···
Log in / Register

What is the fuel consumption of the Hongqi HS7?

5 Answers
VonChristopher
07/25/25 7:24am

The fuel consumption of the Hongqi HS7 with a 2.0T engine is 8.6L per 100 kilometers, while the 3.0T engine consumes 10.9L per 100 kilometers. These figures are based on official data. The Hongqi HS7 requires the use of 95-octane fuel. The Hongqi HS7's fuel consumption varies depending on the engine model. The distance it can travel on a full tank of fuel is as follows: For models equipped with a 252-horsepower engine, the fuel tank capacity is 75L, and the distance it can travel on a full tank is 75/8.6100=872km. For models equipped with a 337-horsepower engine, the fuel tank capacity is 75L, and the distance it can travel on a full tank is 75/10.9100=688km. Factors affecting a car's fuel consumption: Tires: If the tire pressure is insufficient, fuel consumption will increase. If the tire pressure is normal, check the wear level of the tires. Severe tire wear can lead to frequent slipping, which increases fuel consumption. Engine: A buildup of carbon deposits in the engine over a short period can also result in higher fuel consumption. This may be caused by using substandard fuel. The solution is to add a certain amount of cleaning agent when refueling. If the effect is not noticeable, it indicates a significant buildup of carbon deposits in the engine. In such cases, it is advisable to visit a 4S shop or repair shop for a professional cleaning of the engine's carbon deposits. Oxygen Sensor: As an internal control unit in the car, the oxygen sensor monitors the air-fuel ratio of the engine. If it is damaged, it will disrupt the air-fuel ratio, leading to abnormally high fuel consumption. A damaged oxygen sensor will cause the exhaust pipe to emit dark-colored exhaust gases while driving, necessitating prompt replacement. Control Unit: If one of the engine's control units malfunctions, it may result in increased fuel consumption, accompanied by poor performance and dark exhaust emissions.

Was this review help?
4
3
Share
JaxonMarie
08/11/25 1:27pm

I've been driving the Hongqi HS7 for a while now, and I feel the fuel consumption is generally manageable, with an average combined fuel economy of about 10 to 11 liters per 100 kilometers. It really depends on road conditions: in city traffic jams, it can jump to 13 liters, while on smooth highways, it drops to just over 8 liters. There are quite a few influencing factors, such as higher fuel consumption when using air conditioning in summer or slightly increased consumption in cold winter temperatures. Driving habits also play a role—sudden acceleration or hard braking consumes a lot of fuel, so I usually maintain a steady speed and try to avoid frequent lane changes. Regular maintenance also affects fuel efficiency; underinflated tires or poorly changed engine oil can increase consumption, so I always keep up with scheduled checks. Overall, while this car isn’t the most fuel-efficient, it offers strong performance, making it a good value for the price.

Was this review help?
13
4
Share
Expand All
Elmer
09/27/25 6:09am

As someone who is mindful of expenses, I pay close attention to the fuel consumption of the Hongqi HS7, which averages around 11 liters per 100 kilometers. In city driving, it easily exceeds 12 liters, but on highways, it can drop below 9 liters. To save money, I've developed some good habits: for example, planning routes in advance to avoid congestion and minimizing overtaking to maintain smooth driving, which can keep fuel consumption under 10 liters. In terms of maintenance, regular oil changes and cleaning the throttle body can improve fuel efficiency; keeping tires properly inflated or adding fuel additives also helps a little. Additionally, heavy loads or more passengers increase fuel consumption, so I try to carry less unnecessary weight. Based on actual tests, fuel consumption is manageable, and daily maintenance should not be overlooked.

Was this review help?
5
1
Share
Expand All
Robyn
11/10/25 8:09am

The Hongqi HS7 is equipped with either a 2.0T or 3.0T engine, with varying fuel consumption. Generally, the 2.0T engine has a combined fuel consumption of about 10.5 liters per 100 kilometers, with approximately 12 liters in urban areas and over 8 liters on highways. The 3.0T engine has slightly higher consumption, around 12 liters combined, with 14 liters in urban areas and 10 liters on highways. This depends on factors such as the drivetrain, vehicle weight, and temperature—for instance, fuel consumption tends to be higher in extreme heat or cold. Driving habits also play a key role; avoiding sudden acceleration and using cruise control more often can save fuel. During maintenance, keeping the air filter clean helps optimize efficiency.

