What lights should be turned on in time when driving in rainy days?

1 Answers
RobertLynn
07/28/25 11:37pm
When driving in rainy days, headlights, clearance lights and rear position lights should be turned on in time. At the beginning of the rain, the sky is relatively dark, but the visibility is still good. At this time, the width indicator lights should be used. When the rain is heavy, the rainwater itself will block the driver's sight, and the water on the road will be rolled up by the rolling tires of the vehicle in front, forming a water mist, which will also greatly affect the visibility. At this time, the headlights or front fog lights should be turned on. In the case of heavy rain or rainstorm, some sections of the road will be seriously flooded in a very short time. If you have to wade through the water, you should use low gear to pass at a constant speed. If the vehicle stalls while moving, never try to start it again. Blind starting may cause the engine to be scrapped.
Was this review help?
5
4
Share
More Forum Discussions

What is the function of a car front lip?

The functions of a car front lip include: 1. It can perform overall vehicle streamlining; 2. Reduce airflow passing under the vehicle; 3. Improve vehicle stability; 4. Enhance the aesthetic appeal of the car. The overall vehicle streamlining ensures that air flows evenly from the front to the rear of the car, reducing frontal turbulence, which can lower the cd value and increase front-end downforce, with more noticeable effects at high speeds. Reducing the airflow under the vehicle can decrease the lift caused by the airflow beneath the car. Generally, the higher the vehicle body, the more unstable it becomes at high speeds. Modifying the car front lip alters the car's appearance and requires registration with the vehicle management office; otherwise, the car may face difficulties passing the annual inspection.
5
1
Share

Honda Lingpai has power but won't start with one-button ignition?

Honda Lingpai has power but won't start with one-button ignition may be caused by reasons such as the gear not being in P position, fuel pump failure, key issues, or starter motor failure. Detailed explanations are as follows: 1. Gear not in P position: More and more vehicle models are now factory-set to prevent ignition when not in P position for safety considerations. This is mainly to prevent the car from lurching forward when ignition occurs in D or R gear. Solution: Shift to P position and restart. 2. Key issues: If it's related to the key, there could be multiple causes, such as interference with the key's radio waves. 3. Fuel pump failure: Similar to running out of fuel, a damaged fuel pump can also prevent the car from starting. The starter motor operates normally during ignition, but the engine won't start. If there's no fuel pressure in the fuel lines, it's definitely a fuel pump failure. 4. Starter motor failure: A damaged starter motor can also prevent ignition, similar to a dead battery, with no response during ignition. 5. Excessive carbon buildup in the throttle body: When the accelerator is not pressed, the throttle body leaves only a small gap for air to pass through. If this gap is clogged with excessive carbon buildup, air cannot pass through, preventing ignition. In this case, slightly pressing the accelerator during ignition can help the car start smoothly. 6. Crankshaft position sensor failure: This sensor monitors the crankshaft position to determine ignition timing and is also known as the speed sensor. If damaged, the engine control unit (ECU) won't receive speed signals during ignition and thus won't control the spark plugs to ignite, as the ECU simply doesn't know ignition is being attempted.
14
5
Share

How to Drain Windshield Washer Fluid from a Sedan?

Methods to drain windshield washer fluid from a sedan: 1. Start the car and press the windshield washer button until the fluid is completely sprayed out. However, this method is not recommended when there is a large amount of remaining fluid. Avoid continuous pressing; instead, press intermittently. 2. Some cars have a dedicated drain valve—simply open it to release the fluid. 3. Siphon method: Prepare a soft tube longer than 2 meters and a syringe. First, open the car's hood and locate the windshield washer fluid reservoir cap (usually blue with a water spray symbol). Open the cap, insert the tube as far as possible, and use the syringe to start siphoning. When the fluid reaches the level of the headlights, remove the syringe and place the tube on the ground. The remaining fluid will automatically drain out. 4. There is usually a black plastic windshield washer tube in the engine compartment. Open the hood, locate the tube, disconnect one end, and spray the fluid outward from the car.
4
2
Share

Is It Safe to Drive with a Noisy Differential?

It is advisable not to continue driving if the differential is making unusual noises. You should promptly take your vehicle to an auto repair shop for inspection. After lifting the vehicle, if the noise persists when braking either drive wheel, it rules out wheel bearing or brake system issues. If replacing the drive axle does not eliminate the noise, it excludes axle faults. If the noise only occurs during turns, it is likely differential-related. Possible causes of differential noise include: 1. Poor gear meshing, loose spline fit between the side gear and axle; 2. Overly loose or tight bearings; 3. Excessive wear of differential components; 4. Improper gear meshing clearance or incorrect gear contact patterns.
20
2
Share

What does it mean when the bulb failure warning light comes on?

Bulb damage or lighting circuit malfunction, it is recommended to have the vehicle's entire lighting system inspected at a repair shop. The lights that most commonly fail on vehicles include: headlights, turn signals, brake lights, etc. Below is relevant information about vehicle lights: 1. Vehicle lights refer to the lamps on a vehicle, serving as tools for road illumination during nighttime driving and as signaling devices for various vehicle movements. 2. The most vulnerable aspect of vehicle lights is water ingress. If the light seals are compromised, moisture vapor can easily accumulate, leading to filament burnout and discoloration of reflective surfaces, resulting in faulty light projection. To prevent abnormal light failures, proper usage and maintenance should be observed.
1
3
Share

What is the 0-100km/h acceleration time of the MG6 Pro?

The MG6 Pro achieves a 0-100km/h acceleration in just 8 seconds. It is equipped with SAIC's Blue Core 2.0 MEGA-Tech next-generation powertrain combination, primarily targeting young consumers. The new vehicle features a pure black large-sized polygonal front grille, split-type headlight clusters with the upper section housing daytime running lights and turn signals, while the high/low beam headlights are relocated to concealed positions on either side of the grille. Below is more detailed information: 1. Exterior: The vehicle adopts a four-door hatchback design with dark black five-spoke large-sized alloy wheels paired with red single-piston calipers. It features dual exhaust pipes, a large rear spoiler, and smoked treatments for the chrome strip between the taillights and the taillights themselves. 2. Features: The car comes with a three-spoke multifunction steering wheel, a full LCD instrument cluster, a 10.1-inch frameless suspension control screen, and an electronic gear shift mechanism. The interior uses a dual-tone color scheme with bright orange accents. It offers two driving modes, including Super-Sport mode with one-touch activation, switchable sport exhaust, dynamic curve control system, and electric power steering. The vehicle is also equipped with the latest operating system, air conditioning, and a vehicle connectivity system. 3. Powertrain: The new model is powered by a Mega-Tech 1.5T high-performance engine delivering a maximum power of 133kW and peak torque of 285N·m, paired with a 7-speed dual-clutch transmission boasting 97% efficiency, enabling the 0-100km/h sprint in 8 seconds.
8
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.