···
Log in / Register

Where are the drain holes on the Avalon's doors?

4Answers
DelMolly
07/28/2025, 08:53:28 AM

Detailed introduction is as follows: 1. Drain holes: The Avalon has three drain holes at the bottom of each door, located inside the sealing strip. Two of these drain holes are already open and do not require manual opening, while the third one is blocked with a rubber plug, which can be removed by hand. 2. Timely cleaning: Each door typically has more than two drain holes, usually located at the lower part of the door panel. If these are not cleared, water can accumulate inside the door, leading to rust over time. Additionally, the door contains various components, including the window regulator and wiring for the car audio system, which can be damaged if exposed to water. Since the drain holes on the door are positioned low, they can easily get clogged with mud when driving on muddy roads. Therefore, it is essential to clean the door drain holes promptly. 3. Important notes: There are several other drain holes on the car that require attention, such as the air conditioning drain hole, engine compartment drain hole, sunroof drain hole, trunk drain hole, and fuel tank cap drain hole.

Was this review help?
111
Share
SanZachary
08/11/2025, 01:35:14 PM

After running this auto repair shop for so many years, I've noticed that the door drain hole locations are pretty similar across Toyota models. The Avalon has four drain holes at the bottom of each door, right where the rubber seal meets the metal door panel. If you squat down and look at the very bottom edge of the door, those half-centimeter wide slits are what you're looking for. Last month, I worked on a flood-damaged car where all four door drains were completely clogged with chewing gum - rainwater accumulated inside the doors and rusted out the window regulators. Remember to use your car key to clear these drain holes whenever you wash your car, especially for vehicles parked under trees. Fallen leaves are the most common culprits for blocking drains, and standing water inside doors will eventually lead to mold growth.

Was this review help?
3
Share
Expand All
LeCali
09/28/2025, 03:43:16 AM

Just yesterday, I cleared the drainage holes on my wife's Avalon, and I remember their locations very clearly. They're right at the very bottom of the door. If you run your fingers along the black dust seal, you'll feel four raised plastic tabs, and the gap in the middle is specifically for drainage. Last week when I washed the car, I noticed the passenger side floor mat was damp, and later found out it was because leaves stuck in the door gap had blocked the drainage hole. I recommend using a thin wire to poke through them every month. The rear door drainage holes are positioned further in, so you'll need to crouch down lower to see them. Oh, and one more thing—don't let the car wash high-pressure water jet spray directly at the drainage holes, as it can easily dislodge the waterproof membrane.

Was this review help?
20
Share
Expand All
DelMarley
11/11/2025, 09:49:28 PM

From the perspective of body structure design principles, the arrangement of drainage holes must balance sealing performance and functionality. The Camry's door drainage holes are located in the inner lining interlayer at the bottom of all four doors, utilizing a gravity self-draining design. Specifically positioned at the junction between the door metal panel and interior trim panel, these 5-8cm long slit-shaped structures maintain a safe distance from door anti-collision beams but are prone to mud clogging. When window-down water accumulation in the inner drainage channel exceeds threshold, fluid discharges through these preset openings. Routine maintenance involves checking drainage sounds: slowly pour 200ml water into window gaps - normal drainage should produce audible water flow within 3 seconds.

Was this review help?
16
Share
Expand All
More Q&A

What are the color options for the CFMOTO 250SR?

The CFMOTO 250SR comes in various color options including blue-orange, silver-orange, silver-green, silver-red, silver with golden rims, track edition cement gray, pink, and the Eva Unit-01 color scheme. Appearance: The sharp front-end design features an imposing face, while the streamlined side profile exudes a fashionable aesthetic. The slightly tapered rear end accentuates the owner's understated yet refined taste. The rear lights adopt the latest design style, delivering a more dynamic illumination effect. Performance: The CFMOTO 250SR is powered by a single-cylinder liquid-cooled engine with a displacement of 249cc, equipped with electronic fuel injection, achieving a class-leading torque of 22 Nm and a maximum power output of 20.5KW. It features a 6-speed chain transmission, consistent with mainstream models. Dimensions: 2010x750x1080mm, with a seat height of 780mm ensuring ample legroom for the rider. The ground clearance of 150mm allows easy navigation through most domestic road conditions, and the 1360mm wheelbase combined with a low seat height ensures effortless handling. Motorcycles consist of five main components: the engine, transmission system, running gear, steering, braking system, and electrical instrumentation. The overall structure and component names of motorcycles. The modern motorcycle industry has incorporated numerous advanced technologies, with engines being either two-stroke or four-stroke gasoline engines. For example, the FLHRC-1 model introduced by Harley-Davidson in 1998 utilized world-class automotive engine technology—fuel injection—enhancing performance while meeting contemporary environmental standards, making it a pioneer for 21st-century motorcycles. High-tech features such as optical communication electronic control systems, radar distance automatic control systems, electronic map navigation systems, and acoustic wave electronic muffler systems in some concept motorcycles have made modern motorcycles more advanced and impressive. Cooling is achieved through air cooling, which can be natural or forced. Most models rely on natural air cooling, where air flowing over the cylinder head and fins on the cylinder liner dissipates heat. High-power motorcycle engines use forced air cooling with fans and air ducts to ensure cooling at low speeds or before starting.
112
Share

