What was the emission standard for trucks in 2014?

1 Answers
VanAubrey
07/29/25 4:33pm
Most trucks in 2014 complied with China IV emission standards, but this depends on specific circumstances. Methods to check a vehicle's emission standard: 1. Check the motor vehicle certificate: New vehicles come with a compliance certificate that clearly states the emission standard. 2. Review the vehicle documentation: The emission standard can be found in the vehicle information section of the accompanying documents. Introduction to China IV emission standard: The China IV standard upgraded the exhaust after-treatment system compared to China III, reducing pollutant emissions by 50-60%. Compared to China IV, the China V standard reduces nitrogen oxide emissions by 25% and introduces additional restrictions on non-methane hydrocarbons and particulate matter emissions to reduce air pollution and combat smog.
Was this review help?
1
3
Share
More Forum Discussions

What does it mean when a tire pressure sensor is lost?

Tire pressure sensor loss is generally caused by damage to the sensor, and replacing the sensor will resolve the issue. Below is an introduction to tire pressure sensors: 1. Introduction: A sensor is a detection device that can sense the measured information and convert the sensed information into electrical signals or other required forms of information output according to certain rules, to meet the requirements of information transmission, processing, storage, display, recording, and control. 2. Principle: By installing a tire pressure monitoring sensor inside each wheel, the sensor wirelessly transmits the tire's pressure and temperature values to the body controller according to a certain pattern. The BCM then sends the information frame to the dashboard via the CAN bus, allowing the driver to obtain the pressure and temperature values of each tire through the dashboard display.
2
3
Share

Should I Get the Free Clutch Replacement from Volkswagen?

If the clutch is functioning properly, replacement is unnecessary. However, if issues are present and the vehicle is still under warranty, replacement is recommended. Below is an introduction to clutches: 1. Definition: Located within the flywheel housing between the engine and transmission, the clutch assembly is secured to the rear plane of the flywheel with screws. It serves as a device that switches the engine power of automobiles or other machinery on or off to the axle. 2. Function: The driver can depress or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine with the transmission, thereby cutting off or transmitting the engine's power input to the transmission. 3. Position: Installed between the engine and transmission, the clutch is the assembly component in the vehicle's drivetrain that directly connects to the engine. Typically mounted together with the engine crankshaft's flywheel group, it acts as the component that disconnects and transmits power between the engine and the vehicle's drivetrain. Throughout the process from starting the vehicle to normal driving, the driver can operate the clutch as needed to temporarily separate or gradually engage the engine with the drivetrain, cutting off or transmitting the engine's power output to the drivetrain.
15
3
Share

Differences and Similarities Between Positive Profile Shift Gears and Standard Gears

Differences and similarities between positive profile shift gears and standard gears are as follows: 1. Difference: Positive profile shift gears utilize the upper portion of the involute curve (away from the base circle center), resulting in a straighter involute profile. 2. Similarity: Both standard gears and positive profile shift gears share the same base circle. When gear parameters (number of teeth, module, pressure angle) are identical, standard gears and profile shifted gears have identical involute curves. The module, number of teeth, and pressure angle of profile shifted gears are the same as standard gears, and their pitch circles are also identical. Below is extended information about gears: 1. Gears with non-standard involute tooth profiles are produced by altering the radial position of standard cutters relative to the gear blank or modifying the tooth space width of standard cutters. 2. Radial modification refers to changing the standard cutter's radial position relative to the gear blank during tooth cutting, while tangential modification involves altering the tooth space width of standard cutters. Radial modification is most commonly used, whereas tangential modification is typically applied to bevel gears. 3. When using rack-type cutters to manufacture gears, if standard installation is not employed but the cutter is positioned farther from or closer to the gear blank's rotation center, the cutter's reference line will no longer be tangent to the pitch circle of the gear being processed.
12
4
Share

When is the Guangzhou Auto Show?

The 19th Guangzhou Auto Show (the last major international auto show of the year) is expected to be held from November 19th to November 28th at the China Import and Export Fair Complex in Pazhou. Details are as follows: 1. Organizers: Guangzhou Municipal People's Government, Guangdong Provincial Economic and Information Technology Commission, China Foreign Trade Centre, China Machinery Industry Federation, China Association of Automobile Manufacturers. 2. Co-organizers: China Foreign Trade Guangzhou Exhibition Corporation, Automotive Sub-Council of China Council for the Promotion of International Trade, Guangzhou Automobile Industry Group Co., Ltd., China Society of Automotive Engineers, Guangzhou United Exhibition & Trade Co., Ltd., Guangzhou Sub-Council of China Council for the Promotion of International Trade, Guangzhou Automobile Dealers Association, Guangzhou Federation of Industrial Economics.
11
5
Share

How to Determine the Parking Points for Reversing into the Garage in Subject 2?

When the lower edge of the left rearview mirror aligns with the yellow garage boundary line, you can press the clutch and brake. However, the prerequisite for doing this correctly is adjusting the seat and rearview mirror positions properly. Relevant details are as follows: 1. Assessment Item: Reversing into the garage is a mandatory test item for obtaining a small car driver's license after 2013. It assesses the driver's ability to maneuver the vehicle in a confined space. Reversing into the garage is a key evaluation point in the driver's test, requiring the driver to correctly reverse the vehicle into the garage from both sides while moving. 2. Reversing Methods: There are three most common types of reversing. The first is the "non"-shaped reversing into the garage, commonly seen in large parking lots. The second is the "one"-shaped reversing into the garage along the roadside, also known as parallel parking. The third is the less common diagonal reversing into the garage. About 70% of driving students find parallel parking more challenging.
1
0
Share

How to Use the Roof Rack on a Car?

Items or luggage on the roof rack should be tightly secured or fastened, and evenly distributed. If they lack elasticity, a cargo net should be added. During driving, emergency braking should be avoided as much as possible. The load-bearing design of roof racks is generally 30 to 50 kilograms, and the weight of objects must not exceed the designed load capacity when in use. Relevant details are as follows: 1. Function: Car roof racks combine aesthetic and practical functions, enhancing the vehicle's appearance while being highly useful during trips. They can carry items that don't fit in the trunk, such as large luggage, bicycles, folding beds, etc. As long as the owner secures the cargo properly, especially by adding a cargo net, more items can be transported. 2. Classification: Based on size and features, car roof racks can be categorized into single-layer racks, double-layer racks, Australian-style racks, and luxury racks. By vehicle type, they can be divided into specialized racks and universal racks. By installation method, they can be classified into simple racks and modular racks.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.