···
Log in / Register

What is the normal tire pressure for sedans in summer and winter?

3 Answers
GavinLee
07/29/25 3:05pm
Normal tire pressure range in winter: In winter, the tire pressure should be based on the standard tire pressure of the car, with an appropriate increase of about 0.2bar. Normal tire pressure range in summer: Generally, the lower limit of the standard tire pressure of the car tire is sufficient. For example, the lower limit of standard tire pressure is 2.4bar. If the car is often parked outdoors, the tire pressure can generally be about 0.1bar lower than the standard to avoid tire blowouts due to high temperatures. According to the international GBT2978-2008 standard, the tire pressure for different tires is as follows: Standard tires: 2.4-2.5bar; Reinforced tires: 2.8-2.9bar; Maximum pressure: should not exceed 3.5bar. Tire pressure reset method: First, turn on the ignition switch, press and hold the tire pressure monitoring reset button, release it after hearing a "ding" sound, and the tire pressure monitoring system will store the current normal tire pressure data, automatically clear the original data, and finally the fault light on the dashboard will go out, and the tire pressure reset is completed.
Was this review help?
17
4
Share
JoannaLee
08/13/25 7:45am
I've been driving for over twenty years, and tire pressure is a big deal. Normal tire pressure is usually around 2.3 bar in summer and about 2.5 bar in winter due to significant temperature changes. In summer, higher thermal expansion means lowering the pressure a bit reduces the risk of blowouts. In winter, cold air causes contraction, so slightly higher pressure helps with smoother starts—safer and more reliable. I check the cold tire pressure weekly with a simple gauge, following the recommended values in the owner's manual. Don’t underestimate this—incorrect tire pressure leads to faster wear, reduced grip, and longer braking distances, increasing accident risks. Safety first! Making this a habit saves money in the long run, extends tire life, and keeps my car running smoothly.
Was this review help?
13
2
Share
Expand All
SanEden
10/11/25 6:25am
As a young commuter driver, tire pressure directly impacts fuel consumption and comfort. In summer, avoid setting tire pressure too high—2.2 to 2.4 bar is sufficient, as excessive expansion from high temperatures can increase fuel consumption. In winter, adjusting to 2.4 or 2.5 bar is better for quicker starts and improved fuel efficiency. From personal experience, proper tire pressure can save around 10% in fuel costs while making the seats feel softer and more comfortable. Remember to check tire pressure when the tires are cold, and adjust for the significant temperature differences between summer and winter. Regularly refer to the values on the door label—it's simple, practical, and helps prevent tire blowouts. A comfortable ride makes driving easier, and long-term fuel savings add up.
Was this review help?
5
3
Share
Expand All
More Forum Discussions

What type of engine oil is used for Buick Envision maintenance?

Buick Envision maintenance uses fully synthetic 5W30 engine oil. The detailed introduction of engine oil is as follows Engine oil grade: The grade includes two parts: classification and viscosity specification. The engine oil grade usually indicates viscosity and quality. The viscosity of lubricating oil is mostly identified by SAE grade; Functions of engine oil: The functions of engine oil include lubricating pistons and cylinders, assisting in cooling and heat dissipation, sealing to prevent leakage, and preventing excessive wear of parts. This requires the establishment of an oil film between two sliding surfaces. A sufficiently thick oil film separates the surfaces of relatively sliding parts, thereby achieving the goal of reducing wear; when the engine is working, the engine oil can bring heat back to the oil tank and then dissipate it into the air to help the water tank cool the engine. The real cooling effect comes from the water outside the engine shell; engine oil can form a sealing ring between the piston ring and the piston, reducing gas leakage and preventing external pollutants from entering; Precautions: When adding engine oil, the amount should be slightly lower than the standard scale. Excessive engine oil will increase the rotational resistance of the crankshaft, reduce the output power of the engine, and excess oil may enter the combustion chamber and participate in combustion, causing the vehicle to burn oil, emit blue smoke, and even increase fuel consumption.
1
5
Share

How to Check the Car Oil Dipstick?

To check the car oil dipstick, follow these steps: 1. The oil tank is generally located near the engine. Locate the oil dipstick on top of the oil tank. 2. The car must be parked on level ground with the engine off when pulling out the oil dipstick for measurement. 3. Pull out the dipstick. There is a textured area at the end with upper and lower lines. First, wipe the dipstick clean, then reinsert it and pull it out again. The oil level is acceptable as long as it falls between the upper and lower lines. If the oil level is above the upper line, it indicates too much oil; if it's below the lower line, it means there's insufficient oil.
14
4
Share

What is the code name for China V?

China V refers to the National Fifth Stage Emission Standard for Motor Vehicle Pollutants, which was issued on September 17, 2013, and officially implemented nationwide in 2017. As of 2019, China was still implementing the China V emission standard, but some cities began implementing the China VIa emission standard on July 1, 2020. Below is an introduction to automobile emission standards: Automobile emission standards regulate the content of harmful gases emitted from vehicle exhaust, such as CO (carbon monoxide), HC+NOx (hydrocarbons and nitrogen oxides), and PM (particulate matter, soot). These standards were first introduced in China in 2004. The implementation of automobile emission standards helps promote environmental protection and reduce pollution.
2
3
Share

How much engine oil does the Envision need?

Envision needs about 5 liters of engine oil. Precautions for adding engine oil: 1. When adding engine oil, just add it between the min and max marks. 2. After adding the engine oil, start the vehicle and check it 3 minutes after turning it off. Because the oil filter needs to be replaced when changing the engine oil, and the newly replaced oil filter does not contain oil. After starting the vehicle, the oil will flow into the oil filter. Turning off the engine for 3 minutes allows the oil to flow into the oil pan, making the oil level check more accurate. 3. Adding too much oil will affect the normal operation of the crankshaft and also increase the vehicle's fuel consumption, so the oil must be added within the specified range.
18
4
Share

How to Reset the Smart Maintenance Light?

Smart cars are wholly owned by Mercedes-Benz, established in 1994, and are a luxury brand among microcars. The vehicles are equipped with two types of engines: the first is a 0.9-liter turbocharged engine, and the second is a 1.0-liter naturally aspirated engine, along with a very distinctive soft-top convertible. The method to reset the Smart maintenance light is as follows: 1. Turn on the vehicle's power; 2. Use the left multifunction button to locate the vehicle's maintenance information; 3. Open the vehicle's mileage data and hold the OK button for 20 seconds; 4. After the dashboard maintenance information starts flashing, press and hold the RES button; 5. The vehicle's maintenance light will be reset.
19
4
Share

How to Replace the Battery in a Levin Car Key?

Levin is a 'New Sensory Leading Compact Sedan' based on Toyota's MC platform, specially and deeply customized for Chinese consumers. The following are the specific steps to replace the battery in a Levin car key: 1. First, remove the mechanical key. Use a screwdriver to gently pry at the spot where the mechanical key is taken out, then open the back cover. Avoid getting the circuit board wet and try not to touch it, as moisture or contact may damage the circuit board. 2. Next, replace it with a new button battery of the same model, ensuring the '+' positive side is facing upwards during installation to complete the process.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.