What kind of engine oil is suitable for the Changan CS55?

2 Answers
JohnnyAnn
07/25/25 4:22pm
Changan CS55 can use 5W40 full synthetic engine oil or 0W40 full synthetic engine oil. Engine oil, also known as engine lubricant, serves multiple functions such as lubrication and wear reduction, auxiliary cooling, sealing and leakage prevention, rust and corrosion protection, as well as shock absorption. Qualified engine oil can reduce wear on engine components and extend the engine's service life. The Changan CS55 is an SUV model under Changan Automobile, with body dimensions of 4500mm in length, 1855mm in width, and 1690mm in height, and a wheelbase of 2650mm. In terms of power, the vehicle is equipped with a 1.5T turbocharged all-aluminum engine, model JL476ZQCD. For body colors, it primarily offers Dynamic Red and Starry Blue as the main options.
Was this review help?
6
0
Share
StWyatt
08/11/25 9:48pm
I've been driving the Changan CS55 for several years, and routine maintenance has been quite straightforward. For engine oil, I recommend using a full synthetic 5W-30—its moderate viscosity handles seasonal changes well, especially protecting the engine during summer heat or winter cold starts. Don’t skimp by using mineral oil; its shorter change intervals mean frequent trips to the shop and higher costs. I usually opt for brands like Shell or Castrol, purchased through official channels, changing it every 7,000–10,000 km—it’s actually more cost-effective and hassle-free in the long run. Always glance at the user manual for specific guidance to avoid issues like increased noise or fuel consumption from using the wrong oil. Remember, regular upkeep is key to keeping your car in top shape.
Was this review help?
2
2
Share
Expand All
More Forum Discussions

What does it mean when the ABS light comes on in a car?

ABS light can indicate various conditions, each with different causes and solutions. The details are as follows: Condition 1: ABS warning light stays on (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting its ability to detect the vehicle's speed signal. This prevents the ABS computer from determining the speed and wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose connections in the system wiring or poor contact in the ABS relay can cause signal issues, leading to system failure. Solution: Check the wiring connections and reconnect any loose parts. Condition 2: ABS warning light intermittently comes on but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage may drop below 10.5V. As the engine speed increases, the voltage rises, and the ABS light turns off. This can also happen if the ABS system's power supply voltage is too low due to poor contact or grounding issues. Solution: Check the battery's condition, the charging system, and the power supply (e.g., voltage relay or poor power contact). Condition 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wiring connector; ABS computer malfunction. Solution: Loosen and retighten the grounding screw of the hydraulic valve body, cleaning the contact surface if necessary. Check for enlarged gaps in the connector. Replace the ABS or ABS/ASR computer if needed. Condition 4: ABS warning light comes on during high-speed driving. Cause: The ABS computer detects a significant difference between the rear and front wheel speeds during high-speed driving. This may be due to incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, usually listed on a sticker near the fuel tank cap. Condition 5: ABS warning light intermittently comes on. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, and push the brake switch lever down with your finger to its limit. Release the brake pedal to complete the self-setting position. Replace the brake light switch if necessary. If the ABS warning light is on, it is recommended not to continue driving. A lit ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks.
6
3
Share

What to Do When the Car Washer Nozzle Has Weak Water Spray?

Solutions for weak water spray from car washer nozzle: 1. Determine whether the issue is on one side or both sides. If it's on one side, it is usually caused by a clogged nozzle on that side. Solution: Use a sewing needle, pin, or very thin wire to poke the nozzle, spray out the remaining washer fluid, and then use an air gun to blow through the clogged nozzle. 2. Check the motor and its wiring. Have one person operate the washer button inside the car while another opens the engine compartment to listen for any sound from the washer motor. If there is sound, the motor may be faulty. If there is no sound, the motor itself is likely defective. Solution: First, check if the filter is clogged. A clogged filter can be repaired by removing the water hose connected to the nozzle, opening the washer fluid filler port, and using an air gun to blow through the hose. This will force the washer fluid out through the filler port and remove any debris stuck on the filter. If the motor is faulty, it must be replaced.
8
5
Share

What Materials Are Needed for Car Polishing?

