Where is Dayang Motorcycle Produced?

What is the wading depth of the Audi A4?

The maximum wading depth of the Audi A4 is 320mm. The wading depth of the Audi A4 is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when driving through waterlogged roads. Therefore, in terms of safe wading depth, off-road vehicles and SUVs have obvious advantages. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake of the Audi A4 is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. Alternatively, installing a snorkel can increase the height of the engine's air intake, thereby improving the maximum wading depth. If wading is unavoidable, the following safe and correct operations should be performed: Before driving through water, always turn off the auto start-stop function to prevent the engine from automatically restarting if the vehicle stalls in the water, which could cause severe damage due to water entering the engine. Assess the underwater road conditions based on the passage of vehicles ahead and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, use warning water level markers, trees, or the wheels and doors of other vehicles as reference points to estimate water depth before deciding whether to proceed. Be aware of your vehicle's safe wading depth. If the water depth exceeds half the tire height or the engine's air intake, do not proceed and choose an alternative route instead.

20

3

Share

Which Turn Signal to Use When Making a Right U-turn?

When making a right U-turn, you should not use the left turn signal but the right turn signal. The turn signal should indicate the direction of the U-turn. It's important to note that the signal should be activated in advance. Slowing down and signaling only when reaching the intersection can cause sudden interference for vehicles behind. If the following driver is not paying full attention, it may lead to a traffic accident. Precautions for U-turns: When making a U-turn, you should activate the left turn signal in advance, and the maximum speed should not exceed 30 kilometers per hour. Do not obstruct other vehicles or pedestrians traveling normally. Circumstances where U-turns are prohibited: U-turns are prohibited where there are "No U-turn" or "No Left Turn" signs: If there is a sign prohibiting U-turns, then U-turns are not allowed at that intersection. Since a U-turn is an extension of a left turn, intersections with "No Left Turn" signs also prohibit U-turns. U-turns are prohibited at crosswalks: U-turns are not allowed at crosswalks. If the intersection permits U-turns, you must cross the crosswalk before turning around, and you cannot make the U-turn on the crosswalk. U-turns are prohibited when there is no left-turn lane: Even in the leftmost lane, if there is no sign permitting left turns, U-turns are not allowed. U-turns are prohibited in the second left-turn lane: When a vehicle is in the second left-turn lane, it cannot make a U-turn. In the absence of any signs, U-turns are only permitted in the innermost left-turn lane. U-turns are prohibited at solid yellow lines: U-turns are not allowed at solid yellow lines. Even if there is a sign permitting U-turns, you must wait for the green light and cross the stop line before making the turn. U-turns are prohibited on highways: Making a U-turn by crossing the central divider on a highway is illegal and will result in a fine and 12 penalty points. If you miss an exit on the highway, continue to the next exit and leave the highway. Never attempt an illegal U-turn.

5

Share

Why Does a Manual Transmission Car Shudder When Starting?

Manual transmission starting shudder is generally caused by the wear and slippage of the clutch pressure plate and disc, mostly due to aging or quality issues. This requires replacing both the pressure plate and the disc simultaneously. If the driver is a beginner, the idle speed of driving school cars is usually higher, allowing smooth movement without pressing the accelerator. However, almost all manual transmission cars on the market require gently pressing the accelerator when starting. The details are as follows: 1. Fault Handling: Car starting shudder is a very common phenomenon, and there are many reasons that can cause it, either due to faults in the car itself or the driver's poor driving habits. Only after identifying the cause of the starting shudder can timely fault handling be performed. 2. Causes of Shudder: When a car starting shudder occurs, it is essential to carefully investigate the cause, as different shudder phenomena have different reasons. In case of starting shudder, it is recommended to let the engine idle, engage a low gear, slowly release the clutch pedal, and increase the throttle to start. If the body shakes significantly, it indicates clutch shudder. It could also be caused by broken or loose rivets on the driven plate, fractures in the driven plate steel sheet, or unbalanced rotating components. Additionally, loose engine mounts or misalignment between the transmission's first shaft and the engine crankshaft can also lead to car starting shudder.

15

0

Share

What Causes the Noise When Releasing the Brake?

The reasons for abnormal noise when releasing the brake are as follows: 1. Slow brake release: This noise mainly occurs when the brake is released too slowly during startup, which is a common issue for many automatic transmission car owners. When the brake pedal is released gradually, the engine already has sufficient power to drive the car forward, but the brake hasn't been fully released yet. As a result, the moving wheels are held back by the brake system, naturally causing abnormal noise. So next time, remember to release the brake a bit faster. 2. Rust bonding between the brake disc and brake pads causing noise: This usually happens after driving in the rain and then leaving the car unused for several days. The brake disc and brake pads rust and stick together, producing noise when the car is started again. This can be resolved by applying butter or specialized lubricant to the connection between the brake pads and the brake caliper at a repair shop. 3. Metallic noise: Many brake pads nowadays are made of semi-metallic materials, containing a large number of metal fibers. Sometimes, metal particles form, creating a harsh noise when pressing or releasing the brake. This noise usually disappears after driving for a while. If it persists, it may indicate poor manufacturing quality, and it is recommended to replace the brake pads promptly to avoid damaging the brake disc.

