What is the difference between ACC adaptive cruise control and regular cruise control?

Where is the location to add windshield washer fluid for Toyota Corolla?

Toyota Corolla's windshield washer fluid reservoir is located on the left side of the engine compartment, featuring a small blue-capped container. Near the vehicle's front power source, there is another small filling port. The container with a windshield washer symbol on its cap is the windshield washer fluid reservoir - simply open it and pour in the antifreeze washer fluid. Windshield washer fluid is a liquid used to clean the windshields of vehicles and other transportation tools, serving as a consumable automotive product. It mainly consists of water, alcohol, ethylene glycol, etc., and functions for cleaning, antifreeze, and anti-fog purposes. The Toyota Corolla comes with two engine options, both utilizing dual VVTI technology: a 1.6L engine with a maximum power output of 90KW and peak torque of 154NM, and a 1.2T engine delivering 85KW maximum power and 185NM peak torque.

7

2

Share

What are the exterior differences between the Prado 2.7 and 4.0?

The exterior differences between the Prado 2.7 and 4.0 are: 1. Different rear badges: The 2.7 model does not have 'FAW Toyota' on the tailgate, while the 4.0 model does. 2. Different roof configurations: The 2.7 does not have a sunroof, whereas the 4.0 comes with a sunroof. 3. Different model badges: The 2.7 is only available in the GX version, while the 4.0 offers both GX and VX versions. The 2.7 version is equipped with Toyota's 2.7L V6 2GR engine with a maximum power output of 120KW, while the 4.0 version features Toyota's 4.0L V6 1GR engine with a maximum power output of 202KW. The 2.7 has always been imported and has not been domestically produced.

9

3

Share

How to Solve Oxygen Sensor Problems?

Solutions for oxygen sensor problems: 1. Warm up the engine to normal operating temperature; 2. Connect the negative probe of the multimeter's voltage range to the E1 terminal in the fault detection socket or the negative terminal of the battery, and the positive probe to the OX1 or OX2 terminal in the fault detection socket, or to the output wire on the oxygen sensor harness connector; 3. Keep the engine running at around 2500 RPM and check if the voltmeter needle can swing back and forth between 0 and 1V. Record the number of times the voltmeter needle swings within 10 seconds. Under normal conditions, with feedback control in progress, the oxygen sensor's feedback voltage continuously fluctuates around 0.45V. If the number of swings is fewer than 8, it indicates that the oxygen sensor or feedback control system is not functioning properly. The reason is likely carbon buildup on the oxygen sensor surface, which reduces sensitivity. To address this, run the engine at 2500 RPM for about 2 minutes to remove the carbon deposits from the oxygen sensor surface.

18

1

Share

What is the parking sequence?

Parking sequence is: 1. Shift into R gear and quickly turn the steering wheel all the way to the right, reversing until the car is at about a 45-degree angle to the parking space, usually when the left rearview mirror can see the license plate of the rear car; 2. Quickly straighten the steering wheel and continue reversing straight back; 3. When the front of the car aligns with the rear of the car in front, or you can open the window to observe, and the left rear wheel is ready to enter the parking space, you can quickly turn the steering wheel all the way to the left and continue reversing; 4. Once the left front wheel enters the parking space, you can straighten the steering wheel and then adjust the car's position. To park the car into the so-called parking space, the first thing to do is to ensure the space is large enough. If it's a roadside parallel parking space, it's recommended to choose a space that is at least one meter longer than the car's length for safety. When the line of sight from the driver's perspective to the right front corner of the hood aligns behind the left rear wheel of the car in front, it is relatively safer.

11

2

Share

Where is the AUX interface in the new Focus?

The AUX interface in the new Focus is located inside the glove compartment in front of the passenger seat. Simply open the glove compartment lid to find it. The AUX is an audio input interface, and its basic working principle is that after connecting to the AUX interface, audio from electronic devices can be transmitted through the headphone jack and AUX interface to the car's audio system, allowing playback through the car's audio broadcasting facilities. The USB interface can be used to insert a USB drive for audio playback. When using the AUX interface, connect one end to the AUX port and the other end to devices like smartphones, MP3 players, or MP4 players. This allows you to listen to songs or niche music anytime, anywhere, without being limited to car music CDs. However, if the playback device runs out of battery, the music will stop (the interface typically uses a standard 3.5mm headphone jack). Aux, short for Auxiliary, refers to an additional signal line design. In general audio equipment, besides the standard output and input terminals, there are often several terminals labeled Aux, serving as backup connection points. These can be used for special applications, such as additional audio output or input. Such backup terminals or lines, whether for input or output, are collectively referred to as Aux. Function: The AUX port is an asynchronous port primarily used for remote configuration, dial-up connections, or connecting to a MODEM via a transceiver. It supports hardware flow control. The AUX port is usually placed alongside the CONSOLE port because they serve different configuration environments. The AUX interface establishes a command-line connection between the user and the device, enabling operations that are typically impossible in user mode, such as initialization, restoring default settings, or correcting abnormal user modes. It provides a fixed port that can function as a standard asynchronous serial port with a maximum speed of 115200 bit/s. Using the AUX interface, remote configuration of hardware products and line backup can be achieved. Note: When using the AUX interface, ensure you purchase the correct connecting cable and avoid plugging the audio cable into the wrong port. It’s best to follow the steps outlined in the product’s user manual. If unsure, consult the product’s official website or contact customer service for guidance.

5

1

Share

What is equipment-related violation?

Equipment-related violation mainly refers to violations where production-related equipment and facilities do not meet regulatory requirements. Below is an introduction to equipment-related violations: 1. Definition of equipment-related violation: It refers to situations where the working environment, equipment, facilities, and tools do not comply with relevant technical regulations such as the "Electric Power Industry Safety Work Regulations" and various provisions and technical measures for ensuring personal safety, and where safety measures cannot guarantee the safety of personnel and equipment. 2. Responsible parties for equipment-related violations: These are management personnel, supervisors or direct leaders of the equipment (or facilities). Those responsible for accidents caused by equipment-related violations will be held accountable.

14

1

Share

What is the difference between ACC adaptive cruise control and regular cruise control?

Where is the location to add windshield washer fluid for Toyota Corolla?

What are the exterior differences between the Prado 2.7 and 4.0?

How to Solve Oxygen Sensor Problems?

What is the parking sequence?

Where is the AUX interface in the new Focus?

What is equipment-related violation?

How to Reset the Maintenance Reminder for the 2018 Magotan?

Does the Highlander have a 7-seater version?

What does the car plus-minus light indicate as a fault?

How to Check the Score Confirmation Sheet for Subject 3?