Materials used for car polishing include a polishing machine, polishing pads such as wool pads, rabbit hair pads, sponge pads, etc., polishing compounds, masking film, paper tape, etc. Generally, after polishing is completed, waxing, sealing, or coating is required. The steps for car polishing are as follows: 1. Wash the entire car. Use a paint cleaner with strong decontamination power to clean the entire car. When using the cleaner, avoid causing new scratches from particle dust during the polishing process. 2. Sand with water sandpaper. For defects such as coarse particles, fine sandpaper marks, or flow marks on the paint surface, use 600#-1000# water sandpaper wrapped around a small rubber block to gently sand the surface until smooth before polishing. Be careful not to sand through the paint layer. 3. Coarse and fine grinding. Use a mechanical grinder with coarse polishing compound to grind away the marks left by the water sandpaper, then add fine polishing compound for fine polishing. 4. Polishing. Use a mechanical polisher with a mirror finish compound to remove the swirl marks left by the coarse polishing compound, achieving a mirror-like finish on the paint film. 5. Manual polishing. After grinding and polishing, wipe off the polishing compound and immediately use a cotton cloth soaked in polishing wax to wipe the polished areas. Then, use a dry cotton cloth to remove any excess wax, leaving the paint surface bright and dazzling like a mirror.
6
1
Share

What is the izda car?

Toyota does not have a car named izda. The similar name is izoa, which is called Yize in Chinese. It is a compact SUV produced by FAW Toyota. The following is an introduction to Yize: 1. The entire series is equipped with a 2.0L Dynamic-Force-Engine, which is the first TNGA honeycomb concept SUV from FAW Toyota. 2. The 2021 Yize is an annual facelift model, not a generational change. This model adds the Yize Sport Edition, featuring exclusive sports kits, 17-inch smoked black aluminum alloy cutting wheels, exclusive silver-black Branno leather seats, and a unique silver-black roof body color, creating a strong visual sense of sportiness. 3. In terms of power, the new car still uses a 2.0L naturally aspirated engine with a maximum power of 126 kW and a maximum torque of 203 Nm. 4. In terms of the transmission system, it is matched with a CVT gearbox. From the powertrain perspective, this 2.0L plus CVT combination is used in many Toyota models, such as the Toyota Avalon and Toyota Camry. In terms of chassis tuning, models built on the TNGA platform have a chassis tuning that leans towards German cars, creating a strong sense of premium and stability during driving.
5
1
Share

Where are the instrument panel lights on the Ford Focus?

Focus instrument panel lights are located on the dashboard below the steering wheel. Instrument panel lights are functional lamps used to indicate vehicle performance, and they are divided into three categories: general indicator lights, warning indicator lights, and fault indicator lights. The reasons why instrument panel lights cannot be turned off and their solutions are as follows: 1. Automatic illumination: The instrument panel lights remain on after closing the car door, which is one of the car's functions. They will turn off after locking the car; 2. Non-automatic illumination: The instrument panel lights change with the headlight switch. When the headlights are turned off, the instrument panel lights will naturally turn off; 3. Fault lights: A fault in a certain component inside the car, such as the engine, oil, braking system, water temperature, etc. These require troubleshooting and the use of a decoder to clear the fault codes before the lights will turn off; 4. Reminder lights: These remind that the car door, front hood, rear hood, etc., are not closed properly. Simply handle the relevant components according to the reminder light's prompt.
11
4
Share

When is a car considered a China IV vehicle?

China IV emission standards began in 2011 and lasted until 2018 when China V standards were implemented. Therefore, vehicles produced between 2011 and 2017 all meet China IV standards. The China IV standards require approximately 50% lower emissions of various pollutants compared to China III standards. Here are the relevant details: The China IV emission standard is the fourth phase of national motor vehicle pollutant emission standards in China. The main pollutants emitted by vehicles include HC (hydrocarbons), NOx (nitrogen oxides), CO (carbon monoxide), and PM (particulate matter). Through the application of technologies such as improved catalytic converter active layers, secondary air injection, and exhaust gas recirculation systems with cooling devices, the standards aim to control and reduce vehicle emissions to below specified levels.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.