most recent annual inspection stamp. Additionally, a bank card for deducting highway tolls is needed, and the vehicle must be registered under the name of an individual aged between 18 and 60. Here are some precautions for installing ETC: Do not obstruct the view; it's best to install it behind the rearview mirror: Many car models have a large tilt angle of the windshield, which can reduce the driver's field of vision. If this is not considered during ETC installation, it can increase the driver's blind spots. Installing it behind the right side of the rearview mirror can help avoid obstructing the view. Do not interfere with charging: The ETC electronic tag consumes power, but generally, it does not need to be charged or have its battery replaced because it has a solar panel on the back that can charge itself. Therefore, during installation, avoid the black areas on the windshield and positions that might block the solar panel. Once installed, do not remove it arbitrarily: The button in the middle of the adhesive is an anti-removal guide rod, connected to a switch below. After the electronic tag is installed, the windshield will press the anti-removal guide rod in. If it is removed arbitrarily, the guide rod will pop out and trigger the switch, locking the electronic tag and rendering it unusable. You would then need to go to an ETC service point to unlock it. This is designed to prevent multiple vehicles from sharing one device. When using ETC, note the following: The ETC transaction sensing area is 8 meters. To prevent the ETC device of the vehicle in front from malfunctioning, maintain a distance of more than 10 meters from the vehicle in front to avoid automatic sensing and paying for the front vehicle. The ETC lane recognition speed is 20 kilometers per hour; driving too fast may prevent the vehicle device information from being read, leading to a failed transaction. When using a debit card linked to ETC, insufficient balance can also cause the transaction to fail.
4
1
Share

How many cylinders does the BMW 325 engine have?

The BMW 325 engine is a 4-cylinder engine. An engine is a machine that can convert other forms of energy into another type of energy, usually converting chemical energy into mechanical energy. Taking the 2021 BMW 325 as an example, its body dimensions are: length 4719mm, width 1827mm, height 1459mm, wheelbase 2851mm, and fuel tank capacity 59l. The 2021 BMW 325 is equipped with a 2.0T turbocharged engine, with a maximum power of 135kW and a maximum torque of 300Nm, paired with an 8-speed automatic manual transmission.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.