Where is the air conditioning filter located in the Haima M6?

1 Answers
DiPaisley
07/29/25 12:13pm
Haima M6 air conditioning filter is located inside the glove compartment on the passenger side. You can see it after removing the glove compartment. Generally, the air conditioning filter should be replaced every 10,000 kilometers. If the air conditioning filter is not replaced for a long time, it will affect the performance of the air conditioning system and the health of the passengers. Here are the steps to replace the air conditioning filter: 1. Locate the position of the filter on the passenger side inside the car. 2. Gently remove the glove compartment. 3. Take out the old air conditioning filter and replace it with a new one. 4. Reinstall the glove compartment back into place.
Was this review help?
12
2
Share
More Forum Discussions

How Often Should the Brake Pads on a Lavida Be Replaced?

There is no fixed replacement interval for Lavida brake pads; it depends on driving conditions and habits, as these factors affect brake pad wear. The best approach is to check the wear level during routine maintenance and replace them immediately if they reach the critical point. The Lavida is a compact sedan under the Volkswagen brand, with dimensions of 4670 mm in length, 1806 mm in width, and 1474 mm in height, and a wheelbase of 2688 mm. The Lavida is equipped with three engine options: a 1.2-liter turbocharged engine, a 1.4-liter turbocharged engine, and a 1.5-liter naturally aspirated engine.
20
5
Share

What is the reason for the bulb fault light in a Volkswagen car being on when all bulbs are lit?

The reasons for the bulb fault light in a Volkswagen car being on when all bulbs are lit are: 1. The bulb power does not match the battery power; 2. Fault in the computer's encoding and decoding function. Taking the 2017 Volkswagen Tiguan as an example, it is a compact SUV with body dimensions of: length 4506mm, width 1809mm, height 1685mm, wheelbase 2684mm, and a body weight of 1600kg. The 2017 Volkswagen Tiguan is equipped with a 1.8T inline 4-cylinder turbocharged engine, with a maximum horsepower of 160PS, maximum torque of 250Nm, maximum power of 118kW, and is paired with a 6-speed automatic manual transmission.
15
4
Share

Where is the ignition coil of the Sylphy located?

The ignition coil of the Sylphy is located on the engine cylinder head. The method for replacing the ignition coil is as follows: 1. Open the ignition coil cover on top of the engine and use a pentagonal wrench to remove the ignition coil fixing screws; 2. Disconnect the ignition coil power plug, gently pry it up with a screwdriver, and remove the ignition coil; 3. Install the new ignition coil, tighten the screws, and reconnect the power plug. Taking the 2021 Sylphy as an example, it is a compact car with body dimensions of: length 4631mm, width 1760mm, height 1503mm, wheelbase 2700mm, minimum ground clearance 166mm, and body weight 1188kg.
13
3
Share

What are the causes of abnormal engine idle noise?

Engine idle noise may be caused by excessive clearance between parts, engine misfire, or engine knocking. Abnormal noise caused by excessive clearance between parts: Clearance between parts is an important factor affecting automobile assembly quality. When lubrication, temperature, load, and speed are constant, the abnormal noise becomes more obvious as the clearance increases. Some engine components produce noise due to increased clearance caused by wear. Engine misfire noise: Engine misfire mainly refers to one or more cylinders not working properly, manifested as obvious intermittent exhaust gas flow from the vehicle, severe shaking of the exhaust pipe, and clearly audible "popping" or thumping sounds from the engine.
3
2
Share

What are the precautions for switching from 95-octane gasoline to 92-octane gasoline?

The precautions for switching from 95-octane gasoline to 92-octane gasoline are: 1. Confirm whether the current vehicle can use 92-octane gasoline, which is indicated on the fuel tank cap. If the vehicle supports the use of 92-octane gasoline, you can directly replace 95-octane gasoline in the fuel tank; 2. 95-octane gasoline and 92-octane gasoline should not be mixed in the fuel tank for a long time, as long-term mixing will affect the ignition system, fuel injection system, and engine lifespan; 3. Do not frequently change gasoline, as frequent changes will affect the normal working state of the engine; 4. Refueling should be done at a regular gas station, and the gasoline used should meet the fuel standards specified by the vehicle.
5
0
Share

What are the symptoms of a faulty camshaft sensor?

The symptoms of a faulty camshaft sensor are: 1. Difficulty in ignition, making the engine hard to start; 2. Difficulty in accelerating when the car is hot or the engine may stall directly; 3. Increased fuel consumption, lack of power, inability to accelerate properly, and continuous shaking while driving. The function of the camshaft position sensor is to collect the position signal of the valve camshaft and input it into the ECU, enabling the ECU to identify the top dead center of cylinder compression for sequential fuel injection control, ignition timing control, and knock control. The camshaft sensor position signal is also used to identify the first ignition timing when the engine starts, determining which cylinder piston is about to reach the top dead center, hence it is also known as the cylinder identification sensor.
15
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.