What is the ground clearance of the Changan Eado?

1 Answers
LaGianna
07/29/25 3:32pm
The ground clearance of the Changan Eado is 160mm. Below is some knowledge about ground clearance. Ground clearance varies by vehicle type: For sedans, the ground clearance ranges between 110 to 150 millimeters; for SUVs, it ranges between 200 to 250 millimeters; for sports cars, it is below 100 millimeters. Function of ground clearance: Ground clearance determines a vehicle's ability to pass obstacles. It refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the vehicle is fully loaded and stationary. It is used to characterize the vehicle's ability to pass over obstacles like rocks and tree stumps without collision. The greater the ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven terrain, but the higher the center of gravity, which reduces stability. The smaller the ground clearance, the weaker the vehicle's ability to pass over obstacles or uneven terrain, but the lower the center of gravity, which increases stability.
Was this review help?
4
4
Share
More Forum Discussions

What are the reasons for the ABS warning light to illuminate in a Citroen C-Quatre?

The reasons for the ABS warning light to illuminate in a Citroen C-Quatre are: 1. When the vehicle speed exceeds 10 km/h, no rotation speed signal is transmitted to the ABS control unit; 2. When the vehicle speed exceeds 40 km/h, the rotation speed signal exceeds the tolerance value; 3. There is a recognizable open circuit or short circuit to the positive or ground in the sensor. The Citroen C-Quatre is a compact car launched by Dongfeng Citroen, with a length, width, and height of 4588mm, 1800mm, and 1496mm respectively, a wheelbase of 2610mm, equipped with a 1.6L naturally aspirated engine and a 1.2T turbocharged engine, with maximum power outputs of 86kw and 100kw respectively, matched with a 5-speed manual or 6-speed automatic transmission.
3
1
Share

Where is the cabin air filter of the JINGYI X3 located?

The cabin air filter of the JINGYI X3 is located in the engine compartment, directly above the engine and below the wipers. There is a black cover plate, and the filter can be seen after removing the cover. Below is some relevant information: 1. The JINGYI X3 is an SUV strategic model launched by Dongfeng Fengxing Automobile for young first-time buyers. It is the first extra-large urban wide-comfort SUV in China. 2. A dirty cabin air filter can lead to reduced cooling efficiency of the air conditioning, decreased airflow from the vents, and most importantly, it can affect the air quality inside the vehicle, impacting the health of the driver and passengers. 3. If the airflow from the air conditioning significantly decreases, the cabin air filter may be clogged. The filter should first be cleaned or replaced if necessary. The frequency of cleaning depends on road conditions (such as dusty roads, etc.), and it is recommended to clean it earlier rather than later.
19
5
Share

Where is the cabin air filter located in the Mercedes-Benz E300?

The Mercedes-Benz E300 has two cabin air filters. One is located inside the glove compartment in front of the front passenger seat, and the other is positioned behind the right front shock absorber mount in the engine compartment. The Mercedes-Benz E300 is a mid-range vehicle from Mercedes-Benz, equipped with a 2.0T inline 4-cylinder turbocharged engine delivering a maximum power of 190 kW and a peak torque of 370 Nm, paired with a 9-speed automatic transmission. In terms of dimensions, the Mercedes-Benz E300 measures 5078mm in length, 1860mm in width, and 1484mm in height, with a wheelbase of 3079mm. The vehicle features a multi-link independent suspension at both the front and rear. For safety, the Mercedes-Benz E300 comes with a 360-degree panoramic camera, cruise control, and ACC adaptive cruise control.
12
0
Share

How to Open the Hood of a Ford New Focus?

Here are the steps to open the hood: 1. In most sedans, the hood release lever is located under the dashboard near the driver's left calf, facing the front of the car. Pulling this lever will cause the hood to pop up about 1cm. Then, while lifting the hood with one hand, use the other hand to reach inside the upper part of the grille to find the hood latch. The position of the latch is generally similar across different car models, but the direction of operation may vary. 2. After sitting in the driver's seat, locate the release lever near your left leg and pull it to slightly lift the hood. Then, move to the front of the car, facing the Focus. On the left side, through the gap, you will see a yellow lever. Pull it again to fully lift the hood. There is a yellow rod; lift it and hook the small end into the hole on the hood. 3. When closing the hood, do not press it down. Lift the hood to about three hand-widths above the closed position and let it close by its own weight.
7
1
Share

How to Clean Brake Dust on Wheel Hubs

Methods for cleaning brake dust on wheel hubs are introduced as follows: 1. You can use a wheel hub cleaner and a soft brush to scrub. Avoid using overly hard brushes or wire brushes to prevent scratching the rim surface. 2. Use high-pressure water to rinse off mud and dust from the tire, the exterior of the rim, and the inner side of the fender, then wipe with a towel to remove any loose dirt. For cleaning the rim, evenly spray an aluminum alloy rim cleaner on the surface, wait for 2-3 minutes, and then use a soft brush or sponge to wipe, being careful not to damage the metal surface. Also, ensure no areas are missed between the blades and spokes of the rim. 3. When cleaning aluminum alloy rims, since their surfaces have a protective coating, use a neutral cleaner. Avoid alkaline cleaning solutions, corrosive solvents, fuel, or strong cleaners, as these can damage the protective layer. Additionally, use soft items like sponges to gently scrub to avoid damaging the glossy layer of the paint film. Clean one rim at a time to prevent the cleaner from drying on the surface. Do not clean the rim when it is at a high temperature.
1
2
Share

How to use the auto start-stop function in Audi Q3?

The start-stop function button in Audi Q3 is located below the center console. When the start-stop button indicator light is on, it indicates the function is turned off. The start-stop system must be manually deactivated after each engine start. This function cannot be permanently disabled and can only be manually turned off after each startup. Below is relevant information: 1. The engine start-stop technology automatically shuts off the engine when the vehicle comes to a temporary stop during driving (such as waiting at a red light). When it's time to move forward again, the system automatically restarts the engine. 2. The working principle of the start-stop system is that when the vehicle stops moving due to traffic congestion or at an intersection, and the driver presses the brake pedal and shifts to neutral, the Start/Stop system automatically checks: the engine is idling and in neutral; the wheel speed sensors of the anti-lock system show zero; the electronic battery sensor indicates sufficient energy for the next start. When these three conditions are met, the engine automatically stops. 3. The Audi Q3 is positioned as a compact SUV, with excellent overall quality and reputation, as well as great cost performance, being a top-tier luxury brand after all.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.