Was this review help?
8
0
Share
Expand All
GabrielMarie
01/01/26 3:06am

As a new owner of the Hongqi HS7, I was relieved by its fuel consumption. The combined average hovers around 10 liters with minimal fluctuation. On highways, it easily drops to just over 8 liters, while in urban areas it rises to 12 liters, which is still acceptable. Factors like air conditioning use may slightly increase consumption, but the design is quite optimized. Pay attention to speed - the most economical range is between 60-80 km/h. Regular vehicle checks help maintain stable fuel efficiency.

Was this review help?
3
5
Share
Expand All
More Forum Discussions

how to fix thermostat in car

Fixing a car thermostat is a moderate-difficulty DIY task that involves draining the coolant, removing the old thermostat, and installing a new one with a fresh gasket. The core of the job is straightforward, but safe access to the thermostat housing is often the biggest challenge. If you're not comfortable working with hot coolant or have a tightly packed engine bay, it's often wiser to hire a professional. The thermostat is a temperature-controlled valve, usually located where the top radiator hose meets the engine. Its job is to block coolant flow to the radiator until the engine warms up, helping it reach optimal operating temperature quickly. Step-by-Step Guide: Safety First & Cool Down: Never open the cooling system on a hot engine. The system is pressurized, and scalding hot coolant can erupt violently. Let the car sit for several hours or overnight to cool completely. Drain the Coolant: Place a drain pan underneath the radiator. Open the radiator drain petcock or loosen the lower radiator hose to capture the old coolant. You may not need to drain all of it—just enough to drop the coolant level below the thermostat housing. Locate and Remove the Housing: The thermostat is inside a housing (often aluminum or plastic) connected to the engine block by the upper radiator hose. Unbolt this housing. You might need extensions and a swivel socket to reach awkwardly placed bolts. Swap the Thermostat: Carefully pry out the old thermostat. Note its orientation—the spring side typically faces the engine. Clean the mating surfaces on the engine and housing completely. Place the new thermostat in position, ensuring it sits correctly. Install a new gasket (often included with the thermostat) – using a thin layer of gasket sealant is sometimes recommended. Reassemble and Refill: Reattach the housing and tighten the bolts evenly to the manufacturer's specified torque to avoid leaks. Close the drain, refill the cooling system with a 50/50 mix of coolant and distilled water, and run the engine with the radiator cap off to burp air bubbles out of the system. Common Thermostat Failure Symptoms & Associated Costs Symptom Description Typical DIY Part Cost Professional Repair Cost Engine Overheating Thermostat stuck closed, blocking coolant flow. $20 - $50 $200 - $400 Slow Warm-Up Thermostat stuck open, engine takes too long to heat up. $20 - $50 $200 - $400 Erratic Temperature Gauge Fluctuating readings due to a sticking thermostat. $20 - $50 $200 - $400 Poor Heater Performance Engine not reaching temperature prevents cabin heat. $20 - $50 $200 - $400 Coolant Leak Leaking from the housing gasket due to improper seal. $20 - $50 (includes gasket) $200 - $400
13
5
Share

how to fix a ripped car seat

The best way to fix a ripped car seat depends on the size of the tear, the seat material (cloth, vinyl, or leather), and your DIY skill level. For small tears under two inches, a DIY repair using a vinyl/leather repair kit or a fabric repair patch is a cost-effective and permanent solution. Larger tears or damage to the seat's structural foam often require professional re-upholstery or seat cover replacement to ensure a safe and aesthetically pleasing result. Assessing the Damage First, examine the rip closely. Is it a clean cut or a jagged tear? Is the underlying foam padding damaged? Cleaning the area around the tear with isopropyl alcohol is crucial for any adhesive to bond properly. For cloth seats, a tear can quickly worsen due to stress, so addressing it promptly is key. Repair Methods by Material Vinyl/Leather Seats: A repair kit is your best bet. These kits include a color-matched compound and a grained paper or metal tool to melt and texture the patch, blending it with the surrounding material. The process involves applying a filler, heating it to cure, and then stamping a grain pattern onto it. Cloth Seats: Fabric repair patches, which are essentially heavy-duty, iron-on adhesives, work well. You apply the patch to the underside of the tear. For a more invisible fix, some kits include a backing patch and a pile material you can glue on top to mimic the original texture. When to Call a Professional If the tear is large, on a seam, or if the foam is compromised, DIY fixes will look temporary and may not be safe. An auto upholstery shop can re-stitch a seam, replace a panel, or install a new cover section. While more expensive, this guarantees a factory-quality finish. Repair Method Ideal Tear Size Estimated Cost Skill Level Required Longevity Vinyl/Leather Repair Kit < 2 inches $20 - $50 Intermediate 2-5 years Fabric Repair Patch < 3 inches $10 - $25 Beginner 1-3 years Professional Re-upholstery Any size, complex damage $200 - $600+ Expert (Pro) 10+ years Seat Cover Replacement Large areas, worn bolsters $150 - $400 (parts) Intermediate/Pro 10+ years Stitching by Hand Clean cuts on seams $5 (thread/needle) Advanced Beginner Permanent if done well
18
0
Share

