What is the normal tire pressure for Geely Emgrand GS?

1 Answers
LeValerie
07/30/25 9:38am
The recommended tire pressure range for Geely Emgrand GS is 2.4-2.5 bar. Due to seasonal factors, the normal tire pressure may vary slightly between different models. In winter, the tire pressure can be appropriately increased by 0.2 bar, while in summer it can be reduced by 0.1 bar. This data complies with the international GBT2978-2008 standard. The Geely Emgrand GS comes equipped with a tire pressure monitoring system that automatically alerts the driver without manual operation. The Emgrand GS tire pressure monitoring system does not have a digital display. The tire pressure warning light will only illuminate when the tire pressure is too low (below 1.8 bar) or too high (above 2.8 bar). If the warning light is off, it indicates normal tire pressure. Generally speaking, a tire pressure above 2.8 bar is considered too high, while a tire pressure below 2.0 bar is considered too low. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; Causes steering wheel vibration and deviation, reducing driving comfort; Accelerates wear on the central tread pattern, shortening tire lifespan; Increases vehicle vibration, indirectly affecting the lifespan of other components; Overextends tire cords, reducing tire elasticity and increasing the load on the vehicle during driving. Hazards of insufficient tire pressure: Increases friction coefficient with the road surface, leading to higher fuel consumption; Makes the steering wheel heavy and prone to deviation, compromising driving safety; Increases movement of tire components, causing abnormal heat due to excessive rolling; Weakens cord and rubber functions, leading to delamination or cord breakage and excessive friction with the rim, damaging the bead area and causing abnormal wear; Multiplies friction between the tire and the ground, sharply increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may result in a tire blowout. If the tire pressure monitoring indicator light illuminates (a yellow symbol with an irregular circle, no stamp on top, four small spikes at the bottom, and an exclamation mark inside), it is generally due to one of the following three reasons: Abnormal tire pressure: The system typically alerts when the pressure is below 1.8 bar or above 3.0 bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset promptly, the system may still record the previous data, causing the indicator light to illuminate. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, installed inside the tire and connected to the inflation valve, monitors tire pressure. If the sensor is damaged due to impact while driving, the tire pressure warning light will illuminate. In such cases, the only solution is to replace the sensor with a new one.
Was this review help?
3
4
Share
More Forum Discussions

How to Set Up the Anti-Pinch Function for Lexus ES Windows?

Lexus ES window anti-pinch function is enabled by default, so no setup is required. The anti-pinch function is a comfort feature where the electric window glass will automatically stop or reverse its upward motion when encountering slight resistance during closing, preventing injuries. Below are the steps to reset the anti-pinch function: 1. Press and hold the window up button to manually raise the window to its highest point. 2. Release the up button. 3. Press and hold the up button again for 3-5 seconds, then release to restore the one-touch anti-pinch function. The anti-pinch feature for electric windows is a comfort configuration where the glass automatically stops or reverses direction upon encountering minor resistance during closing, thus preventing injuries to body parts (e.g., hands, head, etc.).
20
4
Share

Is the new Sylphy fuel-efficient?

The MIIT comprehensive fuel consumption report for the new Sylphy is 5.2-6.7L/100km. In actual usage, a fluctuation of up to 10% is considered normal. The following four factors can affect fuel consumption: 1. Driving habits of the owner can influence fuel consumption. For example, driving with the air conditioning on will consume more fuel than without it; 2. Although the Sylphy's load capacity isn't high, this factor still affects its fuel consumption. The impact might not be noticeable over short distances, but over 100 kilometers, it can be significant. Generally, driving alone for 100 kilometers will use about 0.5 liters less fuel than driving with a full car; 3. Different road conditions lead to varying engine power losses, which naturally results in differences in fuel consumption. Generally, smoother roads lead to lower fuel consumption; 4. If the engine is not properly maintained after a period of driving, fuel consumption may increase.
17
2
Share

How Long Does BMW Remote Upgrade Take?

BMW remote upgrade takes about 20 minutes. During the upgrade, the mirrors cannot be automatically folded when locking the car. System upgrade means programming the vehicle, and the modules that need programming cannot be manually selected. Introduction to BMW Cars: BMW cars refer to vehicles produced by Bayerische Motoren Werke AG (abbreviated as BMW). The main series models include the 1, 2, 3, 4, 5, 6, 7, and 8 series. BMW Car Logo: The logo features a double-circle design with the "BMW" lettering above the double rings. The entire emblem resembles the blue sky, white clouds, and a continuously rotating propeller, symbolizing BMW's long history and the company's consistent purpose and goals.
18
5
Share

Which country is the Lexus sedan brand from?

Lexus sedans are a Japanese brand, and Lexus is under the Toyota Motor Corporation brand, with its headquarters located in Tokyo, Japan. Lexus offers models such as the Lexus ES, Lexus RX, Lexus LS, Lexus CT, and Lexus LX. Taking the Lexus ES as an example, its body dimensions are 4975mm in length, 1866mm in width, and 1447mm in height, with a wheelbase of 2870mm. In terms of power, the Lexus ES gasoline version comes with two engine options: a 2.0L and a 2.5L, with maximum output power of 173 horsepower and 207 horsepower respectively, and peak torque of 208 Nm and 243 Nm respectively. The transmission is matched with a CVT and an 8AT gearbox, with fuel economy and smoothness being its highlights.
9
5
Share

How to Turn Off the Auto Hold Function in Audi A4?

The Auto Hold function in the Audi A4 has a dedicated button for turning it on and off, which is the 'A' button located behind the electronic parking brake. To use it, press the 'A' button first, and when the indicator light turns on, the system will officially enter standby mode. The following are the prerequisites for using the Auto Hold function: 1. The engine must be running; 2. The car doors must be closed; 3. Another important point is that the driver must fasten the seat belt. Below is some relevant information about the Auto Hold function: Audi's Auto Hold function is also known as the Audi Vehicle Hold Assist System. Its main role is to automatically determine the vehicle's specific state and pre-tension the electronic parking brake to achieve the parking effect.
13
0
Share

What engine does the Refine use?

The Refine is equipped with an engine model HFC4GA1-C. Specific details are as follows: 1. The Refine's 2.0T engine delivers relatively smooth power output during acceleration. It requires 2,500 revolutions to feel the burst of power, accompanied by a rise in engine sound. Although the thrust isn't particularly pronounced, the working state of the turbocharger can still be sensed. 2. This engine utilizes new materials such as an aluminum alloy cylinder block, plastic intake manifold, stainless steel exhaust manifold, plastic cylinder head cover, and aluminum alloy timing chain cover. It incorporates advanced technologies including variable valve timing (VVT), double overhead camshafts, 16 valves, timing chain drive, and an integrated oil pump. 3. Additionally, it employs new processes like fractured connecting rods and friction welding for the plastic intake manifold, effectively enhancing the engine's power and fuel efficiency while reducing emissions and noise.
3
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.