What should be paid attention to when a car is not used for a long time?

1 Answers
VanLilah
07/30/25 2:14am
When a car is not used for a long time, it is necessary to wash the car thoroughly before parking, and then apply a sealant or wax to the body, which helps prevent the paint surface from being corroded and oxidized. Then choose a suitable parking location. If the parking time is short, waxing is sufficient; if the time is longer, it is recommended to cover the car with a car cover. When a car is parked for a long time, the tires will suffer significant damage. It is essential to choose a flat ground for parking. Otherwise, if parked on uneven ground for a long time, the tires may deform due to uneven force. Before using the car again, carefully check whether the tires are deformed or cracked, and also check whether the tire pressure is normal, as the tires will slowly lose air. If the car is parked for a long time, there is no need to refuel temporarily. Keep a small amount of fuel in the tank to avoid excessive water in the tank due to humid weather. A high water content in the tank can easily cause many problems, especially in places where ethanol gasoline is used, so extra attention should be paid. It is recommended to use a water remover regularly. In addition, the car battery will discharge on its own. If the car is not used for a long time, the battery may lose power, and it may not start when ignited again. You can charge the car battery regularly, start the car every 1-2 weeks and let it run for 5-10 minutes, or you can disconnect the negative terminal of the battery to minimize power consumption.
Was this review help?
13
4
Share
More Forum Discussions

What is the speed limit on curves?

When driving on sharp curves, the maximum speed should not exceed 30 kilometers per hour. Speeding poses risks, so safety must be prioritized while driving. Introduction to the risks of speeding: The dangers of speeding on curves are not limited to the increased likelihood of rollovers. More importantly, curves often have large blind spots, and if there is oncoming traffic, the probability of severe accidents resulting in fatalities is significantly higher. Driving precautions: Before entering a curve, honking can alert potential oncoming vehicles. It is crucial to control speed and maintain a safe distance while driving. Keeping a safe distance is essential, and drivers should also look ahead to assess road conditions and surroundings.
7
2
Share

Where is the suspension stiffness adjustment button for the Avalon?

The Avalon does not provide a button for suspension stiffness adjustment, as it employs an automatic suspension stiffness adjustment system. Below are the detailed specifications of the Avalon: 1. The Avalon features a sporty design overall and is classified as a mid-size sedan. 2. The Avalon offers two engine displacement options: 2.0L and 2.5L. The maximum horsepower is 178ps and 209ps, respectively; the maximum power output is 131kw and 154kw; and the maximum torque is 221N·m and 250N·m. 3. The fuel options include hybrid and gasoline, with the gasoline version requiring 92-octane fuel. The emission standards meet China 5 and China 6. The transmission options include E-CVT continuously variable transmission, CVT continuously variable transmission, and an 8-speed automatic transmission with manual mode.
11
4
Share

Is 90 Degrees Celsius Normal for Cummins Engine Coolant Temperature?

The normal operating temperature is around 90°C. Below are the common causes of overheating: Insufficient coolant: Coolant leakage can cause temperature rise. In this case, check for any signs of coolant leakage. If found, promptly repair the leaking pipes or components. If no leaks are detected, replenish with the same brand of coolant. Adding water is not recommended, especially in winter, as it can dilute the coolant even if it doesn't cause immediate malfunctions. Radiator fan malfunction: A faulty radiator fan may prevent proper heat dissipation during high-speed operation, causing heat to accumulate instead of transferring to the antifreeze. This leads to increased antifreeze temperature and potential boiling-over issues. If this occurs while driving, first reduce vehicle speed. Inspect whether the fan is functioning properly. If faulty, repair it immediately rather than waiting for the coolant to boil.
1
4
Share

What is the wading depth of new energy vehicles?

10CM. Currently, the only clearly defined standard for the wading depth of new energy vehicles is the national standard GB/T18383.3. This standard specifies that the wading depth for new energy vehicles should be 10CM, with a speed of 20KM/h, a travel distance of 500m, and a wading time of 1.5min. Below are the relevant details: Wading test standards: In fact, local regions also have their own wading test standards for new energy vehicles. For example, Shanghai's pure electric vehicle admission policy includes the mandatory DB31T634-2012 standard, which requires simulating the wading conditions during vehicle operation. Pure electric vehicles must drive through 15 centimeters of water at a speed of over 30km/h for a total wading time of 10 minutes. Then, in 30 centimeters of water, they must drive forward and backward at a speed of no less than 5km/h for a total wading time of 10 minutes. This test further ensures that new energy vehicles have sufficient safety for driving. Additionally, Beijing has its own local standard for electric vehicles, defining a wading depth of 20CM. Test methods: Furthermore, according to the "Safety Requirements and Test Methods for Power Batteries in Electric Vehicles" issued by the General Administration of Quality Supervision, Inspection and Quarantine, clear safety indicators and test methods are provided for individual power batteries and modules of new energy vehicles. Among these test methods, it is required that saltwater can easily corrode products. Battery cells, in a fully charged state, should be soaked in a 3.5% NaCL (sodium chloride, simulating seawater) solution for 2 hours without any incidents such as fire or explosion.
17
5
Share

Should the clutch be fully released before accelerating after shifting gears?

After shifting gears, the clutch should be fully released before accelerating. Introduction to the car clutch: The clutch is located in the flywheel housing between the engine and the transmission. The clutch assembly is fixed to the rear plane of the flywheel with screws, and the output shaft of the clutch is the input shaft of the transmission. The clutch is one of the important components of a car. Introduction to the car throttle: Also known as the "air throttle" or "throttle valve," it refers to the control device that regulates the engine power (thrust). In piston aircraft engines, the throttle controls the opening of the carburetor's throttle valve to regulate the cylinder's weight, thereby determining the engine's output power.
5
2
Share

Where is the rear wiper located on the oldest Buick GL8 model?

The switch for the rear wiper on the oldest GL8 model is located on the right-hand stalk behind the steering wheel. Below are the specific steps for replacing the rear wiper on a Buick GL8: 1. Remove the wiper blade, open the hood, and unscrew the fixing bolts on the cover plate. 2. Peel off the hood seal, lift the hood, disconnect the spray pipe connection, and remove the cover plate. 3. Unscrew the bolts under the cover plate and remove the inner plastic panel. 4. Disconnect the motor plug, unscrew the bolts on both sides of the linkage rod, and then pull it out. 5. Remove the motor from the old linkage rod and install it onto the new one. Insert the assembly back into the rubber hole of the linkage rod, tighten the screws, reconnect the motor plug, and finally restore the seal and cover plate.
7
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.