···
Log in / Register

What maintenance does an Audi need at 20,000 kilometers?

3 Answers
DeRiley
08/30/25 5:21am
Maintenance items include engine oil and oil filter, air filter, external cabin air filter, and spark plugs. The fuel filter should be inspected during every maintenance service and replaced if necessary. Develop the habit of regular maintenance: Extend the vehicle's lifespan. During driving, many components operate under harsh conditions such as high temperatures, high speeds, dusty environments, and bumpy roads. Some parts experience continuous wear due to constant high-speed movement, while others may get damaged unexpectedly. This necessitates timely inspection, adjustment, or replacement through regular maintenance. Regular maintenance primarily focuses on inspection and adjustment: Periodic checks of the braking, steering, drivetrain, and suspension systems are included in every type of maintenance service, ensuring a safe driving environment. Through regular inspections and maintenance, potential hazards and faults can be promptly identified and resolved, preventing major breakdowns.
Was this review help?
16
4
Share
SanCora
09/12/25 2:30am
I've been driving an Audi for many years, and every 20,000 kilometers, I have to go for maintenance. The most important thing is to change the engine oil and oil filter, which is crucial for engine protection. Otherwise, increased wear can easily lead to problems. The air filter also needs to be replaced to prevent dust clogging, which affects fuel consumption and power. Tires should be checked for pressure and wear, and their positions should be rotated to avoid uneven wear and extend their lifespan. The braking system must never be neglected; check the thickness of the brake pads, disc wear, and fluid level to ensure responsive and safe braking. Test the lights and wipers for safer nighttime driving. Tighten the chassis screws and inspect the suspension to prevent bumps at high speeds. I always ask the mechanic to replace the cabin air filter before the season changes to keep the interior air fresh. The dealership also performs a computer diagnostic to check for fault codes. Although it costs a bit more, it’s worry-free. I usually learn some basic knowledge on my own, like checking tire pressure regularly and avoiding long trips to save money. After maintenance, drive gently for a few hundred kilometers without sudden acceleration, and the car can last many more years.
Was this review help?
2
5
Share
Expand All
McRonan
10/26/25 3:20am
As a cost-conscious car owner, my Audi's 20,000-kilometer maintenance basically includes changing the engine oil and filter, as well as the air and cabin air filters. Buying these parts myself and having a repair shop install them is cheaper. Fresh oil keeps the engine running smoothly, while new filters prevent dust from damaging the car. Replacing the cabin air filter improves air quality inside the car, making long drives more comfortable. Tires must be checked, rotated, and balanced to save on replacement costs. Brake system inspection, including pads, discs, and fluid levels, is crucial for safety. Checking and tightening chassis bolts reduces vibration and noise. Lighting tests prevent nighttime accidents. Computer diagnostics help detect hidden faults early, saving money on unnecessary repairs. Follow the manual for regular maintenance to avoid accelerated engine wear. Routine care like washing the car to remove rust can extend its lifespan and save money. After maintenance, pay attention to whether the engine starts smoothly and fix minor issues promptly.
Was this review help?
10
4
Share
Expand All
More Forum Discussions

What procedures are required for inspecting a gas cylinder?

Inspecting a gas cylinder requires the gas cylinder usage registration certificate from the oil-to-gas conversion, the gas cylinder factory qualification certificate, the gas cylinder installation supervision inspection certificate, the vehicle's driving license, and the owner's ID card. Below is relevant information about the gas cylinder: 1. Function of the gas cylinder: When the rotor and lubricating oil rotate, suction is generated to draw out the internal pressure air produced during braking in the booster, which then returns to the oil reservoir along with the lubricating oil through the oil return line. The lubricating oil settles, and the air is discharged through the exhaust hole on the upper cover, improving the safety performance of the braking system. 2. Materials required for the annual inspection of the gas cylinder: For the gas cylinder inspection, the following materials need to be prepared: one copy of the "Motor Vehicle Registration Certificate," one copy of the "Vehicle Driving License," one copy of the "Gas Cylinder Usage Registration Certificate," and the "Gas Cylinder Qualification Certificate."
7
3
Share

Where are the sensors located on the Nissan Teana?

