What to Do About a Dent in the Car Door?

What Causes Steering Wheel Bearing Noise?

There is an issue with the steering switch. Here are the specific details: 1. The shock absorber bearing is making noise: When turning the steering wheel, if the noise comes from outside the vehicle, check if it is coming from the shock absorber area. If so, it is likely due to insufficient lubrication in the bearing. If the noise persists after applying grease to the shock absorber's plain bearing, the only solution is to replace it at a repair shop. 2. Aging of the steering tie rod ball joint: An aging steering tie rod ball joint can also cause noise in the steering wheel. The main reason is excessive play in the tie rod, leading to steering wheel noise. This issue usually cannot be repaired and requires replacing the steering tie rod ball joint to resolve the noise. However, remember to perform a wheel alignment after replacement. Alternatively, the noise could be due to loose or worn stabilizer bar bushings. Loose or damaged stabilizer bar bushings not only cause noise when turning the steering wheel but also when driving on rough roads. If the stabilizer bar bushings are only loose, adding shims can solve the problem. If they are damaged, replacement is necessary.

4

Share

What Causes Antifreeze to Change Color?

If the antifreeze changes color, it is likely due to deterioration, which not only reduces its antifreeze properties but also diminishes its cooling effect on the engine. Here are the specific details: 1. Regular Replacement: When the engine operates at high temperatures without effective cooling, the viscosity of the engine oil decreases, leading to wear and tear on engine components over time. In severe cases, the engine may even be rendered unusable. Given the high cost of engine repairs, it's crucial to adhere to the antifreeze replacement schedule. 2. Radiator Issues: Another possible cause is the mixing of antifreeze with engine oil, which can occur due to problems with the oil radiator or filter, or possibly due to seal aging. While the consequences may not be as severe as antifreeze deterioration, it still affects performance. Don't wait until the engine overheats ('boiling over') to take action; visit an auto repair shop as soon as possible for a fix.

13

1

Share

What Causes Engine Stall During Starting in Subject 2?

Here are the reasons for engine stall during starting in Subject 2: 1. Releasing the clutch too quickly: The solution is to slowly release the clutch, pause momentarily when the car moves slightly, and then continue to release the clutch gradually. Also, avoid turning the steering wheel during startup; any necessary turns should be made after the car starts moving. 2. Starting in gear: This basic mistake often occurs due to exam nerves, so develop the habit of starting in neutral during practice. 3. Forgetting to release the handbrake: It's advised not to engage the handbrake midway. Forgetting to release it at the beginning will cause immediate failure. Ensure the handbrake is fully released. When braking in first or second gear, pay attention to controlling the force, and coordinate with the clutch at low speeds.

9

3

Share

How to Check the Production Date of Maxxis Tires?

Tire production dates are indicated by a four-digit number, which is printed on the sidewall of the tire. The first two digits represent the week of production, and the last two digits indicate the year. For example, the number 1019 means the tire was produced in the 10th week of 2019. Here are some usage recommendations for tires: 1. When purchasing tires, always check the production date. Avoid buying tires with production dates that are too old. 2. Tires are made of rubber and will age even if not used. 3. Regularly check the tire pressure and inspect the tire surface for any damage during normal use. 4. The sidewall of a tire is relatively fragile. If the sidewall is scratched or punctured, it cannot be repaired. It is recommended to replace tires every four years, even if the mileage driven within those four years is low.

18

2

Share

Should You Signal or Brake First When Turning in Subject 3?

When turning in Subject 3, you should signal first and then brake. Signaling first is mandatory because traffic laws require the use of turn signals when turning, and you must activate the turn signal at least 50 meters before the intersection to alert vehicles behind you. Therefore, you should signal before slowing down. Additional information about Subject 3 is as follows: 1. Test Content: For large buses, tractors, city buses, medium-sized buses, large trucks, small cars, small automatic transmission cars, low-speed trucks, and small automatic transmission cars for the disabled, the test includes preparation before starting, simulated nighttime lighting test, starting, driving straight, shifting gears, changing lanes, parking by the roadside, going straight through intersections, turning left at intersections, turning right at intersections, crossing pedestrian crossings, passing school zones, passing bus stops, meeting oncoming traffic, overtaking, making U-turns, and nighttime driving. The test content for other permitted vehicle types is determined by the provincial traffic management authorities of the public security department. 2. Large Vehicles: For large buses, tractors, city buses, medium-sized buses, and large trucks, provincial traffic management authorities of the public security department should add complex road driving test content, such as mountainous areas, tunnels, and steep slopes, based on actual conditions.

8

1

Share

What to Do When the EA888 Engine Cooling System is Insufficient?

Here is more information about the EA888 engine: 1. The EA888 series engines include two displacements: 1.8L and 2.0L. The 1.8TSI has a maximum power of 118kw at 5000-6200rpm and a maximum torque of 250Nm at 1500-4500rpm. The 2.0TSI can reach a maximum power of 147kw at 5100-6000rpm and a maximum torque of 280Nm at 1700-5000rpm. 2. The mechanical structures of these two displacement engines are basically the same, with the difference lying in the length of the connecting rods between the crankshaft and pistons. The connecting rods of the 2.0TSI are shorter than those of the 1.8TSI, and the crankshaft radius is increased to enhance the displacement.

16

4

Share

What to Do About a Dent in the Car Door?

What Causes Steering Wheel Bearing Noise?

What Causes Antifreeze to Change Color?

What Causes Engine Stall During Starting in Subject 2?

How to Check the Production Date of Maxxis Tires?

Should You Signal or Brake First When Turning in Subject 3?

What to Do When the EA888 Engine Cooling System is Insufficient?

Can small bubbles in car paint be polished?

What Materials Are Cars Made Of?

What Causes Low Engine RPM?

Does the steering wheel have a ventilation function?