What is the normal temperature range for antifreeze?

1 Answers
DeLila
07/30/25 2:35am
Antifreeze's key indicators are its freezing point and boiling point. In the market, antifreeze is available with freezing points of -15°C, -25°C, -30°C, -40°C, etc. Generally, it's advisable to choose an antifreeze with a freezing point at least 10°C lower than the lowest temperature in your region. Antifreeze replacement method: Before completely replacing the antifreeze, conduct a thorough inspection to check for any leaks or cracks in the pipes, with a focus on the five-way hose. The five-way hose is named for its five connection points to various parts. Antifreeze flows through the five-way hose and is distributed to different parts of the car to function. If there are signs of antifreeze leakage in this part, replace the hose or resecure the connection as needed. Drain the old antifreeze, then flush the liquid channels with clean water. Add clean water to the antifreeze reservoir, then continue filling the reservoir with water to allow it to circulate continuously through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. The water initially draining from the reservoir will have a faint pink tint. Keep adding clean water until the drained water runs clear. Note: Remember to remove the heater hose and drain the water from the heater core. After draining for about an hour, add the new antifreeze through the radiator hose, which allows the antifreeze to flow quickly into the radiator. Then add another bottle of antifreeze to the reservoir until it's nearly full. Start the engine and let it run for about 10 minutes. During this time, the coolant level will drop slightly as air is purged from the system. Top up the antifreeze to the "MAX" mark on the reservoir.
Was this review help?
5
1
Share
More Forum Discussions

Which company's motors does Tesla use?

Tesla uses motors that are independently designed and developed, and Tesla's motors are produced in Nevada, USA. Tesla is an automobile manufacturer from Silicon Valley, USA, and its models include the Model 3, Model S, Model X, Model Y, etc. Relevant details are as follows: 1. Body dimensions: The Model 3 is Tesla's entry-level model, a pure electric mid-size sedan. The Model 3 has a wheelbase of 2875 mm, with length, width, and height measuring 4694 mm, 1850 mm, and 1443 mm, respectively. The Model 3 is available in both rear-wheel-drive and all-wheel-drive versions, with the all-wheel-drive version featuring dual motors. 2. Power: The rear-wheel-drive version has a motor with a maximum power of 202 kW and a maximum torque of 375 Nm. The all-wheel-drive version's dual motors have a combined power of 340 kW and a total torque of 639 Nm. The Model 3 uses ternary lithium batteries across the entire lineup, which are lighter in weight and have higher energy density.
16
1
Share

How many months of production time qualifies a new car as inventory stock?

New cars stored in warehouses for more than half a year are generally considered inventory stock. There is no strict definition for inventory vehicles, nor are there any national regulations specifying the term. However, the automotive sales industry does recognize the concept of inventory cars. For imported vehicles, due to factors like transportation cycles, those manufactured six months to a year or more ago are also classified as inventory stock. Disadvantages of inventory vehicles: Long-term stationary storage can lead to moisture damage in electronic components due to lack of power, resulting in oxidation and corrosion. When these components are eventually used, they may malfunction or fail to operate properly. The longer a vehicle remains idle, the greater the impact on its electronic parts. Fluids such as engine oil and brake fluid degrade over time, as oxidation from exposure to air reduces their performance effectiveness. Maintenance for inventory vehicles: First, assess the exterior paint's gloss to determine if repainting or polishing is needed. Next, maintain rubber components, which naturally deteriorate with age. Upon receiving the vehicle, owners should have these parts inspected and replaced if necessary. Finally, check electronic devices and wiring inside the car, including all buttons. Additionally, inspect the fuel tank for sediment buildup and ensure the fuel injectors are functioning correctly.
19
3
Share

Where is the location of the car's drainage holes?

Generally, the drainage holes of a vehicle are located in the following areas: the front windshield of the engine compartment, the four corners inside the sunroof, the lower part of the front and rear doors, inside the fuel tank cap, at the bottom of the spare tire in the trunk, and the gaps between the front and rear headlights and the body fenders. The most prone to clogging are the drainage holes in the engine compartment and the sunroof. The drainage outlets on a car are as follows: 1. Radiator drainage hole: Most radiators tilt upwards, so they may contain a lot of water. For safety, a drainage pipe is designed to drain water using a special conduit. If driving for too long, dirt may accumulate on it, requiring cleaning to prevent vehicle corrosion. 2. Door drainage outlet: This drainage outlet is located within the door's rubber seal, providing a certain level of sound insulation. If water enters the door, it could potentially damage the electronic components inside. 3. Sunroof drainage outlets: Sunroofs usually have several drainage outlets to prevent water accumulation from rain from seeping into the car. 4. Car condensate drainage outlet: The car condensate drainage outlet is typically located under the car's evaporator. Normally, if a puddle of water is found under the car, it indicates an issue with the condensate drainage outlet.
19
5
Share

Can a smart car go on the highway?

smart cars can go on the highway. The specific details are as follows: 1. Power: The Mercedes-Benz smart is equipped with a three-cylinder engine, delivering a maximum power of 109 horsepower (80 kW) and a maximum torque of 170 Nm. The official data states a top speed of 155 km/h. Although there are no issues with going on the highway if all documents are complete, due to its lightweight and small size, it is not recommended to drive this car at high speeds on the highway as it can easily become unstable. Even if driving on the highway is unavoidable, it is advised to keep the speed below 100 km/h. 2. Body dimensions: The dimensions are 2695 mm in length, 1663 mm in width, and 1542 mm in height, with a wheelbase of only 1873 mm. It is positioned as a micro commuter car, and there is also a convertible version available for consumers. However, there have been real cases where, after going on the highway, the panoramic roof suddenly blew off, nearly hitting a small Polo behind it. This can be considered a global first and is an important reason why it is not recommended to drive a smart car on the highway.
5
0
Share

How to Reset the Maintenance Light on a Corolla 1.2t?

Steps to reset the maintenance light on a Corolla 1.2t: 1. Press the Corolla's one-touch start button to ignite and start the vehicle; 2. Press the trip meter reset button to switch to trip meter A; 3. Turn off the engine switch; 4. While pressing the trip meter reset button, switch the engine to ON mode, and hold the button until the trip meter displays 000000. The maintenance light will then be reset. The Corolla 1.2t has a maximum power output of 116 horsepower, a maximum torque of 185 Nm, and a top speed of 180 km/h.
11
3
Share

Does Water Entering the Exhaust Pipe Affect the Car?

Water entering the exhaust pipe can affect the car. Here are the detailed impacts: 1. It can cause serious consequences such as water entering the engine: If only the exhaust pipe has water, the accumulated water should be removed as soon as possible to prevent impurities in the water from clogging the three-way catalytic converter or damaging the oxygen sensor. 2. It may lead to exhaust pipe blockage: Poor exhaust can cause the engine to stall, but the engine may not necessarily take in water at this time. 3. Piston damage: Since water is far less compressible than oil, if a certain amount of water enters the cylinder under high pressure, it can easily break the engine's connecting rod or even damage the piston.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.