Nissan Teana sensors are located in the following positions: 1. Oxygen Sensor: The oxygen sensor is installed on the exhaust pipe to monitor the post-combustion gases and determine whether the engine combustion is sufficient and whether the mixture is too lean or too rich. 2. Wheel Speed Sensor: It primarily collects the vehicle's speed to detect any signs of wheel slippage. Therefore, there is a dedicated sensor to gather wheel speed data, usually installed on the hub of each wheel. If the sensor fails, the ABS system will become ineffective. 3. Coolant Temperature Sensor: The coolant temperature sensor is typically located near the thermostat. It converts the coolant temperature into an electrical signal, increasing fuel injection or advancing the ignition timing at low temperatures, while preventing detonation and retarding the ignition timing at high temperatures. 4. Intake Pressure Sensor: Generally installed near the throttle body, the intake pressure sensor detects changes in resistance and pressure corresponding to different engine speeds and loads, converting these into voltage signals for the ECU to adjust fuel injection and ignition timing.
2
3
Share

How to Replace the Wiper Blades on a Lavida?

The method for replacing the wiper blades on a Lavida is as follows: 1. After turning off the vehicle, do not remove the key immediately. Within 3 seconds, pull the wiper control lever inward, and the wipers will move to the maintenance position. 2. Gently pull the wiper arm toward the front of the vehicle until it locks into place. Press the silver button on the wiper arm, hold the wiper blade, and pull it outward with slight force to remove the old rubber blade. 3. Release the two clips and remove the old rubber blade. 4. When installing the new rubber blade, remember to stagger the two metal pieces and ensure it is inserted into the first groove. The process is slightly tedious and requires patience; install one side first before proceeding to the other. 5. After successful installation, follow the reverse order of the removal steps to complete the wiper blade installation.
20
1
Share

How Hard is Carbon Fiber?

Carbon fiber material is an ultra-hard substance that is 10 times harder than ordinary steel, second only to the hardness of diamond. Below is a relevant introduction to carbon fiber: 1. Composition of Carbon Fiber: Carbon fiber is formed by stacking organic polymer fibers with extremely high carbon content along the fiber bundle direction. The currently recognized high hardness and ultra-strong shear resistance are not entirely due to material properties. There is a decisive factor involved—the critical void. When the stacking between fibers is below a certain critical value, the void index between fibers determines the hardness, shear resistance, and tensile strength of the fiber. 2. Reasons for Hardness Reduction: The critical porosity that causes a decline in material mechanical properties is 1%–4%. When the void volume content is within the range of 0–4%, for every 1% increase in void volume content, the interlaminar shear strength decreases by approximately 7%. Moreover, higher porosity leads to larger void sizes, significantly reducing the area of interlaminar interfaces in the laminate. When the material is under stress, it is prone to failure along the layers, which is why interlaminar shear strength is relatively sensitive to porosity.
8
4
Share

Are Passat Seat Heating and Seat Ventilation the Same?

Passat seat heating and seat ventilation are not the same functions. Seat heating refers to the electric heating device inside the seat. Seat ventilation is the "summer cooling device" of the car seat air conditioning, which is divided into air supply type and air suction type. More details are as follows: 1. The car seat air conditioning system includes ventilation circulation, dehumidification and cooling/heating, and intelligent temperature control, completely eliminating the discomfort caused by the seat being hot and sticky in summer and cold in winter while driving. 2. As an effective supplement to the car air conditioning system, the car seat air conditioning system can adjust the temperature and humidity of the seat surface, maximizing the satisfaction of different drivers and passengers' requirements for seat surface temperature in different seasons, helping them maintain full energy and clear reaction ability. According to statistics, it can save fuel consumption by an average of 7-9%. 3. The car seat air conditioning system is divided into two types: external and built-in. Seat heating uses electric heating wires inside the seat to heat the seat interior and transfers the heat to the occupant through heat conduction, improving the discomfort caused by the seat being too cold after long periods of parking in winter.
13
2
Share

How to use the GAC GS3 navigation system?

GAC GS3 navigation system usage method is as follows: 1. The GAC GS3 center console panel adopts a snap-on design. For complete removal, a pry bar and a Phillips screwdriver are required. 2. Start prying from the bottom of the center console panel. After prying it open, remove the wiring harness and take out the original radio panel. 3. Install the navigation system by connecting the plugs. If unsure, refer to the car navigation manual for guidance. 4. Install the GPS receiving antenna and the rearview camera. 5. Route the rearview camera wiring harness along the door edge seal to the rear seats, then fold down the rear seats and pass it through to the trunk. 6. Install the rearview camera inside the license plate light, then route the camera wiring harness back and complete the installation. 7. Test for any issues. If everything is normal, reinstall in the reverse order of removal.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.