Where Does the Rainwater on the Car's Front Windshield Drain From?

1 Answers
AlejandroAnn
07/29/25 12:40pm
Rainwater on the car's front windshield drains from near the rear of the tires. Below are the relevant details: 1. Introduction: The front windshield drainage holes are typically located between the engine compartment and the windshield, consisting of a row of wide black grilles with specially designed water channels, ultimately directing the flow to exit near the rear of the tires. 2. Risks of Blockage: If the front windshield drainage holes become blocked, excessive water accumulation can overflow the sealing tape and enter the engine compartment. Given that the engine compartment houses numerous critical components, this waterproofing protection is vital. Therefore, it is essential to promptly clear any blockages in these drainage holes.
Was this review help?
5
1
Share
More Forum Discussions

What is the fuel tank capacity of the Volkswagen Polo automatic transmission?

The Volkswagen Polo automatic transmission comes in 1 model with a fuel tank capacity of 42.5L. The Volkswagen Polo automatic transmission is equipped with a 1.5L naturally aspirated engine, a 6-speed automatic transmission, and features front-engine, front-wheel drive. Among vehicles in the same class, the 2021 Honda Fit has a fuel tank capacity of 40L, the 2022 YARiS L Zhixuan has a fuel tank capacity of 42L, and the 2022 YARiS L Zhi Xiang has a fuel tank capacity of 42L. During actual refueling, the amount of fuel may exceed the marked capacity. This is because the fuel tank capacity specified by the manufacturer is measured from the bottom of the tank to the safe fill level, and there is additional space from the safe fill level to the tank opening. This extra space ensures that fuel expansion due to temperature increases does not cause overflow. If fuel is filled up to the tank opening during refueling, the actual refueling amount may exceed the marked capacity. To check the remaining fuel level, drivers can observe the fuel gauge on the right side of the dashboard, which is marked with E (Empty) and F (Full). When the needle is close to E, it indicates low fuel, and when it is near F, it means the fuel level is sufficient.
10
2
Share

How many digits is the VIN?

The VIN is a 17-digit code composed of letters and numbers, known as the Vehicle Identification Number, which identifies the manufacturer, engine, chassis number, and other performance data of the vehicle. The requirements for using the VIN are: 1. Every vehicle must have a VIN; 2. No two vehicles produced within 30 years can have the same VIN; 3. The VIN is located in the front half of the vehicle; 4. The VIN on vehicle components must not be damaged or removed. The meaning of the VIN is: 1. The first digit represents the country or region of production; 2. The second digit represents the manufacturer code; 3. The third digit represents the vehicle type code; 4. Digits 4 to 8 represent vehicle characteristics; 5. The ninth digit is a check digit; 6. The tenth digit represents the model year; 7. The eleventh digit represents the assembly plant; 8. Digits 12 to 17 represent the serial number.
15
1
Share

What does 'shift up at 5 and shift down at 0' mean?

The meaning of 'shift up at 5 and shift down at 0' is: shift to 2nd gear when the speed is above 15km/h, shift to 3rd gear when the speed is above 25km/h, shift to 4th gear when the speed is above 35km/h, shift to 5th gear when the speed is above 45km/h; shift to 4th gear when the speed is below 40km/h, shift to 3rd gear when the speed is below 30km/h, shift to 2nd gear when the speed is below 20km/h, shift to 1st gear when the speed is below 10km/h. The gear shifting operation requires at least 3 shifts to complete the project operation, and each gear shift must match the speed. Below is an introduction to the content of Subject 3 examination: 1. Introduction to Subject 3: Subject 3 includes road driving skill test and safety and civilized driving knowledge test, which is part of the motor vehicle driver's license assessment, and is the abbreviation of the road driving skill and safety and civilized driving knowledge test subjects in the motor vehicle driver's examination. The content of the road driving skill test varies for different types of vehicles. 2. Content of Subject 3 examination: The road driving skill test of Subject 3 generally includes: preparation before getting on the car, light simulation test, starting, driving in a straight line, gear shifting operation, changing lanes, parking by the roadside, going straight through the intersection, turning left at the intersection, turning right at the intersection, passing the pedestrian crossing line, passing the school area, passing the bus station, meeting the car, overtaking, turning around, driving at night; the safety and civilized driving knowledge test generally includes: safety and civilized driving operation requirements, safe driving knowledge under bad weather and complex road conditions, emergency handling methods in case of tire blowout and other emergencies, and handling knowledge after traffic accidents.
12
1
Share

How to Open the Hood of the Encore?

The method to open the hood of the Encore is: 1. Locate the plastic tab on the left side of the driver's footwell and pull it outward; 2. Once the hood slightly lifts, raise the hood and reach inside to press the middle latch to fully open it. The Encore has a body size of 4295mm in length, 1798mm in width, and 1616mm in height, with a wheelbase of 2570mm and a fuel tank capacity of 40 liters. The Encore is equipped with a 1.3T turbocharged engine, delivering a maximum power of 121 kW at 5600 rpm and a maximum torque of 240 Nm between 1500 to 4000 rpm, paired with a CVT continuously variable transmission.
12
4
Share

How to reset the maintenance light on a CC?

To reset the maintenance light on a CC, follow these steps: 1. Turn on the ignition; 2. Use the buttons on the multifunction steering wheel to navigate to Settings, press the OK button to select Maintenance; 3. Press the OK button, choose Reset, then press OK again; 4. When the menu appears confirming the reset of maintenance cycle data, press OK once more to confirm the reset. The CC has the following dimensions: length 4865mm, width 1870mm, height 1459mm, with a wheelbase of 2841mm. It is equipped with a 2.0T turbocharged engine, delivering a maximum power of 137kW and a maximum torque of 320Nm, paired with a 7-speed dual-clutch transmission.
16
3
Share

Do Manual Transmissions Still Require Transmission Fluid Changes?

Manual transmissions do require transmission fluid changes. The replacement method is as follows: 1. Prepare an oil filling bucket and manual transmission fluid; 2. Pour the fluid into the filling bucket; 3. Use tools to loosen the drain plug, allow the fluid to drain completely, then reinstall and tighten the plug; 4. Loosen the filler plug; 5. Place the filling tube into the filler port and use the filling bucket to add transmission fluid; 6. Continue until fluid begins to steadily leak from the port; 7. Tighten the drain plug. Transmission fluid is an oil product that maintains the cleanliness of the gear system, ensuring proper transmission operation and extending the lifespan of the transmission components. The maintenance methods for manual transmissions include: 1. Mastering the correct transmission fluid change intervals; 2. Properly replacing the transmission fluid; 3. Regularly checking whether the transmission fluid level is normal.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.