···
Log in / Register

What procedures are required for transferring driving schools?

1Answers
VanAdrian
07/29/2025, 02:52:51 PM

The procedures required for transferring driving schools are as follows: 1. The student must obtain a transfer certificate from the original driving school. 2. Then, retrieve their personal file from the vehicle management office or the driving school. 3. Finally, report to the new driving school with the file and transfer certificate. Below is relevant information: The cost calculation for student transfers is as follows: 1. If the student has not taken any subject exams and applies for a transfer due to personal reasons, they will be required to pay 20% of the tuition fee as a penalty. 2. If transferring after failing the subject one exam, a file establishment and service fee of 250 yuan and a theoretical training fee of 150 yuan will be deducted. 3. If the driving school fails to arrange a subject two exam for students who have passed subject one within 60 days, a full refund can be claimed. 4. If the student has participated in subject two training, with training hours not exceeding one-third of the total subject two hours and not exceeding the 90-day training period, in addition to deducting the file establishment, service fee, and theoretical training fee, an actual vehicle training fee of 60-80 yuan per hour will also be deducted. 5. No refund will be issued if the student has completed subject two due to personal reasons or has exceeded the stipulated time limit due to personal reasons.

Was this review help?
116
Share
More Q&A

Will the Brake Discs of a New Car Rust?

Brake discs can rust, which is not a quality issue with the car, nor does it indicate that the car has been in stock for a long time. This is a normal phenomenon. Since brake discs are primarily made of iron and lack any anti-rust treatment, they will rust when exposed to moisture in the air. Solution for Slight Rust: If the brake discs have slight rust, it can usually be removed through normal braking. The principle is that the friction between the brake pads and the brake discs will wear away the rust. After braking a few times, the brake discs will shine like new. If there are areas the brake pads don't reach, you can remove the wheel and use fine sandpaper to polish the brake disc. Solution for Heavy Rust: If the corrosion is severe, relying on the braking system to remove the rust may not be effective, especially if the car has been left idle for an extended period, making the rust more stubborn. In such cases, the car should be taken to a specialized repair shop for professional servicing by a technician. If the rust is extremely severe, the brake discs may need to be removed and professionally polished or resurfaced.
114
Share

How long does it take to repair a small dent in car sheet metal?

If the dent on the car is relatively small, the repair time is approximately one hour. Here is relevant information about automotive sheet metal repair: 1. Material Requirements: Sheet metal materials must have excellent plasticity, meaning the ability to undergo permanent deformation under external forces without being damaged. For cold-worked components, good cold plasticity is required, such as automotive stamped parts; for hot-worked components, good thermal plasticity is necessary, such as hot-forged spring steel plates and hot-riveted rivets. The material should also have good weldability, ensuring high welding strength and low cracking tendency. It should be cost-effective and economically practical. Additionally, it must possess good chemical stability and maintain precise dimensional accuracy and internal quality of the sheet. 2. Concept: Automotive sheet metal repair involves the complete restoration of faulty or damaged vehicle bodies.
119
Share

Will the Engine Stall in Fourth Gear Without Accelerating?

If the vehicle is already in motion and shifted into fourth gear, it can continue to run without pressing the accelerator, but the speed will gradually decrease. Once the speed drops to a certain level, the car will start to shake and eventually stall. Fourth Gear in Cars: The fourth gear in a car is a driving gear primarily used for prolonged high-speed and economical driving. The most fuel-efficient speed for most vehicles typically occurs in the lower speed range of fourth gear, generally between 45-56 km/h. Gear Shifting Principle: Manual transmission vehicles achieve gear ratio changes by switching different gear sets. As a key component in power distribution, the transmission must have two main parts: the power input shaft and the output shaft, along with the gears that make up the transmission. These are the most basic components of a manual transmission. Car Accelerator: The accelerator in a gasoline engine primarily controls the throttle opening size. A smaller opening means less air-fuel mixture enters the cylinder, resulting in lower engine power output, and vice versa. The more air-fuel mixture enters the cylinder, the greater the combustion force, which in turn increases the force pushing the piston, speeds up piston movement, and consequently increases engine speed.
106
Share

What is the fuel consumption in Phase IV?

In Phase IV, the average fuel consumption of passenger vehicles in China was 5.0 liters per 100 kilometers. Research Background: After a long period of development, China's commercial vehicle market has entered a period of rapid growth in the past decade, with the development of heavy-duty commercial vehicles being particularly remarkable. However, the high pollution and high fuel consumption caused by heavy-duty commercial vehicles have also been persistent concerns. To curb the high fuel consumption of heavy-duty commercial vehicles and promote the adoption and use of clean technologies in commercial vehicles, China has introduced a series of fuel consumption limit standards for commercial vehicles over the past decade. Phase IV Fuel Consumption: The Phase IV fuel consumption standard for commercial vehicles in China is a crucial step in promoting the development of the commercial vehicle industry. The selection of driving cycles is particularly important. It is recommended to further introduce slope testing in the bench testing of fuel consumption standards, which will improve the alignment between fuel consumption standards and actual driving conditions. Additionally, it will encourage the adoption of more advanced energy-saving auxiliary technologies in new vehicle models.
104
Share

What Oil Can Replace Hydraulic Oil?

Engine oil, gear oil, or transmission oil can be used. Here is some relevant information about hydraulic oil: 1. Characteristics: It has good anti-foaming properties, ensuring stable power transmission and preventing accelerated oxidation of the hydraulic oil. It also has excellent rust prevention and oxidation stability, making it less prone to oxidation and degradation, thus extending its service life. It has suitable viscosity and good viscosity-temperature performance, enabling accurate and sensitive power transmission while ensuring normal lubrication of hydraulic components. 2. Function: Hydraulic oil is the hydraulic medium used in hydraulic systems that utilize liquid pressure energy. It plays roles in energy transmission, wear resistance, system lubrication, corrosion prevention, rust prevention, and cooling within the hydraulic system.
105
Share

What is the symbol for airbags?

The airbag symbol depicts a seated figure holding a round object, and this warning light indicates whether there is a fault in the vehicle's airbag system. Function of airbags: The airbag system is a passive safety protection system that, when used in conjunction with seat belts, provides effective collision protection for occupants. In the event of a car collision, airbags can reduce head injuries by 25% and facial injuries by approximately 80%. Working principle: The sensor system continuously sends speed change information to the control unit, which analyzes and evaluates this data. Reasons for the airbag warning light to illuminate: Engine self-check; airbag sensor malfunction; airbag control unit malfunction; poor electrical connection.
116
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.