What is the reason for the flashing AC light in Toyota Reiz?

1 Answers
VonHannah
07/30/25 10:45am
The possible reason for the flashing AC light in Reiz is the tripping of the compressor protection device. Excessive refrigerant: Solution: Appropriately reduce the amount of refrigerant. Poor heat dissipation: Solution: Check if there is dust or dirt on the condenser pipe and clean the condenser. Blocked pipeline system: Solution: Refer to the pressure gauge to diagnose and resolve the issue, then reprocess the system. Dust or scale buildup on the evaporator or filter, leading to reduced airflow and imbalance in system pressure and temperature. Solution: Clean the evaporator or filter: When there is a lack of refrigerant, the compressor exhaust temperature will overheat, causing the overload protection switch to trip: Solution: Add refrigerant promptly.
Was this review help?
7
1
Share
More Forum Discussions

Is the Mercedes-Benz G500 the Big G or the Small G?

The Mercedes-Benz G500 is the Big G. Additional information is as follows: 1. Introduction: This purebred off-road vehicle is equipped with Mercedes-Benz's latest generation 5.0L V8 engine, delivering a maximum power of 216kW/5500rpm and a maximum torque of 456Nm/2800-4000rpm. The installation of a supercharger enables it to unleash 80% of its maximum torque at around 1800rpm. Combined with its ladder-frame non-independent suspension and three differential locks (front, center, and rear axles), the G500 boasts formidable off-road capabilities. 2. Interior: In terms of materials and craftsmanship, the G-Class has taken a significant step closer to its traditionally luxurious sedan counterparts, incorporating nearly all the functional features found in sedans. The latest COMAND entertainment system has also been integrated into the walnut wood-inlaid center console.
1
3
Share

What is the power output of the Buick GL8?

The Buick GL8 is available with a 2.0T turbocharged engine and a 2.5L naturally aspirated engine. Additional details are as follows: 1. Powertrain: The new generation Buick GL8 family is equipped with General Motors' latest Smart-Propulsion intelligent drive technology, featuring a flagship powertrain combination of the eighth-generation Ecotec 2.0T variable cylinder turbocharged engine and a 9-speed HYDRA-MATIC intelligent transmission. This setup delivers robust power output of 174kW and 350Nm, with a combined fuel consumption of just 7.9L/7.8L per 100km. 2. Safety Features: The new generation Buick GL8 Avenir family is equipped with the Buick Advanced Intelligent Driving Assistance System, offering 20 advanced intelligent driving assistance functions including LCC Lane Centering Intelligent Cruise Control, TJA Traffic Jam Assist, HOD Hands Off Detection, and DOW Door Open Warning.
9
0
Share

What is the normal tire pressure for the Levin 185T?

The normal tire pressure for the Levin 185T is 2.4-2.5, while the reinforced version is 2.8-2.9. Relevant information is as follows: 1. Influencing factors: Tire pressure is significantly affected by seasonal factors. In summer, high temperatures cause tires to heat up during driving, and high tire pressure can easily lead to blowouts, so the pressure should be slightly lower. In winter, tire pressure should be slightly higher than in summer due to thermal contraction and expansion, making a range of 2.5-2.8 generally suitable. 2. Differences: The tire pressure of a cold tire differs from that of a hot tire, with a difference of approximately 0.2-0.3. In a cold state, the front tire pressure is 2.2-2.3, and the rear tire pressure is 2.4-2.5, but the specific pressure should follow the manufacturer's recommendations. Different car models, due to variations in weight, height, and tire size, require different tire pressures.
1
3
Share

How to turn on the heater in BYD S6?

Method to turn on the heater in BYD S6: 1. Start the car and warm it up for about 15 minutes. When the water temperature is normal, you can turn on the heater, then rotate the temperature control switch to the red area; 2. Adjust the air circulation mode to internal circulation; 3. Switch to the heating mode. Some cars use the red area, while others use a sun symbol; 4. Do not turn on the AC switch, as the heater utilizes the car's own heat cycle to save energy; 5. Adjust the air conditioning to a suitable gear and set the airflow direction; 6. The warm air is usually directed forward and towards the feet, while the cold air is generally directed forward. The BYD S6 is BYD's first SUV, positioned as a mid-to-high-end independent SUV. In terms of body dimensions, the BYD S6 measures 4810mm in length, 1855mm in width, and 1680mm in height.
16
1
Share

What are the differences between the Panamera 4 and Panamera 4S?

Here are the differences between the Panamera 4 and Panamera 4S: 1. Different brake caliper colors: The Panamera 4 has black brake calipers; the Panamera 4S has silver brake calipers. 2. Different body dimensions: The Panamera 4 measures 5015mm in length, 1931mm in width, and 1418mm in height; the Panamera 4S measures 4491mm in length, 1852mm in width, and 1296mm in height. 3. Different top speeds: The Panamera 4 has a top speed of 260km/h; the Panamera 4S has a top speed of 297km/h. 4. Different horsepower: The Panamera 4 uses a 3.0T engine with a maximum horsepower of 320ps; the Panamera 4S also uses a 3.0T engine but with a maximum horsepower of 420ps. 5. Different drive systems: The Panamera 4 is rear-wheel drive; the Panamera 4S is four-wheel drive.
14
1
Share

How to Quickly Patch a Leaking Fuel Tank?

If the fuel tank is leaking, you can clean the leaking area and apply soap or chewing gum to temporarily block the leak. Using epoxy resin adhesive for repair yields better results. Extended knowledge: 1. Apply an appropriate amount of lubrication to the wheel hub bearings, regularly clean and unclog the vent holes and plugs on the rear axle housing to ensure they remain connected to the atmosphere. To prevent the wheel hub from overheating during frequent braking, which can thin the grease, you can sprinkle water on the wheel hub to cool it or install a water spray device. 2. If the oil seal or gasket is damaged or fails, replace it with a new sealing component. If the leak persists, remove the shock absorber. If you feel any sticking or uneven resistance, further inspect whether the gap between the piston and cylinder is too large or if the shock absorber piston rod is bent. 3. All types of fastening nuts on the vehicle should be tightened to the specified torque. Prolonged use of parts can lead to excessive wear (e.g., piston and cylinder), so early maintenance or replacement of worn parts is necessary. 4. To prevent the check valve or vent valve from becoming clogged, perform regular inspections, unclogging, and cleaning of the vehicle.
20
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.