What is the fuel tank capacity of the Great Wall H3 in liters?

2 Answers
StRicardo
07/29/25 10:08am
74 liters, with the same tank size across all configurations. Below is relevant information about the Great Wall H3: 1. Great Wall H3: The Great Wall H3 shares the same platform as the Haval, inheriting the Haval's reliable quality while offering the comfort of a sedan and the practicality of a multi-purpose vehicle. 2. Fuel tank capacity: The fuel tank capacity varies by model, and even among vehicles of the same class from different brands, as there is no national standard. However, most automakers follow a general principle where a full tank typically supports a driving range of around 600 kilometers, not less than 500 kilometers.
Was this review help?
1
4
Share
DiSadie
08/13/25 1:07pm
I remember when I drove the Great Wall H3 years ago, its fuel tank was 72 liters, which is quite large for an SUV. A full tank could take me quite far. On highways, my average fuel consumption was around 10 liters per 100 kilometers, so one tank could cover about 700 kilometers, making it great for long trips. In city driving, the fuel consumption might be higher, but the 72-liter capacity meant fewer trips to the gas station, saving a lot of time. Drivers should be careful not to wait until the fuel light comes on to refuel, as this can overheat and damage the fuel pump, affecting engine longevity. During maintenance, I also checked the fuel tank's sealing, especially since older cars' rubber gaskets can degrade and cause leaks. Overall, the 72-liter design balances practicality and economy.
Was this review help?
2
5
Share
Expand All
More Forum Discussions

How to Calibrate the Senova X35 SAS?

Select the X35 model, click "Start Diagnosis", and load the program. Double-click "Electric Power Steering (EPS)" to enter the diagnostic interface. Select "ECU Configuration" and click "Steering Angle Sensor Calibration". Click "Calibrate" to complete the calibration.
9
3
Share

How to remove the small wrench icon on the 2014 B50 dashboard?

Insert the key, but only insert it without turning. Hold the lever next to the odometer for 5-10 seconds, then turn the key to power on. After another 5-10 seconds, start the car. Keep holding the lever throughout this process without releasing it. Generally, following these steps will clear the small wrench icon. If it doesn't clear, repeat the same process a few more times.
9
0
Share

What Causes High Transmission Temperature?

Reasons for high transmission temperature: 1. Clogged pump suction filter screen; 2. Poor radiator cooling capacity; 3. Severe machine overload operation; 4. Serious wear or damage to the transmission hydraulic pump; 5. Severe system leakage, improper operation of the torque converter inlet regulating proportional valve; 6. Transmission clutch slippage can also lead to excessively high transmission temperature. The transmission is a mechanism used to change the speed and torque from the engine, capable of fixing or changing the gear ratio between the output and input shafts, also known as a gearbox. The transmission consists of a gear transmission mechanism and a control mechanism, with some vehicles also equipped with a power take-off mechanism.
16
2
Share

Can the car still be driven if the transmission is slipping?

If the transmission is slipping, the car should not be driven as it poses a safety hazard and requires immediate repair. Causes of transmission slipping: 1. Wear and tear of the clutch, brake, or one-way clutch leading to slipping; 2. Addition or replacement with non-specified oil; 3. Slipping caused by low main oil pressure. The transmission mainly refers to the car's gearbox, which is divided into manual and automatic types. Manual transmissions primarily consist of gears and shafts, achieving speed and torque variation through different gear combinations; automatic transmissions are composed of a torque converter, planetary gears, a hydraulic torque variation system, and a hydraulic control system, achieving speed and torque variation through hydraulic transmission and gear combinations.
11
2
Share

What is the valve clearance for the Ford Focus?

Ford Focus valve clearance is 0.22 to 0.28MM for intake and 0.27 to 0.330MM for exhaust when the engine is cold. Valve clearance is set to ensure the proper operation of the internal combustion engine's valve train. Since the valve train operates at high speeds and elevated temperatures, components like the valve tappet and valve stem expand when heated. Without proper clearance, this expansion could automatically push the valve open, preventing it from sealing tightly against the valve seat, leading to air leakage. The Focus is an A-segment family car and one of Ford Europe's flagship models. It is equipped with either a 1.5L EcoBoost or a 1.5L Ti-VCT engine, and all models meet the China VI emission standards.
16
2
Share

How Should Beginners Drive on the Highway?

Beginners on the highway should maintain a safe distance from the vehicle in front. Here are some tips for beginners driving on the highway: 1. High-speed driving: Avoid sudden steering wheel movements while driving on the highway. Do not reverse, drive against traffic, or make U-turns or turns across the central divider. During normal driving, the following vehicle in the same lane must maintain a sufficient distance from the vehicle in front. 2. Precautions: When entering the highway, accelerate to a speed of at least 50 km/h as quickly as possible. Vehicles entering the highway from the ramp must increase their speed in the acceleration lane. When merging into the main lane, they must not hinder vehicles already traveling in the main lane and should drive in the outer lane.
14
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.