What is the gap size of a car spark plug?

1 Answers
Ann
07/29/25 5:15pm
The normal gap of a spark plug is generally 0.6~1.3 millimeters. Spark plug replacement procedure: Open the hood, lift the plastic cover of the engine, remove the high-voltage distributor wires, and mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for external debris like leaves or dust and ensure thorough cleaning. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage distributor wires in the firing order, then secure the cover. Spark plug replacement interval: Under normal maintenance conditions, replace spark plugs every 40,000~60,000 kilometers. However, this may vary depending on the brand and engine type, so it's recommended to follow the owner's manual. Platinum spark plugs should be replaced at 40,000 km, standard nickel alloy spark plugs at 20,000 km, and iridium spark plugs at 60,000-80,000 km.
Was this review help?
20
4
Share
More Forum Discussions

How to Turn Off the ECO Indicator Light in a Car?

Method to turn off the ECO indicator light in a car: When the ECO mode is on, press the ECO button again to turn off the indicator light and deactivate the ECO function. Location of the ECO button: The ECO button is usually located on the left side of the car, marked with the letters "ECO". Some models have a green button, making it easy to identify. Principle of ECO: ECO primarily works by comprehensively analyzing and judging various factors that affect fuel consumption during vehicle movement, such as automatic transmission gear, engine speed, vehicle speed, braking, and transmission oil temperature. The ECU control unit calculates the optimal fuel amount to provide to the engine, effectively reducing fuel consumption compared to normal driving mode. Simply put, it controls the engine speed with appropriate gear shifts to minimize unnecessary fuel consumption.
10
4
Share

What to Do When the Enclave Runs Out of Battery?

Methods for dealing with a dead battery in the Enclave: 1. Remove the battery, charge it, and then attempt to start the vehicle. 2. If the battery is too depleted to start the car, you can call for free jump-start service from after-sales support or request assistance from a repair shop. 3. It is recommended that the owner wait for rescue services from a 4S shop. Below is relevant information about the Enclave: The Buick Enclave is equipped with various navigation methods, OnStar All-Time Online Assistant, ACC adaptive cruise control system, LKA lane keeping system, SBZA side blind zone alert system, APA automatic parking system, intelligent headlight system, FDI front vehicle distance alert, FCA forward collision alert system + CMB collision mitigation system, RCTA parking alert system, and more.
16
0
Share

The Function of the Cooling System?

The functions of the cooling system are as follows: 1. To keep the engine within an appropriate temperature range under all operating conditions. 2. The cooling system must prevent the engine from overheating as well as from becoming too cold during winter. Additional information about the cooling system is as follows: 1. Depending on the cooling medium, cooling systems can be categorized into air-cooled and water-cooled systems. 2. In the electromechanical equipment industry, the cooling system is an extremely critical component. It is vital for the safe operation and service life of the cooled electromechanical devices, yet it is often overlooked and remains a weak link. 3. The primary function of the cooling system is to dissipate the heat generated by engine combustion.
17
3
Share

How to Remove the Fog Lights on a BMW 5 Series?

BMW 5 Series fog light removal method: 1. There is a small cover below the fog light. Remove the cover to reveal a cross-head screw inside. Use a long-handled cross-head screwdriver to remove it, and the fog light can then be taken out. 2. When removing the fog light cover, pry it from the inside outward. Apply slight force to open each clip one by one. A flat-head screwdriver will suffice, and to prevent scratching the car paint, you can wrap the tip with a thin cloth. Below is some related information about BMW 5 Series fog lights: 1. If replacing the fog light, simply unplug the connector—it's that easy. 2. One thing to note: when reinstalling the fog light cover, first install the outer side, then the lower side snug against the daytime running light, and finally the inner upper side. Otherwise, it won't fit properly.
4
4
Share

What is the maximum displacement of the Honda Avancier?

The maximum displacement of the Honda Avancier is 2.0L. Below is more information about the Honda Avancier: 1. The Avancier is equipped with a matte leather seat system, which is the first in Honda models to feature rapid heating and ventilation for the front seats, as well as a 12-way power adjustment for the driver's seat. 2. The Avancier comes with two powertrain options: a 1.5T and a 2.0T. The mid-to-low trim models are equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 193Ps, maximum power of 142kW, peak torque of 243N·m, and paired with a CVT continuously variable transmission. The high-end models feature a 2.0T direct-injection VTEC turbocharged engine, producing a maximum horsepower of 272Ps, maximum power of 200kW, peak torque of 370N·m, and mated to a 9-speed automatic transmission.
8
5
Share

What Causes a Motorcycle to Stall When Starting in First Gear?

Motorcycle stalling when starting in first gear can be attributed to the following reasons: Motorcycle with stand: For motorcycles equipped with a side stand safety switch, the engine will stall if the gear is engaged while the stand is deployed. This safety feature prevents the rider from forgetting to retract the stand and attempting to ride with it still extended. Clutch not fully engaged: If the motorcycle starts normally in neutral but stalls immediately when shifted into gear, it indicates the clutch isn't fully disengaged. At idle speed's low RPM, the engine can't compensate for the vehicle's mass before stalling occurs. Poor quality engine oil: Another scenario involves using low-grade oil during summer, especially if the motorcycle remains unused for six months. When attempting to ride in winter, the engine may start but stall upon gear engagement. This occurs because inferior oil becomes excessively viscous in cold temperatures, preventing proper clutch disengagement.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.