15

4

Share

What does it mean when the EPC light comes on in a Volkswagen?

Possible reasons for the EPC light being on include: The car's throttle is dirty and needs cleaning. Brake system malfunction, in which case the brake light may also not work. Fuel quality issues, which can trigger the EPC warning light. EPC (Electronic Power Control) stands for Engine Electronic Power Control System. When a sensor malfunctions or detects an abnormal condition, the control system takes corresponding measures based on predefined settings. Below is a detailed explanation of other scenarios that may cause the EPC light to come on: Engine intake system malfunction: The EPC light may illuminate if the engine intake is obstructed or insufficient. Throttle malfunction: Carbon buildup is a common issue with the throttle, and dirt accumulation can also affect airflow, triggering the warning light. Fuel system malfunction: Examples include substandard fuel, degraded fuel, or poor fuel atomization. Engine malfunction: Insufficient engine pressure or issues with components like the intake valve can also activate the EPC light. ECU control unit malfunction: Such as interference with the onboard computer signals or false alarms from the computer. Brake light malfunction: Issues like non-functional brake lights, faulty brake switches, or wiring problems. Solutions for when the EPC light comes on: Troubleshoot intake system issues, use fuel of the appropriate grade, clean the throttle, etc. Remove carbon deposits from relevant components. Re-flash ECU data. If the EPC light comes on, the driver can first try turning off the engine and restarting it to see if the light remains off. If it does not reappear, the issue may have been temporary. However, if the light stays on or frequently reappears, the vehicle should be taken to the nearest service center for professional diagnosis and repair to eliminate potential safety hazards. The full English name for EPC is Electronic-Power-Control, which translates to electronic power control. Most people refer to it as the engine electronic stability system. The EPC system primarily consists of controllers and sensors related to the powertrain. When sensor data is abnormal, the EPC system takes predefined actions to manage the powertrain. Common EPC indicator lights come in two colors: yellow and red. A yellow EPC light indicates a fault, but the vehicle can still be driven cautiously to a repair shop. A red EPC light signifies a serious issue, requiring immediate parking and contacting a professional for repairs. Continuing to drive under these conditions may damage core components or compromise safety.

20

0

Share

What is the tire size of the Changan Uni-K?

The Changan Uni-K comes with three tire size options: 255/50R20, 255/55R19, and 265/45R21. In 255/50R20, the first number 255 indicates the tire width is 255mm, 50 represents the aspect ratio of the tire section at 50% (meaning the section height is 50% of the width), 20 denotes the rim diameter is 20 inches, and the middle letter "R" stands for radial tire. In 255/55R19, the first number 255 indicates the tire width is 255mm, 55 represents the aspect ratio of the tire section at 55% (meaning the section height is 55% of the width), 19 denotes the rim diameter is 19 inches, and the middle letter "R" stands for radial tire. In 265/45R21, the first number 265 indicates the tire width is 265mm, 45 represents the aspect ratio of the tire section at 45% (meaning the section height is 45% of the width), 21 denotes the rim diameter is 21 inches, and the middle letter "R" stands for radial tire. The Changan Uni-K is equipped with Continental MC6 tires, which feature a wide tread and thin sidewalls, providing strong grip performance. Additionally, the spare tire is full-size. If you wish to replace the tires yourself, follow these steps: Retrieve the spare tire and jack, position the jack under the vehicle frame near the tire to be replaced, ensuring it contacts the metal part of the frame. Raise the jack until it supports the vehicle, making sure the jack is positioned directly under the car and perpendicular to the ground. Remove the hubcap and loosen the nuts counterclockwise. Do not fully remove the nuts; just loosen them enough to reduce resistance. Keeping the tire on the ground while loosening ensures the nuts turn, not the tire. Continue turning the nuts counterclockwise until they are loose. Repeat this step for all lug nuts, then remove them completely. Place the new tire onto the wheel hub, carefully aligning the tire rim with the wheel bolts. Install the lug nuts and hand-tighten them until all nuts are snug. The tire replacement is now complete. In addition to the size, tires also display the following common information: Tire cord material: Indicated by Chinese pinyin, such as M for cotton cord, R for rayon cord, N for nylon cord, G for steel cord, and ZG for steel radial cord. Speed rating: Indicates the maximum speed at which the tire can carry a specified load under defined conditions. Letters A to Z represent certified speed ratings from 4.8 km/h to 300 km/h. Common speed ratings include: Q: 160 km/h; H: 210 km/h; V: 240 km/h; W: 270 km/h; Y: 300 km/h. Rim specification: Indicates the rim size compatible with the tire for practical use, such as "Standard Rim 5.00F."

16

2

Share

Where is Dayang Motorcycle Produced?

What is the wading depth of the Audi A4?

Which Turn Signal to Use When Making a Right U-turn?

Why Does a Manual Transmission Car Shudder When Starting?

What Causes the Noise When Releasing the Brake?

What does it mean when the EPC light comes on in a Volkswagen?

What is the tire size of the Changan Uni-K?

Should you use the left turn signal when making a right U-turn?

What is the usage method of automotive brake fluid?

What is the general pressure for car air conditioning?

What is the tire pressure for a 4.2-meter truck?