What is the penalty for not driving according to the indicated traffic markings?

1 Answers
SanElliott
07/29/25 10:41am
Not driving according to the indicated traffic markings will result in a deduction of 3 points and a fine. Motor vehicle drivers who commit any of the following violations will be penalized with a deduction of 3 points: 1. Driving a passenger vehicle (excluding buses) or school bus with more passengers than the approved number, but not exceeding 20%; 2. Driving a truck with cargo exceeding the approved load capacity, but not exceeding 30%; 3. Driving a medium-sized or larger passenger or cargo vehicle, or a hazardous materials transport vehicle on roads other than highways or urban expressways, or driving other motor vehicles at speeds exceeding the prescribed limit by less than 20%; 4. Driving a motor vehicle on a highway at a speed lower than the prescribed minimum speed limit; 5. Driving a motor vehicle prohibited from entering a highway onto a highway; 6. Driving a motor vehicle on a highway or urban expressway without using the designated lane; 7. Driving a motor vehicle through a crosswalk without slowing down, stopping, or yielding to pedestrians as required; 8. Driving a motor vehicle in violation of prohibition signs or markings; 9. Driving a motor vehicle without following the rules for overtaking, yielding, or driving in the opposite direction.
Was this review help?
11
0
Share
More Forum Discussions

What Causes Frequent Blowing of Automotive Fuses?

Below are the specific reasons for the frequent blowing of automotive fuses: 1. The fuse blows in the middle between two tightening screws. The fuse becomes thinner and blows as the tightening screws are tightened, usually due to the absence of washers or washers rotating with the screws. 2. Overloading. New electrical devices are added to the circuit, exceeding the safe current allowed by the fuse, or the fuse selected is too small. 3. Short circuit. A short circuit in the circuit or electrical device causes excessive current, leading to the fuse blowing. 4. The fuse blows at the root of the tightening screw. Loose or sparking tightening screws cause the fuse to blow; excessive tightening pressure flattens the fuse, reducing its current-carrying capacity and causing it to blow; loose wire terminal screws cause sparking when current passes, overheating the terminal plate and increasing the thermal load on the fuse, leading to blowing.
19
0
Share

What to Do If ETC Fails to Scan When Exiting the Highway?

If you find that the card was not scanned while traveling within the province, you need to promptly contact the toll station staff to have the card scanned and pay the fee to avoid affecting subsequent use. If the card was not scanned at an out-of-province highway exit, please consult the local ETC service hotline for specific handling procedures. How ETC Works: Through the onboard electronic tag installed on the vehicle's windshield, specialized short-range communication is established with the microwave antenna in the ETC lane at the toll station. This utilizes computer networking technology to perform backend settlement processing with the bank, thereby allowing vehicles to pass through highway or bridge toll stations without stopping while still paying the toll. Benefits of Installing ETC: Saves time by eliminating the hassle of waiting in line. Green and environmentally friendly, as vehicles pass through toll stations without stopping, reducing noise and exhaust emissions and minimizing pollution. Reduces wear and saves costs by decreasing the frequency of vehicle starts and stops, lowering wear and fuel consumption. Users also enjoy a 5% discount on toll fees. Improves efficiency, as ETC lanes can theoretically increase vehicle throughput by 2-3 times, making traditional ETC more updated, faster, and more high-tech. Compared to license plate payment, ETC technology is more mature and advantageous.
7
2
Share

How to Drive an Automatic Transmission Car for Better Fuel Efficiency?

Here are specific methods for driving an automatic transmission car to save fuel: 1. Utilize coasting. This does not mean coasting in neutral; do not shift to "N" while driving an automatic car. Instead, release the accelerator pedal to let the car coast using its momentum, which can save some fuel. 2. Start gently. Since the engine is cold and the water temperature is not yet at normal operating conditions, it consumes more fuel. After starting the car, let it warm up for about a minute. 3. Anticipate traffic lights. If you cannot pass through, release the accelerator early to control speed and avoid sudden braking, which can save over 30% of fuel.
7
2
Share

Do 4S shops charge labor fees for maintenance?

4S shops do not charge labor fees for the first maintenance. The following is a detailed introduction to car maintenance items: 1. Engine oil and oil filter replacement. This is mainly for the maintenance of the lubrication system. The main function of the lubrication system is to effectively lubricate various parts of the car engine to prevent excessive wear. The function of the oil filter is to remove various impurities from the engine oil to ensure the normal operation of the lubrication system. The oil filter should be replaced together with the engine oil during an oil change. Under normal circumstances, the car needs to be maintained every 5000KM. 2. The function of the air filter is to filter the air before it enters the cylinder, removing impurities, dust, sand, and other foreign objects. The cleaning and maintenance of the air filter depend on the usage environment. The gasoline filter is generally replaced after driving 20000-25000KM. 3. Spark plugs are consumable parts and should be replaced every 20000KM. In addition, components such as brake fluid, transmission oil, battery, throttle, fuel injector, and brake pads are all inspection items during routine maintenance, and maintenance should be carried out according to the usage conditions.
9
1
Share

What are the procedures for importing cars?

Here is a detailed introduction to the procedures for importing cars: 1. The import certificate of the goods, which is a receipt issued by the customs, is an important document for customs clearance. Without the import certificate, parallel imported cars cannot be registered. The content of the customs declaration can identify which car it is, and the place of production refers to the final production location, not the place of origin. 2. The inspection sheet for imported motor vehicles is a necessary procedure for registering parallel imported cars. Without the inspection sheet, parallel imported cars cannot be registered. 3. The vehicle conformity certificate. When the vehicle leaves the factory, the company attaches a vehicle conformity certificate stamped by the company and signed by the person in charge of vehicle conformity. 4. The purchase invoice. The invoice is necessary for purchasing the vehicle purchase tax when registering the car.
7
3
Share

How to Restore a Removed ETC Tag?

The anti-removal guide rod on the back of the ETC electronic tag is essentially a reset button switch. Once the button pops out, the information inside the ETC device is lost, and it needs to be reactivated by re-entering the information. You can try the ETC self-activation method. If that doesn't work, you will have to take it to an ETC service point or ETC service center to reactivate or cancel the ETC and replace it with a new ETC electronic tag. ETC Installation Process: Upon receiving the device, first check if the ETC card and electronic tag (OBU) are damaged. Press the anti-removal button on the back of the OBU. The red light will briefly turn on, and the OLED screen will display "Tag Invalid" or "Please Insert Card," indicating the device is functioning properly. Clean the front windshield, ensuring the surface is smooth, clean, and dry. Then peel off the adhesive backing of the OBU and stick it to the installation location. Press firmly for 2-3 minutes to remove any air bubbles. Insert the ETC card with the front side facing the driver and the back side facing the windshield, ensuring the chip is inserted into the OBU device. Benefits of Installing ETC: Saves time by eliminating the hassle of waiting in queues. Environmentally friendly—vehicles can pass through toll stations without stopping, reducing noise and exhaust emissions and minimizing pollution. Reduces wear and saves costs by decreasing the frequency of vehicle starts and stops, lowering wear and fuel consumption. Users also enjoy a 5% discount on toll fees. Improves efficiency—ETC lanes can theoretically increase vehicle throughput by 2-3 times, making traditional ETC faster, more advanced, and more high-tech. Compared to license plate payment, ETC technology is more mature and advantageous.
8
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.