What type of oil is used in the Haval F7 from the factory?

1 Answers
MacChloe
07/30/25 4:40am
Haval F7 uses fully synthetic oil with a viscosity of 40 from the factory. Lift the car: Jack up the car, then remove the car's underbody shield, and place a container of about 10 liters under the oil drain plug. Loosen the oil drain plug to drain the oil: Unscrew the car's oil drain plug, blow air into the oil filler port with an air gun for two to three minutes. After the oil is completely drained, tighten the oil drain plug and wipe it with a tissue to check for any leaks. Reinstall the shield and add new oil: Reinstall the car's underbody shield, gently lower the car, and finally, use a funnel to add new oil into the oil filler port.
Was this review help?
4
4
Share
More Forum Discussions

How long is the battery warranty for the Trumpchi GS4?

The battery warranty period for the Trumpchi GS4 is one year. Within this one-year period, any quality issues will result in a free replacement. Car batteries are sensitive to low temperatures—under cold conditions, a battery's capacity is significantly lower than at normal temperatures. Therefore, regular inspection and maintenance are essential. Daily care tips include: 1. Avoid parking the car in open-air parking lots for extended periods. If long-term parking is unavoidable, remove the battery to prevent freezing damage. 2. In winter, car engines are harder to start. Each attempt to start the engine should not exceed 5 seconds, with at least a 15-second interval between attempts. If the engine fails to start after several tries, check other potential issues like the electrical circuit, ignition coil, or fuel system. Avoid continuous unsuccessful starts, as this can over-discharge and damage the battery. 3. Regularly charge the car battery. A battery left unused will gradually self-discharge and eventually become unusable. Thus, start the car periodically to recharge the battery. 4. Clean the battery terminals periodically and apply specialized grease to protect the wiring harness. Routinely inspect the battery's components and connections. 5. Avoid using car electronics when the engine is off. Using the battery alone without the engine generating power can cause harm.
2
3
Share

What is the Scrap Life of a Family Car?

There is no usage period limit for passenger cars. When the normal mileage reaches 600,000 kilometers, the state will guide the vehicle to be scrapped. Vehicle scrapping process: 1. The car owner applying for scrapping and renewal must fill out an "Application Form for Vehicle Modification, Transfer, Alteration, Suspension, or Scrapping" and affix the owner's seal. 2. Apply at the registration acceptance counter. For vehicles that have reached the scrapping age, a "Vehicle Scrapping Notice" will be issued. For vehicles that have not reached the scrapping age but are deemed to meet the scrapping standards after inspection by the vehicle inspection counter, a "Vehicle Scrapping Notice" will be issued. 3. The owner can choose a qualified recycling company to dismantle the vehicle with the "Notice". 4. After verifying the "Notice", the recycling company will dismantle the vehicle and take photos. The engine must be separated from the vehicle, the engine block must be broken, and the frame (chassis) must be cut. 5. The owner must submit the "Modification Form", "XX Province Vehicle Renewal Technical Appraisal Form", "Scrapped Vehicle Recycling Certificate", and photos of the dismantled vehicle to the vehicle inspection counter for verification and signature. The license plates will be reclaimed, and the application will be submitted for approval according to regulations to complete the scrapping registration.
9
5
Share

What is the break-in period mileage for the Infiniti QX50?

The break-in period for the Infiniti QX50 is 3,000 kilometers. Before vehicle assembly, each moving component is processed separately, and geometric deviations exist during the machining of parts. Therefore, after assembly, some moving parts may have direct local contact, making it difficult for lubricating oil to reach the friction surfaces, resulting in early wear. The process of wearing away metal debris and burrs from parts when the car is first used is called the break-in period. Below are precautions to take during the new car break-in period: 1. Avoid high-speed driving: New cars have speed limits during the initial driving phase. Domestic vehicles are generally limited to 40-70 km/h, while imported vehicles typically require that within the first 1,000 kilometers, the speed should not exceed 80% of the maximum speed when the throttle is fully open. Additionally, it is important to monitor the engine tachometer and speedometer to ensure the engine and vehicle operate at medium speeds. Generally, the engine speed during the break-in period should be strictly maintained between 2,000 and 4,000 rpm. 2. Throttle and brake usage during the break-in period: Learn to control the depth of the throttle during the break-in period. Pressing the throttle deeply increases air intake, which in turn increases fuel injection, potentially damaging internal components. Frequent hard braking can also cause excessive wear on the braking system. 3. Avoid emergency braking: Emergency braking not only shocks the braking system during the break-in period but also increases the impact load on the chassis and engine. Therefore, it is recommended not to use emergency braking within the first 300 kilometers of driving.
19
1
Share

What brand of engine is used in the Buick Excelle?

The engine of the Buick Excelle is produced at the Shanghai General Motors Yantai Dongyue Base, featuring German technology and is a domestically manufactured engine. The Buick Excelle uses the L2B engine model, with a maximum horsepower of 113Ps, a maximum power output of 83KW, a maximum power speed of 6000rpm, and a peak torque of 141N.m. For daily maintenance of the Buick Excelle's engine, the following methods can be employed: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly replace the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine issues. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. As oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, it may burst the filter element or open the safety valve, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
1
4
Share

What is the maximum load capacity of the Boyue?

The maximum load capacity of the Boyue is 2045kg. The Boyue is a compact SUV under Geely. Taking the 2021 Boyue as an example, its body dimensions are: length 4519mm, width 1831mm, height 1694mm, wheelbase 2670mm, fuel tank capacity 58l, and curb weight 1575kg. The 2021 Boyue is equipped with a 1.8T turbocharged engine, with a maximum power of 120kW and a maximum torque of 250Nm, matched with a 6-speed manual transmission. It adopts a front suspension type of MacPherson independent suspension and a rear suspension type of multi-link independent suspension.
2
0
Share

What transmission does the BMW 3 Series use?

The BMW 3 Series uses an 8-speed automatic manual transmission. The BMW 3 Series is a mid-size car launched by BMW, equipped with a 2.0T turbocharged engine, paired with an 8-speed automatic manual transmission. The BMW 3 Series is a new generation sedan product from BMW Group, with a body weight of 1465 kg, an inline 4-cylinder gasoline engine, and body dimensions of 4734mm in length, 1811mm in width, and 1455mm in height. The 8-speed automatic manual transmission means the transmission has 8 forward gears, allowing drivers to use manual mode or automatic mode during driving.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.