What is the wheelbase of the Yema Spica?

1 Answers
ORemington
07/30/25 6:05am
The wheelbase of the Yema Spica is 2800mm, with dimensions of 4580mm in length, 1730mm in width, and 1825mm in height. The vehicle is equipped with a 1.5L naturally aspirated engine across all variants, delivering a maximum power of 82kW and a peak torque of 136Nm. The engine reaches its maximum power at 5500 rpm and peak torque at 4500 rpm. The Yema Spica is an urban electric MPV under the Yema brand, featuring a sophisticated and stable business-oriented exterior design. Its interior adopts a simple and practical sedan-like layout, offering flexible seating arrangements and spacious cargo capacity.
Was this review help?
5
3
Share
More Forum Discussions

What Causes the Motorcycle Engine Warning Light to Illuminate?

Motorcycle engine warning light illumination is caused by issues such as poor valve sealing, fuel pump circuit malfunctions, and intake system blockages. The specific reasons are as follows: Poor Valve Sealing: Incorrect valve timing, leading to inadequate sealing of intake and exhaust valves. Fuel Pump Circuit Malfunction: Poor performance, short circuits, or burnouts in the fuel pump due to circuit issues, resulting in insufficient or halted fuel supply. Intake System Blockage: Blockages in the intake system, such as in the air filter or mass airflow sensor, preventing complete fuel combustion. Engine Detonation: The primary cause of engine detonation is excessively rapid combustion. Detonation generates excessive impact forces on the pistons, causing wear on the cylinder walls.
6
3
Share

Can a Turbocharger Oil Leak Be Repaired?

If the turbocharger has a severe oil leak, it can only be replaced and cannot be repaired. Here is some relevant information: 1. The turbocharger is a component unique to turbocharged engines and is a very important part of such engines. 2. The turbocharger consists of two parts: one is the intake turbine, and the other is the exhaust turbine. The intake turbine and exhaust turbine are connected coaxially. The exhaust turbine is connected to the exhaust manifold. When the engine reaches a certain speed, the exhaust has enough energy to drive the exhaust turbine to rotate. Once the exhaust turbine starts rotating, the intake turbine also begins to rotate, allowing the intake turbine to compress air and blow it into the engine cylinders. The shaft between the exhaust turbine and intake turbine is immersed in engine oil, which lubricates and cools the shaft.
10
0
Share

Is Subject 2 Difficult to Pass?

If you practice diligently, Subject 2 is quite simple. Below is the relevant introduction: Subject 2: Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment. It is the abbreviation for the field driving skills test. For the C1 license, the test items include five mandatory components: reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving through curves (commonly known as the S-curve). Test Scheduling: In April 2016, the "Decision on Amending the Regulations on the Application and Use of Motor Vehicle Driver's Licenses" was officially implemented. This allows for self-study and direct testing for small cars, and Subjects 2 and 3 can be scheduled and taken consecutively.
12
3
Share

Why is the transmission fluid turning white?

Transmission fluid turning white is caused by water entering the transmission, which requires cleaning the transmission. Hazards of not replacing transmission fluid: 1. Damage to the transmission's shift control mechanism; 2. Abnormal wear of gears and clutch plates inside the transmission; 3. Affects the normal operation of the transmission, leading to damage of the transmission valve body. Transmission fluid is different from engine oil. Although both fluids serve a lubricating function, their roles are distinct and should not be confused. Differences: Engine oil is a lubricant for the engine system, possessing properties such as oxidation resistance, wear resistance, and corrosion prevention. Transmission fluid, on the other hand, is primarily used to keep the gear system clean and extend the service life of internal transmission components. Due to the different structures and operating environments of the transmission and the engine, transmission fluid cannot be used as engine oil, and engine oil cannot be used as transmission fluid.
13
1
Share

Should You Press the Clutch or Brake First When Turning?

When turning, press the brake first to reduce speed, and press the clutch to ensure the car does not stall. Operating requirements when turning: For sharp turns, if the car shakes while braking, downshifting may be necessary. Specific actions depend on the situation. Some intersections have gentle turns where third or fourth gear can be used. Precautions when turning: When turning, adjust the steering wheel according to the road curvature and vehicle speed, ensuring appropriate steering angle, timing, and timely correction. Never remove both hands from the steering wheel to avoid dangerous deviations. Reduce speed when turning and avoid sudden steering to prevent excessive centrifugal force causing skidding. If the car skids, immediately release the accelerator, steer toward the direction of the skid, and once the car straightens, correct the steering wheel and continue driving.
18
3
Share

What are the brands of electric tricycles with 3C certification?

Currently, Wanshida is probably the only company with first-class 3C certification that specializes in producing leisure tricycles and holds over ten patents. Below is the relevant introduction: Wanshida: Tianjin Puzhong Wanshida Technology Co., Ltd. was established on September 29, 2015, with its registered address at No. 11, 1st Road, North District, Jinghai Economic Development Zone, Tianjin, and its legal representative is Lin Xiuhuan. The business scope includes the technology development, manufacturing, processing, wholesale, and retail of bicycles, electric bicycles, motorcycles and their parts, manual tricycles, electric children's vehicles, sports equipment, frames and their accessories, motors, controllers, metal products and their accessories, plastic products, and molds; metal surface treatment (excluding galvanizing). 3C Certification: It is a product conformity assessment system implemented by the Chinese government in accordance with laws and regulations to protect consumer personal safety and national security and to strengthen product quality management.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.