how to fix suspension on car

Fixing a car's suspension is a complex task that ranges from a straightforward strut replacement to a full system overhaul. The correct approach depends entirely on accurate diagnosis. For most DIYers, replacing complete, pre-assembled strut assemblies is the safest and most practical method for common issues like a bouncy ride or knocking sounds. However, jobs involving springs, which are under extreme pressure, should be left to professionals due to the significant safety risk. The first step is always a thorough inspection. Look for visible signs of damage like fluid leaks from the shock absorbers or struts, torn rubber bushings, or uneven tire wear. Listen for clunks or rattles over bumps, which often point to worn control arms or sway bar links. A bouncy ride after going over a bump typically indicates worn shocks or struts. For a front-wheel-drive car, a common repair is replacing a MacPherson strut , which combines a shock absorber and a spring into a single structural unit. The safest DIY method is to install a pre-assembled strut assembly , which comes with a new spring, mount, and shock already compressed. This eliminates the need for dangerous spring compressors. Other common fixes include swapping out worn stabilizer bar links (sway bar links) or ball joints , which are more manageable for those with moderate mechanical experience. Repair Task DIY Difficulty Professional Recommended? Key Risk Replacing Stabilizer Bar Links Low No Low risk; simple bolt-on replacement. Replacing Pre-assembled Struts Moderate For experienced DIYers Incorrect installation affects alignment and safety. Replacing Shock Absorbers (separate from springs) High Yes Requires spring compressors; high risk of injury. Replacing Control Arms/Ball Joints Moderate-High Yes Critical for wheel alignment and structural integrity. Replacing Leaf Spring Shackles/Bushings Moderate Maybe (depends on rust) Often seized bolts require significant force. You'll need a good set of socket wrenches, jack stands, a torque wrench, and penetrating oil. Never work under a car supported only by a jack. After any suspension work, a wheel alignment is absolutely critical. Changing suspension components will alter the angles of the wheels, leading to rapid tire wear and poor handling if not corrected by a professional alignment shop.
3
3
Share

how to get a copy of car key

Getting a copy of a car key depends entirely on your car's year, make, and technology. For most modern vehicles (roughly 2010 and newer), you'll need to visit a dealership or a qualified automotive locksmith to program a new key fob or transponder key, which can cost significantly more than a simple metal key duplicate. The process involves both cutting the physical key and syncing its electronic code to your car's immobilizer system. The first step is to identify what type of key you have. A basic mechanical key without any electronics is the easiest and cheapest to copy at a hardware store. Most modern keys, however, are transponder keys (with a chip inside), key fobs (keyless entry remotes), or smart keys (push-to-start fobs). These require specialized programming. You will need to provide proof of ownership, such as your vehicle's title and registration, and a valid driver's license. This is a standard security measure for all reputable key providers. Here’s a quick comparison of the two main options: Service Provider Typical Cost Range Pros Cons Best For Dealership $200 - $800+ Guaranteed compatibility, uses OEM parts. Highest cost, may require towing the car there, longer wait times. Newer cars, complex smart keys, if you want factory-original parts. Auto Locksmith $100 - $400 Often more affordable, can provide mobile service to your location. May not have programming tools for all exotic or very new models. Most transponder keys and standard fobs, convenient and cost-effective. Hardware Store $2 - $10 Extremely low cost, immediate service. Only works for basic, non-electronic mechanical keys. Older cars (pre-1990s) or valet keys. For a key fob replacement, the locksmith or dealer will need to connect a diagnostic computer to your car's OBD-II port (usually under the dashboard) to program the new key's unique code. If you've lost all your keys, the process is more complex and expensive, as it may require resetting the car's entire immobilizer system.
20
5
Share

