What kind of engine does the Peugeot 3008 have?

What is the correct ignition method for a key-start car?

Sit in the driver's seat and press the start button once. When the ACC light comes on, press the button once more to initiate the vehicle's self-check. Next, press the brake pedal and then press the one-touch start button to ignite and start the engine. Release the foot brake, and you may choose to warm up the car while stationary. Press the foot brake again, shift to D gear, release the handbrake, slowly release the foot brake, and press the accelerator to complete the starting process.

20

1

Share

How to Clean Engine Oil Stains Penetrated into Cement Floor?

Alcohol can dissolve in both organic solvents and water. The higher the alcohol concentration, the better, with anhydrous alcohol being the best option. Alcohol is available at pharmacies or chemical stores. Apply a small amount of essential balm on the clothing area stained with engine oil, and wash it together with the laundry. It's simple and effective for thorough cleaning. First, use gasoline to wipe the stain. For heavier oil stains, you can use paint thinner and turpentine. Once the oil stain dissolves, proceed with regular washing methods to clean it thoroughly. Use a soft cloth or cotton yarn dipped in gasoline to wipe the stain. The oil-based colored substances will dissolve in the gasoline and transfer to the cleaning cloth.

10

0

Share

How to Charge a Li Auto Vehicle?

Open the battery fluid filler cap. Check the electrolyte level, and if it is insufficient, first add distilled water. Connect the red clip to the 12V or 24V terminal as required by the battery. The red and black clips should be connected to the "+" and "-" terminals of the power source, respectively. Connect the "+" and "-" terminals of the battery to the corresponding positive and negative terminals of the charger. Properly connect the charger's power cord to the power outlet. Adjust the charging current using the regulator switch knob. Monitor the ammeter reading. The charging current should be between 10~15A; excessive current may damage the battery.

4

1

Share

Does lugging a manual transmission car affect the vehicle?

Lugging a manual transmission car does affect the vehicle. Prone to stalling: Under lugging conditions, the engine may operate near the critical speed, making it prone to stalling. Weak acceleration: When the engine speed is too low, there will be a phenomenon of weak power output (determined by the power-speed characteristics), resulting in weak acceleration. Increased fuel consumption: If the speed is too low, the car does not cover distance efficiently. Since fuel consumption is calculated based on a per 100 km standard, although the fuel consumption per unit time decreases, it takes several times longer to cover the same distance, leading to an overall increase in fuel consumption. Jerky movement: Insufficient power output while the car is trying to move forward can cause jerky movements, commonly known as "lugging," which can damage the transmission.

8

0

Share

How to Adjust the Audio System of the 3rd Generation Haval H6?

Turn on the head unit and play some high-fidelity vocal tracks or tracks with strong bass dynamics. Adjust the volume to slightly over half or 3/5 of the maximum level. First, increase the GAIN knob of CHANNEL-1/2 until the sound is very loud, then reduce the volume of the head unit. Typically, when the head unit volume is increased, vocals may sound nasal, as if having a cold, or the pronunciation may seem unclear. Regardless of the state of the front sound field, the rear sound field should be set to HP mode, and the CROSSOVER (cutoff frequency) should be adjusted to around 150Hz. Set the FILTER of the subwoofer amplifier to the LP (low-pass) position and adjust the CROSSOVER (cutoff frequency) to the lowest setting.

6

0

Share

Can Chassis Armor Be Sprayed on the Fuel Tank?

Paint can be applied to the fuel tank. Areas where it should not be sprayed: Generally, the chassis armor suitable for your vehicle is sufficient. The area from the beam base to the spare tire base can be sprayed, but the exhaust, suspension, and brake areas should not be painted. Additional Information: Before spraying, cover the brakes and suspension with newspaper, and remove the exhaust, wheels, and other parts. For new cars, the protective wax on the chassis must evaporate completely, and no thinner should be added. After the first coat, let it dry for 10 minutes before applying the second coat. Typically, 3-4 coats are applied, with thicker layers on areas like the fuel tank and fender. After spraying, the car should be parked in a garage to dry for 24 hours, avoiding contact with water. Avoid working in rainy or humid weather, as this can hinder the timely drying of the coating and affect the effectiveness of the chassis armor. After the chassis armor application, it is best not to drive on rough roads for about a day, as the coating may not have fully dried and cured.

13

2

Share

What kind of engine does the Peugeot 3008 have?

What is the correct ignition method for a key-start car?

How to Clean Engine Oil Stains Penetrated into Cement Floor?

How to Charge a Li Auto Vehicle?

Does lugging a manual transmission car affect the vehicle?

How to Adjust the Audio System of the 3rd Generation Haval H6?

Can Chassis Armor Be Sprayed on the Fuel Tank?

Is it easier to pass the driving test in rainy weather?

How to Get Your Vehicle Inspected During the Pandemic?

What is the smallest domestic fuel-powered car?

How early should I apply for a driver's license renewal in another location?