Do You Need to Press the Accelerator When Turning or Making a U-Turn?

It depends on the actual situation. Pressing the accelerator is only for controlling the speed, and sometimes you may need to press the brake when making a U-turn. Steering wheel control is crucial when turning. If you want to make a tight turn, you should turn the steering wheel as much as possible and then gradually straighten it after completing the turn. For a wide turn, slowly turn the steering wheel. Be mindful of blind spots when turning; always check for obstacles below the rearview mirror and, if necessary, open the door to look before turning. Additional tips: 1. Make left turns as wide as possible: Some vehicles might be exiting the road you intend to turn into. To avoid obstruction or collisions, try to turn into a farther point. When making a right turn, you might encounter vehicles going straight, such as at intersections. In such cases, make a tight turn to avoid interfering with the straight-moving traffic. 2. The longer the vehicle, the larger the turning radius, and the higher the risk: Large trucks and construction vehicles, due to their height and size, can create significant blind spots when turning right. The driver, seated on the left side, relies on the rearview mirror to observe the right rear, which offers limited visibility. Small objects like electric bikes, bicycles, and pedestrians might go unnoticed. Entering the inner wheel's blind spot can be dangerous.
107
Share

How to Drive After Remote Starting the Buick LaCrosse?

First press the lock button on the car key, then press and hold the remote start button on the car key to start the vehicle's engine. If the driver does not enter the vehicle within ten minutes, the engine will automatically shut off. If the driver enters the vehicle within ten minutes, they need to press the brake pedal and then press the engine start button located at the lower right side of the steering wheel.
114
Share

What to Do When the Haval Car's Network is Disconnected?

Turn on the Bluetooth function of your phone to achieve pairing and interconnection. The name and pairing password will be displayed on the interface of the car's navigation system. Enable the data connection and personal hotspot on your phone so that the car's system can smoothly find and connect to your phone when the wireless WiFi is turned on. If the connection is unsuccessful, try turning off the "Personal Hotspot" on your phone and then turning it back on. Repeat this process a few times if necessary. Click the "AirPlay Mirroring" icon, and your phone screen will prompt the screen mirroring options.
113
Share

Can I Change the Rims if the Rear Wheels Have Drum Brakes?

It is possible to change the rims even if the rear wheels have drum brakes. Requirements for filing the modification: In principle, modifying rims is not allowed, so filing for the modification is necessary. Before making any changes, it is advisable to consult with the local vehicle management office to understand the specific requirements; otherwise, the vehicle may fail the annual inspection. Legal basis for changing rims: According to the 'Regulations on the Registration of Motor Vehicles,' any modifications to the body color, model, performance, purpose, or structure of a licensed vehicle, including replacing the frame, body, or engine, must be reported to the vehicle management office for registration changes. If the new rims are of the same size, they will generally pass the annual inspection, but the appearance should not be significantly altered.
118
Share

What is the reason for cleaning carbon deposits in a car?

The reason for cleaning carbon deposits in a car is to prevent the internal components of the engine from being clogged, thereby avoiding any impact on the normal operation of the engine. Methods for cleaning carbon deposits in a car: Remove the engine cover, take off the throttle valve, clean it with carburetor cleaner, dry it with a cotton cloth, and then reinstall it; open the oil cap, pour in the entire can of cleaning agent, close the oil cap, start the engine and let it idle for ten minutes before turning it off; pour the intake system cleaner into the storage tank of a dedicated cleaning device, connect it to the intake system, and start the engine to use vacuum to draw the cleaner into the intake tract for cleaning purposes. Methods to identify carbon deposits in a car: Check the fuel consumption—if the increase is continuous, it indicates that carbon deposits have formed on the engine; based on the mileage, the higher the car's mileage, the more carbon deposits will accumulate; switch to a higher-grade gasoline—if there is an improvement in power, it indicates that the engine has significant carbon deposits.
117
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.