how to fix sun damage on car

The best way to fix sun damage on your car depends entirely on the severity. For light UV damage like faded paint and minor oxidation, a thorough paint correction process—involving claying, compounding, and polishing—can often restore the finish. However, if the clear coat is peeling or the paint has severe cracking (crazing), a complete repaint of the affected panel is usually the only permanent solution. For damaged interior plastics and vinyl, specialized interior restoration products can temporarily rejuvenate them, but cracked dashboards may require replacement. Sun damage manifests in stages. The first sign is often oxidized paint , which looks dull and chalky. This is just the clear coat degrading. Using a clay bar to remove embedded contaminants, followed by a cutting compound to level the oxidized layer, and finally a polish to restore gloss can work wonders. For deeper scratches or clear coat failure where the paint appears whitish and is peeling, sanding and repainting are necessary. Ignoring this will lead to rust. Interior surfaces take the brunt of the heat. A faded dashboard can be treated with a UV-protectant dressing, but it’s a temporary fix. For cracked vinyl , there are repair kits that fill the cracks, but the result is rarely seamless. Prevention is always cheaper than the cure. Consistent use of a high-quality carnauba wax or ceramic coating and a sunshield can prevent most of these issues from occurring in the first place. Severity of Damage Visible Signs Recommended Fix Estimated Cost (Parts/Labor) Professional vs. DIY Light Oxidation Dull, chalky paint Paint correction (compound & polish) $150 - $400 DIYable with skill Moderate Swirls/Fading Visible fine scratches Machine polishing & sealant $300 - $600 Best left to pros Severe Clear Coat Failure Peeling, whitish patches Sand & repaint panel $500 - $1,500+ Professional only Faded Plastic Trim Grayish, faded appearance UV-protectant dressing $20 - $50 Easy DIY Cracked Dashboard Physical cracks in vinyl Dashboard repair kit or replacement $100 (kit) / $1,000+ (replace) DIY kit / Pro replacement
8
0
Share

how to fix scraped car paint

Fixing scraped car paint depends entirely on the depth of the damage. For light clear coat scratches that you can't feel with your fingernail, a DIY repair with polishing compound is often successful. If the scratch has penetrated the base coat (color layer) but not the primer, touch-up paint is your best bet. Deep scratches that expose bare metal require immediate professional attention to prevent rust. The first step is always a thorough wash and dry of the area. Contaminants like dirt will ruin any repair attempt. To assess the scratch, gently drag your fingernail across it. If your nail doesn't catch, the scratch is likely superficial. For Clear Coat Scratches: This is the simplest fix. Use a rubbing compound applied with a microfiber cloth, working in small, circular motions. This process, known as compounding, abrades a thin layer of clear coat to level it with the scratch. Follow up with a polishing compound to restore gloss. Finally, apply a coat of wax to protect the area. For Base Coat Scratches: You'll need an exact-match touch-up paint, usually available from your dealership or auto parts store. Carefully apply the paint in thin layers using the included brush or a fine toothpick, filling the scratch. Let each layer dry completely before applying the next. Once the color is built up and slightly higher than the surrounding paint, you can lightly wet sand it flush once it's fully cured (after about 30 days) and then polish. Repair Method Scratch Depth Estimated DIY Cost Professional Cost Key Tools/Products Needed Polishing Clear Coat Only $15 - $30 $100 - $200 Rubbing Compound, Polisher, Microfiber Cloths Touch-Up Paint Base Coat (Color Layer) $20 - $50 $150 - $400 OEM Touch-Up Paint, Fine Applicator Professional Repaint Primer or Metal Exposed N/A $500 - $1,500+ Sandpaper, Primer, Paint, Clear Coat, Spray Gun Deep scratches are a different story. If you see a dull gray layer (primer) or, worse, shiny bare metal, the panel is vulnerable to rust. A professional auto body shop will need to sand the area, apply primer, base coat, and clear coat, then blend it with the surrounding paint for a seamless finish. Attempting a DIY repair on this level of damage often results in a noticeable, unprofessional look.
8
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.